Iiyama Prolite E1908wsv User Manual

ENGLISH
BEFORE YOU OPERATE THE MONITOR     7
CONNECTING YOUR MONITOR
[Example of Connection] AEnsure that both the computer and the monitor are switched off.
BConnect the computer to the monitor with the signal cable.
CConnect the monitor to the audio equipment with the Audio Cable when using the audio features.
DConnect the Power Cable to the monitor first and then to the power supply.
NOTE„The signal cables used for connecting the computer and monitor may vary with the type of
computer used. An...

ENGLISH
20
5
ADJUSTING THE VIEWING ANGLE
„For optimal viewing it is recommended to look at the full face
of the monitor.
„Hold the stand so that the monitor does not topple when you
change the monitor’s angle.
„You are able to adjust the monitor’s angle up to 20 degrees
upward, 5 degrees downward.
„In order to ensure a healthy and relaxed body position when
using the monitor at visual display workstations, it is
recommended that the adjusted tilt angle should not exceed
10 degrees. Adjust the monitor’s...

ENGLISH
OPERATING THE MONITOR     9
The bar shows 
the progress of the 
adjustment being made.+
–50
V-Position
Menu:1
1680 × 1050
H:65.4KHz  V:60.1Hz
DCROFF
OPERATING THE MONITOR
To create the best picture, your iiyama LCD monitor has been preset at the factory with the COMPLIANT
TIMING shown on page 23. You are also able to adjust the picture by following the button operation
shown below. For more detailed adjustments, see page 16 for SCREEN ADJUSTMENTS.
( (( (
(Press the Menu Button to start the On...

ENGLISH
ADJUSTMENT MENU CONTENTS
You can skip the Menu pages and display an adjustment scale directly by using the
following button operations.
zBrightness / Contrast / Economy Mode / Picture Mode / Volume / DCR:
To display direct menu press either of the +/- Buttons.
Continue to use the +/- Buttons to select the adjustments
required.
z  Auto Set-up: Press the Auto Button when the Menu is not displayed.
z  Volume (Mute): With the OSD menu off, the pressing and holding of the Menu Button for 1-2
seconds...

ENGLISH
OPERATING THE MONITOR     11
Menu:1
1680 × 1050
H:65.4KHz  V:60.1Hz
DCROFF
Adjustment Item Problem / Option                       Button to Press
Too dark
Too brightBrightness *1
ContrastToo dull
Too intense
To correct flickering text or linesClock *2
Phase *2
H-PositionToo far to the left
Too far to the right
V-PositionToo low
Too high
Return to MenuHighlight “Menu : 1” again.
To correct flickering text or lines
Direct
Direct
*1Adjust the Brightness when you are using the monitor in a dark room...

ENGLISH
Menu:2
1680 × 1050
H:65.4KHz  V:60.1Hz
DCROFFMenu : 2
On
Problem / Option                                                  Button to Press Adjustment Item
Color Temp.
Color 1: 9300K Auto Set-up *
3NO
YESReturn to Menu.
Adjust Clock, Phase, V-Position and H-Position
automatically.
Direct
*3For best results, use the Auto Set-up in conjunction with the adjustment pattern. See page 16 for
SCREEN ADJUSTMENTS.
1
NOTE„sRGB is an international standard which defines and unifies the difference of color...

ENGLISH
OPERATING THE MONITOR     13
Normal
Menu : 2
Return to MenuHighlight “Menu : 2” again.
Off
Mode1High contrast
Dark
Gamma
Mode1Brightness of back-light is reduced.
Mode2Brightness of back-light is reduced more than Mode1.Economy ModeOffNormal
Mode2
Problem / Option Adjustment Item
NOTE„       is displayed while Economy Mode is active.
Sharpness1 2 3 4 5
Adjust the picture quality at resolutions of less than 1680 ×
1050.
You can change the picture quality from 1 to 5 (sharp to soft).
Press the +...

ENGLISH
Menu : 3
Japanese
Adjustment Item
Menu:3
1680 × 1050
H:65.4KHz  V:60.1Hz
DCROFF
Problem / Option                                             Button to Press
OSD Position1 2 3 4 5
You can move the OSD display area
to any one of the following 5 positions
within the overall display:
Italiano LanguageEnglish
DeutschEnglish
FrançaisEspañol
FrenchSpanish
Press the + Button to move the OSD in numerical order. Press
the – Button to move the OSD in reverse numerical order.
NOTE
OSD Off TimerSet the OSD...

ENGLISH
OPERATING THE MONITOR     15
Menu : 4
Adjustment Item
Menu:4
1680 × 1050
H:65.4KHz  V:60.1Hz
DCROFF
DCR
Problem / Option                                             Button to Press
Too soft
Too loud
VolumeDirect
Return to Menu
Highlight “Menu : 4” again.
ResetNO
YESReturn to Menu.
Factory-preset data is restored.
NOTE„       is displayed while Mute is active.
See page 10 for Direct adjustment.Direct
DCR adjusts brightness according to the image, and improve the contrast ratio during
move...

ENGLISH
SCREEN ADJUSTMENTS
„The screen adjustments described in this manual are designed to set image position and minimize
flicker or blur for the particular computer in use.
„The monitor is designed to provide the best performance at resolution of 1680 × 1050, but can not
provide the best at resolutions of less than 1680 × 1050 because the picture is automatically stretched
to fit the full screen. It is recommended to operate at resolution of 1680 × 1050 in normal use.
„Displayed text or lines will be...