Iiyama Prolite E1908wsv User Manual

							USER MANUAL
Thank you very much for choosing the iiyama
LCD monitor.
We recommend that you take a few minutes to
read carefully through this brief but
comprehensive manual before installing and
switching on the monitor. Please keep this
manual in a safe place for your future
reference.
ENGLISHENGLISH
DEUTSCH
FRANCAIS
NEDERLANDS
 
						

							ENGLISH
| Servicecard
Dear user, we congratulate you
on the purchase of your iiyama LCD.
iiyama
All iiyama LCD monitors comply with the ISO13406-2 standard for pixel defects. 
For details on warranty and locally used pixel policies that apply directly after installation of your product 
please check the iiyama website.
In case of a defect, please call your local support hotline.
Before reporting the screen defect, please 
prepare the following information/evidence:
| model number *
| purchase receipt and serial number *
| shor t description of the defect
Important 
Note:
If there is no fault found in the collected 
equipment after inspection,
the transferring par ty shall incur charges 
for transport and administration. 
* see the identification plate on the back of the case.
Things to check before you call the iiyama information line 
If you have checked all of the above and there is still no picture, call our information line for assistance in your country.  | if the power cable is connected securely and turned on?
| if the display has been turned on?
| if the signal cable is connected securely and the correct input selected?
| if the computer has been restarted with the display connected?
| if the graphics card is correctly installed with the latest drivers possible?
| if the correct native resolution has been selected via Display Properties?| If the R/G/B signal configuration is correct?
| if the displays On Screen Menu is shown?
| if the correct brightness and contrast settings have been set?
| if given display tolerances and compatibility have been considered?
| if via the On Screen Menu you have performed 
  a Factory Reset/Recall?
www.iiyama.com
Austria +49 1805 44 92 62 
Belgium +31 30 240 80 20
Bulgaria 0 2 9880300
Czech Republik 220 121 432
Denmark 0 96 360 374
Estonia 0 6671796
Finland  0 9 56186130
France  0 825 828 936
Germany  0 1805 44 92 62
Great Britain 0 870 224 95 95 
Greece 0 210 289 2000
Hungary  06 1 814 8080; 06 1 340 9951
Italy  +49 1805 44 92 62
Latvia 0 7408838
Lithuania 0 37 328442;  0 52 2101160 
Norway +45 96 360 374
Poland  0 801 449262
Portugal 800 834 196 
Romania 0 21 210 38 09 33
Russia, Kaliningrad  0 4012631061
Slovak Republik  0 244 648 151
Spain 902 014 909
Sweden 0 13 20 14 20
The Netherlands  0 900-6664867
Ukraine 0 44 458 38 70
Country   Phone Number Country   Phone Number
 
						

							ENGLISH
CE MARKING DECLARATION OF CONFORMITY
This LCD monitor complies with the requirements of the EC Directive 89/336/EEC “EMC Directive” and 73/23/
EEC “Low Voltage Directive” as amended by Directive 93/68/EEC.
The electro-magnetic susceptibility has been chosen at a level that gives correct operation in residential areas,
business and light industrial premises and small-scale enterprises, inside as well as outside of the buildings.
All places of operation are characterised by their connection to the public low voltage power supply system.
„We reserve the right to change specifications without notice.
„All trademarks used in this user manual are the property of their respective owners.
„As an E
NERGY STAR® Partner, iiyama has determined that this product meets the ENERGY STAR® guidelines for
energy efficiency.
 
						

							ENGLISH
TABLE OF CONTENTS
FOR YOUR SAFETY..................................................................................... 1
SAFETY PRECAUTIONS........................................................................ 1
SPECIAL NOTES ON LCD MONITORS.................................................... 3
CUSTOMER SERVICE............................................................................. 3
CLEANING.............................................................................................. 3
BEFORE YOU OPERATE THE MONITOR....................................................... 4
FEATURES.............................................................................................. 4
CHECKING THE CONTENTS OF THE PACKAGE.................................... 4
FITTING AND REMOVAL OF BASE ........................................................ 5
CONTROLS AND  CONNECTORS........................................................... 6
CONNECTING YOUR MONITOR............................................................. 7
COMPUTER SETTING.............................................................................. 8
ADJUSTING THE VIEWING ANGLE ........................................................ 8
OPERATING THE MONITOR.......................................................................... 9
ADJUSTMENT MENU CONTENTS........................................................... 10
SCREEN ADJUSTMENTS........................................................................ 16
POWER MANAGEMENT FEATURE......................................................... 19
TROUBLE SHOOTING................................................................................... 20
APPENDIX..................................................................................................... 22
SPECIFICATIONS.................................................................................... 22
DIMENSIONS........................................................................................... 23
COMPLIANT TIMING................................................................................ 23
We recommend recycling of used product. Please contact your dealer or
iiyama service center. Recycle information is obtained via the Internet, using
the address:http://www.iiyama.com
You can access the Web page of different countries from there.
For disposal or recycling information, please contact your local authorities or the
Electronic Industries Alliance (www.eiae.org).
This information is only for U.S.A..
Hg
LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE
RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE OR
FEDERAL LAWS.
 
