InFocus Projector IN1100 User Manual

1
Declaration of Conformity
Manufacturer: InFocus Corporation 13190 SW 68th Parkway, Portland, Oregon 97223-8368 
USA 
We declare under our sole responsibility that this projector 
 conforms to the following 
directives and norms:
EMC Directive 2004/108/EC
EMC: EN 55022EN 55024
EN 61000-3-2
EN 61000-3-3
Low Voltage Directive 2006/95/EC
Safety: IEC 60950-1: 2005
Tr a d e m a r k s
Apple, Macintosh, and PowerBook are tradem arks or registered trademarks of Apple 
Computer, Inc. IBM is a trademark or...

2
Table of Contents
Introduction
3
Positioning the projector 5
Connecting a computer source 6
VESA connection 6
HDMI connection 6
Power connection 6
Optional computer connections 6
Displaying an image 7
Adjusting the image 8
Video device connections 9
Composite video connection 9
HDMI 1.3 connection 9
S-video connection 9
VESA connection 9
Component video connection 9
Shutting down the projector 10
Troubleshooting your setup 10
Using the remote control 18
Using the audio 19
Using the keypad buttons 20...

3
Introduction
Your new digital projector is simple to connect, easy to use, and straightforward to 
maintain. The IN1110 has native XGA 1024x 768 resolution, and the IN1112 has 
WXGA 1280x800 resolution. This guide a pplies to all products. They are 
compatible with a wide variety  of computers and video devices.
Product specifications
To read the latest specifications on your mu ltimedia projector, be sure to visit our 
website at  www.infocus.com , as specifications are subject to change.
Accessories...

4
Connector panel
The projector provides the following connectors:
• MINI USB Type B connector: Used 
for advancing slides and firmwar
 e 
upgrades.
• VESA computer
•S-video
• Composite video
• HDMI
• Audio out
• Audio in
USBcomputer inHDMIvideo 1video 2audio outaudio in
audio  out
S-video
computer composite 
video
security lock
MINI USB 
Type B 
audio 
in
HDMI 

5
Positioning the projector
To determine where to position the projector, consider the size and shape of your 
screen, the location of your power outlets, and the distance between the projector 
and the rest of your equipment.  Here are some general guidelines:
• Position the projector on a flat surface  at a right angle to the screen. The 
projector must be at least 4.9 feet  (1.5m) from the projection screen.
• Position the projector within 10 feet (3m)  of y
 our power source and within 6 
feet (1.8m)...

6
Connecting a computer source
VESA connection
Connect one end of the provided computer cable to the Computer connector on the 
projector and the other to the VESA connector on your computer. If you are using a 
desktop computer, you will need to  disconnect the monitor cable from the 
computer’s video port first.
HDMI connection
HDMI is a standard, uncompressed, all- digital audio/video interface. HDMI 
provides an interface betw een sources, such as set-top boxes, DVD players, and 
receivers and your...

7
Displaying an image
Touch the Power button.
The Power indicator blinks green and the fans start to run. When the lamp comes 
on, th e start u

p screen displays and the Power indicator is steady green. It can take a 
minute for the image to ach ieve full brightness.
? No start up screen?  Get h

elp on page 11 .
Turn on your computer or video device.
The image should appear  on the projection
  screen. If it doesn’t, press the Source 
button on the projector’s keypad  or remote. Then navigate to the...

8
Adjusting the image
If necessary, adjust the height of the projector by pressing the elevator foot release 
button to extend the foot.
If necessary, rotate the leveling foot located at the rear of the projector.
Avoid placing your hands near the hot exhaust vent 
 at the side of the projector.
Position the projector the desired distance  from the 
 screen at a 90 degree angle to 
the screen.
See  page  5 for a table listing scre en
  sizes and distances.
Adjust the zoom or focus, as needed.
If the...

9
Video device connections
No video cables are provided with the projector. You can order cables from 
InFocus or provide your own.
Composite video connection
Plug a composite video cabl e’s yellow connector into the video-out connector on 
the video device. Plug the other ye llow connector into the yellow Video 2 connector 
on the projector.
Plug the white connector of a Mini-plug  au
 dio Y-cable into the left audio out 
connector on the video device and plug th e red connector into the right audio out...