InFocus Projector IN1126 User Manual

							
User’s Manual 
Video/Audio Menu  
Press the MENU button to open the  OSD menu. Press the cursor  ◄► button to move to the  
Video/Audio  menu. Press the cursor  ▲▼ button to move up and down in the  Video/Audio menu. 
Press  ◄► to change setting values. 
 
ITEM DESCRIPTION 
Press the  ◄► buttons to enable or disable the Automatic Gain Control for video 
source. Video AGC 
Video Saturation Press the  ◄► buttons to adjust the video saturation. 
Video Tint Press the  ◄► buttons to adjust the video tint/hue. 
Film Mode Press the  ◄► buttons to select a different film mode.  
Video Overscan Press the  ◄► buttons to enable or disable Video Overscan. 
Closed Captioning Press the  ◄► buttons to enable or disable Closed Captioning. 
Audio Press  (Enter) / ►  to enter the Audio menu. See  on page 25. Audio
Reset Press  (Enter) / ► to reset all settings to default values. 
 
Note: 
Video jagging may occur when playing interlaced  video. To overcome this issue, open the  
Video / Audio menu and adjust the Film Mode feature.  
– 24 –  
						

							
IN1124/IN1126 – User’s Manual 
Audio 
 (Enter) / ► to enter the  Audio sub menu. Press 
 
ITEM DESCRIPTION 
Volume Press the ◄►  buttons to adjust the audio volume.  
Mute Press  the ◄►  buttons to turn the speaker on or off. 
 
   – 25  –  
						

							
User’s Manual 
 Installation I Menu  
Press the MENU button to open the  OSD menu. Press the cursor  ◄► button to move to the  Installa-
tion I  menu. Press the cursor  ▲▼ button to move up and down in the  Installation I menu. Press 
◄►  to change setting values. 
 
 
ITEM DESCRIPTION 
Press the cursor  ◄► buttons to select a different localized menu. 
(Range: English/ Français/ Español/ Deutsch/ Português/  簡体中文/ 繁體中文/ Italiano/ 
Svenska/ Nederlands/ Suomi/  Dansk/ Norsk/ Polski/ 한국어/ Türkçe/  Русский/ Bahasa 
Indonesia/ 
Language 
ﺔﻴﺑﺮﻌﻟا/ Tiế ng Anh) 
Blank Screen Press the cursor  ◄► button to select different color to blank the screen. 
Press the cursor  ◄► button to choose from four  projection methods: Front, Rear, 
Ceiling, Rear + Ceiling Projection 
Aspect Ratio Press the cursor ◄►  button to adjust the video aspect ratio. 
Keystone Press the cursor ◄► button to adjust trapezoid images. 
Digital Zoom  Press the cursor ◄►  button to adjust the Digital Zoom.  
Advanced Press  (Enter) / ► to enter the Advanced menu. See 
– 26 – 
Advanced on page 27. 
Press  (Enter) /  ► to reset all Installation1 settings to default values  
(expect Language and Security Lock). Reset  
						

							
IN1124/IN1126 – User’s Manual 
Advanced 
 (Enter) / ► to enter the  Advanced sub menu. Press 
 
ITEM DESCRIPTION 
Security Lock  Press the cursor  ◄► button to enable or disable the security lock function. 
Keypad Lock Press the cursor  ◄► button to enable or disable the keypad lock function. 
When displaying the image against a wall, press the cursor ◄► button to select dif-
ferent wall color settings. This will help compensate for color variations caused by the 
wall surface.  
Wall Color 
Press  (Enter) / ► to enter the Presentation Timer menu. See  Presentation Timer 
below Presentation Timer 
Software Version Display the so ftware version information. 
Presentation Timer 
 (Enter) / ► to enter the  Presentation Timer  sub menu.  Press 
 
ITEM DESCRIPTION 
Timer Press the cursor ◄► button to enable or disable the presentation timer function. 
Timer Period Press the cursor  ◄► button to adjust the display timer period. 
Timer Reset Press  (Enter) / ►  to reset the presentation timer counter. 
   – 27  –  
						

							
User’s Manual 
Installation II Menu  
Press the MENU button to open the  OSD menu. Press the cursor  ◄► button to move to the  Installa-
tion II  menu. Press the cursor  ▲▼ button to move up and down in the Installation II menu.  
 
ITEM DESCRIPTION 
Auto Source Press the cursor  ◄► button to enable or disable automatic source detection.  
Auto Power Off 
(min.) Press the cursor  ◄► button to enable or disable automatic shutdown of lamp when 
no signal.  
Press the cursor  ◄► button to enable or disable Automatic Power On when AC power is 
supplied. Auto Power On 
Press the cursor  ◄► button to toggle between Normal and High fan speeds.  
Note: We recommend selecting high speed in high temperatures, high altitude areas. 
26~30°C 
( 78.8~86
°F ) 
31~35°C  
( 87.8~95°F )  ≦  25°C                 ( 77°F ) 
0~4,999ft 
( 0~1523m )  Normal Mode Fan Speed 5,000 ft      
( 1524m )  Normal Mode High Speed Mode 
7,500 ft    
( 2286m )  High Speed Mode ---------- 
10,000 ft  
( 3048m )  High Speed Mode------------ --------  
Press the cursor  ◄► button to select the lamp mode for higher brightness (Normal) or 
lower brightness (Eco) to save lamp life. Lamp Mode 
Press  (Enter) /  ► to enter the Advanced menu. See Advanced Features on page Advanced 29. 
Factory Reset Press  (Enter) / ►
 to reset all OSD settings to factory default settings. 
Press  (Enter) / 
►
 to enter the Status menu. See page 31 for more information on Status Status. 
 