						

							ENGLISH
FOR YOUR SAFETY
WARNING
STOP OPERATING THE MONITOR WHEN YOU SENSE TROUBLE
If you notice any abnormal phenomena such as smoke, strange sounds or fumes, unplug the monitor
and contact your dealer or iiyama service center immediately. Further use may be dangerous and
can cause fire or electric shock.
NEVER REMOVE THE CABINET
High voltage circuits are inside the monitor. Removing the cabinet may expose you to the danger of
fire or electric shock.
DO NOT PUT ANY OBJECT INTO THE MONITOR
Do not put any solid objects or liquids such as water into the monitor. In case of an accident, unplug
your monitor immediately and contact your dealer or iiyama service center. Using the monitor with
any object inside may cause fire, electric shock or damage.
INSTALL THE MONITOR ON A FLAT, STABLE SURFACE
The monitor may cause an injury if it falls or is dropped.
DO NOT USE THE MONITOR NEAR WATER
Do not use where water may be splashed or spilt onto the monitor as it may cause fire or electric
shock.
OPERATE UNDER THE SPECIFIED POWER SUPPLY
Be sure to operate the monitor only with the specified power supply. Use of an incorrect voltage will
cause malfunction and may cause fire or electric shock.
PROTECT THE CABLES
Do not pull or bend the power cable and signal cable. Do not place the monitor or any other heavy
objects on the cables. If damaged, the cables may cause fire or electric shock.
ADVERSE WEATHER CONDITIONS
It is advisable not to operate the monitor during a heavy thunder storm as the continual breaks in
power may cause malfunction. It is also advised not to touch the plug in these circumstances as it
may cause electric shock.
SAFETY PRECAUTIONS
    FOR YOUR SAFETY     1
 
						

							ENGLISH
2     FOR YOUR SAFETY
CAUTION
INSTALLATION LOCATION
Do not install the monitor where sudden temperature changes may occur, or in humid, dusty or smoky
areas as it may cause fire, electric shock or damage. You should also avoid areas where the sun
shines directly on the monitor.
DO NOT PLACE THE MONITOR IN A HAZARDOUS POSITION
The monitor may topple and cause injury if not suitably located. Please also ensure that you do not
place any heavy objects on the monitor, and that all cables are routed such that children may not pull
the cables and possibly cause injury.
MAINTAIN GOOD VENTILATION
Ventilation slots are provided to keep the monitor from overheating. Covering the slots may cause
fire. To allow adequate air circulation, place the monitor at least 10 cm (or 4 inches) from any walls.
Do not remove the tilt stand when operating the monitor. Ventilation slots on the back of the cabinet
will be blocked and the monitor may overheat if the stand is removed. This may cause fire or damage.
Operating the monitor on its back, side, upside down or on a carpet or any other soft material may
also cause damage.
DISCONNECT THE CABLES WHEN YOU MOVE THE MONITOR
When you move the monitor, turn off the power switch, unplug the monitor and be sure the signal
cable is disconnected. If you do not disconnect them, it may cause fire or electric shock.
UNPLUG THE MONITOR
If the monitor is not in use for a long period of time it is recommended that it is left unplugged to avoid
accidents.
HOLD THE PLUG WHEN DISCONNECTING
To disconnect the power cable or signal cable, always pull it by the plug. Never pull on the cable itself
as this may cause fire or electric shock.
DO NOT TOUCH THE PLUG WITH WET HANDS
Pulling or inserting the plug with wet hands may cause electric shock.
WHEN YOU INSTALL THE MONITOR ON YOUR COMPUTER
Be sure the computer is strong enough to hold the weight of the monitor, otherwise, you may damage
your computer.
DO NOT PUT FLOPPY DISKS NEAR THE SPEAKERS
Magnetically recorded data, such as on a floppy disk, may become corrupted by the magnetic field
produced by the speakers if the disks are placed on or near the speakers.
ERGONOMIC RECOMMENDATIONS
To eliminate eye fatigue, do not operate the monitor against a bright background or in a dark room. For
optimal viewing comfort, the monitor should be just below eye level and 40-60 cm (16-24 inches)
away from your eyes. When using the monitor over a prolonged time, a ten minute break every hour
is recommended as looking at the screen continuously can cause eye strain.
OTHERS
 
						

							ENGLISH
The following symptoms are normal with LCD monitors and do not indicate a problem.
NOTEWhen you first turn on the LCD monitor, the picture may not fit in the display area
because of the type of computer that is used. In this case, adjust the picture
position to the correct position. „
Due to the nature of the LCD screen, an afterimage of the previous screen may
remain after switching the image, when the same image is displayed for hours. In
this case, the screen is recovered slowly by changing the image or turning off the
Power Switch for hours. „You may find slightly uneven brightness on the screen depending on the desktop
pattern you use. „
SPECIAL NOTES ON LCD MONITORS
Contact your dealer or iiyama service center for the backlight replacement when the
screen is dark, flickering or not lighting up. Never attempt to replace it by yourself. „Due to the nature of the backlight, the screen may flicker during initial use. Turn off
the Power Switch and then turn it on again to make sure the flicker disappears. „
NOTEThe fluorescent light used in the LCD monitor may have to be periodically replaced.
For the warranty coverage on this component, please check with local iiyama
service center.
If you have to return your unit for service and the original packaging has been
discarded, please contact your dealer or iiyama service center for advice or
replacement packaging. „
„
WARNINGIf you drop any materials or liquids such as water into the monitor when cleaning,
unplug the power cable immediately and contact your dealer or iiyama service center. „
CAUTIONFor safety reasons, turn off the power switch and unplug the monitor before you
clean it. „
NOTETo protect the LCD panel, do not scratch or rub the screen with a hard object.
„
Never use any of the following strong solvents. These will damage the cabinet and
the LCD screen. „
Thinner
Benzine
Abrasive cleanerSpray-type cleaner
Wax
Acid or Alkaline solvent
Touching the cabinet with any product made from rubber or plastic for a long time
may cause degeneration or loss of paint on the cabinet. „
CABINETStains can be removed with a cloth lightly moistened with a mild detergent solvent. Then
wipe the cabinet with a soft dry cloth.
LCD
SCREENPeriodic cleaning with a soft dry cloth is recommended.
Dont use tissue paper etc. because these will damage the LCD screen.
CUSTOMER SERVICE
CLEANING
    FOR YOUR SAFETY     3
 
						

							ENGLISH
4     BEFORE YOU OPERATE THE MONITOR
CAUTION*The rating of the Power Cable enclosed in 120V area is 10A/125V. If you are using
a power supply higher than this rating, then a power cable with a rating of 10A/
250V must be used.
However, all guarantees and warranties are void for any problems or damage
caused by a power cable not supplied by iiyama. „ Power Cable*„ D-Sub Signal Cable
„ Audio  Cable„ Stand (Stand-Arm,Base)
„ User Manual The following accessories are included in your package. Check to see if they are enclosed with the
monitor. If anything is missing or damaged, please contact your local iiyama dealer or regional iiyama
office.
CHECKING THE CONTENTS OF THE PACKAGE
BEFORE YOU OPERATE THE MONITOR
FEATURES
‹ ‹‹ ‹
‹48cm (19) TFT Color LCD Monitor
‹ ‹‹ ‹
‹Supports Resolutions up to 1680 × 1050
‹ ‹‹ ‹
‹High Contrast 1000:1(static), DCR function available / High Brightness 300cd/m
2
‹ ‹‹ ‹
‹Multi-Color Control
Supports sRGB International Standard
‹ ‹‹ ‹
‹Gamma Control
Clear Display for Moving Pictures & Photographs
‹ ‹‹ ‹
‹Digital Character Smoothing
‹ ‹‹ ‹
‹Automatic Set-up
‹ ‹‹ ‹
‹Stereo Speakers
2 × 1W Stereo Speakers
‹ ‹‹ ‹
‹Economy Mode
Reduced Power Consumption
‹ ‹‹ ‹
‹Plug & Play VESA DDC2B Compliant
Windows
® 95/98/2000/Me/XP/Vista Compliant
‹ ‹‹ ‹
‹Power Management (E
NERGY STAR® and VESA DPMS Compliant)
‹ ‹‹ ‹
‹VESA Mounting Standard (100mm×100mm) Compliant
 
						

							ENGLISH
BEFORE YOU OPERATE THE MONITOR     5
FITTING AND REMOVAL OF BASE
Install the stand on a stable surface. The monitor may cause injury or damage if it
falls or is dropped. „CAUTION
Do not give a strong impact to the monitor. It may cause damage.
„
Unplug the monitor before installation to avoid electric shock or damage.
„

1.Put a piece of soft cloth on the table
beforehand to prevent the monitor from
beingscratched. Lay the monitor flat on
a table with front face down.
2.Hold the monitor and push the Stand-Arm.
3.Hold the monitor and push the Stand-Base.1.Put a piece of soft cloth on the table
beforehand to prevent the monitor from
beingscratched. Lay the monitor flat on
a table with front face down.
2.Press the stopper at the bottom of the
stand and remove the Stand-Base from
the arm.
3.Press the stopper at the back of the stand
arm and remove the Stand-Arm from the
monitor.
Stand-Base
Stand-Arm
Stand-Base
Stand-Arm
Stopper
Stopper
 
						

							ENGLISH
6     BEFORE YOU OPERATE THE MONITOR
CONTROLS AND CONNECTORS
APower Switch (     )
BMenu Button (MENU)
C+ Button ( + )
D– Button ( – )
EAuto Button (AUTO)
FPower Indicator
Blue:Normal operation
Orange:Power Management
The monitor enters into power management mode which reduces the power
consumption to less than 2W when receiving no horizontal and/or vertical
sync signal.
GSpeakers
HAC Connector (AC IN)
ID-sub mini 15pin Connector (D-SUB)
JAudio Connector (AUDIO IN)
KKeyhole for Security Lock
You can fasten a security lock and cable to prevent the monitor from being removed
without your permission. 
NOTE
NOTE