– 28 –
  
						

							
IN1124/IN1126 – User’s Manual 
Advanced Features 
Press the Menu button to open the OSD menu. Press  ◄► to move to the  Installation II menu. 
Press  ▲▼ to move to the  Advanced menu and then press  Enter or ►. Press  ▲▼ to move up and 
down in the  Advanced menu. Press  ◄► to change setting values. 
 
ITEM DESCRIPTION 
Press Enter /  ► to enter the OSD setting menu. See page 30 for more information on OSD Menu Setting OSD Menu Setting. 
Press Enter/  ► to enter the Peripheral Test menu. See page 30 for more information 
on Peripheral Test Peripheral Test. 
After replacing the lamp, this item should be reset. See page 31 for more information 
on Lamp Hour Reset Lamp Hour Reset. 
Press  ◄► to turn Low Power Mode on or off.  This affects power consumption when 
the projector is in standby. When this featur e is on, the projector will use less than 1 
watt of electricity in standby mode. When th is feature is off, the projector will use 9 
watts of electricity in standby mode. 
Low Power Mode 
 
   – 29  –  
						

							
User’s Manual 
OSD Menu Setting  
 
ITEM DESCRIPTION 
Menu Position Press ◄► button to move the OSD menu position. 
Translucent Menu Press ◄►  button to adjust the OSD opacity.  
Menu Display Press ◄► button to select the OSD timeout delay. 
 
Peripheral Test 
 
ITEM DESCRIPTION 
Remote Control 
Test  (Enter) /  ► to test the IR remote control for diagnostic testing.  Press 
Color Test Press  (Enter) / ►  to display colored test patterns. 
Button Test Press  (Enter) / ► to test the keypad buttons. 
USB Test Press  (Enter) / ► to test the USB connection with the connected PC. 
Sound Test Press  (Enter) / ► to test the audio output. 
– 30 –  
						

							
IN1124/IN1126 – User’s Manual 
Lamp Hour Reset 
 
Please refer to  on page 32 to reset the lamp hour counter. Replacing the Projection Lamp
Press ▼▲◄►  buttons to reset the lamp hour 
 
Status 
Press the cursor ▲▼  button to move up and down in the  Installation II menu. Select the   
Installation II sub menu and press 
 (Enter) /  ► to enter the  Status sub menu.
 
 
ITEM DESCRIPTION 
Active Source Displays the active source. 
Displays resolution/video information for RGB source and color standard for Video 
source. Video Information 
Lamp Hours Displays the number of hours the lamp has been used in Eco and Normal modes. 
 
   – 31  –  
						

							
User’s Manual 
 
MAINTENANCE AND SECURITY 
Replacing the Projection Lamp 
Be sure to use the InFocus lamp module designed for this projector. You can order new lamps from 
www.infocusstore.com (in select areas), your retaile r or your dealer. Only genuine InFocus lamps are 
tested for use in this projector.  Use of non InFocus lamps may caus e electrical shock and fire, and may 
void the projector warranty. InFocus is not liable for  the performance, safety or certification of any other 
lamps. 
Warning: 
• The projector uses a high-pressure mercury glass lamp. The lamp may fail prematurely, or it   
may rupture with a popping sound if jolted, scratched, or handled while hot. The risk of lamp 
failure or rupture also increases as the lamp age increases. 
• Do not touch or block the projector lens with any objects as this can damage the projector 
lens. Scratches, gouges and other lens damage are not covered by the product warranty. 
• Unplug the power cord before replacing the lamp. 
• Do not drop the lamp module. The glass may shatter and cause injury. 
• Do not touch the glass surface of the lamp module. Fingerprints can obscure projection 
sharpness and may cause the glass to shatter. 
• Be extremely careful when removing the lamp housing. In the unlikely event that the lamp 
ruptures, small glass fragments may be generated. The lamp module is designed to contain 
most of these fragments, but use caution when removing it. 
• Before replacing a ruptured lamp, clean the lamp compartment and dispose of cleaning mate-
rials. Wash hands after lamp replacement. 
• When replacing the lamp while the projecto r is ceiling-mounted, wear protective eye-
wear to prevent eye injury.  
• Hg – Lamp contains mercury. Manage in accordance with local disposal laws. See 
www.lamprecycle.org. 
• Be sure to turn off and unplug the projector at least 60 minutes before replacing the lamp. 
Failure to do so could result in a severe burn. 
1.  Wait 60 minutes for the 
lamp to cool before at-
tempting to replace lamp. 
Then loosen the two cap-
tive screws on the lamp 
compartment cover (A). 
2.  Remove the lamp com-
partment cover ( B). 
 
– 32 –   
						

							
IN1124/IN1126 – User’s Manual 
3.  Remove the two screws 
from the lamp module (A). 
4.  Lift the module handle up 
(B). 
 
5.  Pull firmly on the module 
handle to remove the lamp 
module. 
 
6.  Reverse steps 1 to 5 to 
install the new lamp 
module.  
While installing, align the 
lamp module with the 
connector and ensure it is 
level to avoid damage. 
Note:  
The lamp module must sit 
securely in place and the 
lamp connector must be 
connected properly before 
tightening the screws.  
7.  Turn on the projector and reset the lamp after the lamp module is replaced. 
Lamp Reset:  
Press  Menu  → Select Installation II  / Advanced  → Select Lamp Hour Reset  → Press 
the ► or 
   buttons → Press  ▼▲◄► buttons to reset the lamp hour. 
Press the  MENU button to get back to Installation II. 
   – 33  –