Icom Ic_r20 Communications Reciever Instruction Manual

							88
17
DRIVER INSTALLATION
uThe “Found New Hardware Wizard,” will come up again to
install the USB serial port driver. 
•“Found New Hardware” appears as below.
iRepeat step wto t.
oThe following screen appears when the installation is com-
pleted. Click [Finish] to close the screen.•Rebooting the PC is recommended.
■For Microsoft
®
Windows
®
98/98SE/Me
qConnect the IC-R20 to the desired USB port using with the
USB cable, OPC-1382.
wThe “Add New Hardware Wizard” will come up as below.
Click [Next>].
Click
Click
17 
						

							89
17
DRIVER INSTALLATION
eSelect “Search for the best driver for your device. (Recom-
mended),” then click [Next>].rSelect “Specify a location,” and insert the supplied CD into
the CD drive, click [Browse] to select the CD drive, then
click [Next>].
Specifiy
Select
ClickClick
Select
Click 
						

							90
17
DRIVER INSTALLATION
17
tWhen the driver is found, the following dialog is displayed.
Click [Next>] to start the installation.
yAfter the installation is completed, click [Finish].•Rebooting the PC is recommended.
■COM port confirmationAfter the driver installation, confirm the driver availability and
the port number are recommended.
In this section, screen shots of Windows XP are used for in-
struction example. However, the instructions are similar to an-
other operating systems, Windows 98, Me and 2000.
qBoot up the Windows.
wSelect the “Control Panel” in the Start menu.•Control panel appears as shown in the next step below.eClick the “Performance and Maintenance.” •Performance and Maintenance menu appears.rClick the “System,” then click the “Hardware” tab in the dis-
played System Properties screen.
Click
ClickClick 
						

							91
17
DRIVER INSTALLATION
tClick the [Device Manager]. •Device Manager screen appears as below.
yClick “ ” of the “Ports (COM & LPT)” to display the usable
COM port and the port number.
uConfirm the USB serial port availability and the COM port
number.
iClose the Device Manager, System Properties screen and
then Control panel. 
Confirm the USB serial port availability and the COM port
number.
(In this example, the USB serial port number is “3.”)
Click
Click 
						

							q
w
iR20
■ VFO mode selection
POCKET GUIDE
Push [VFO MHz] momentarily to 
select VFO mode.➥
■ Receive mode selectionPush [MODE SCAN] several 
times to select the desired mode.➥
■ Audio level setting
Rotate [L-DIAL] (or push [Y]/ [Z]) to set the audio level.➥
■ Squelch level setting
While pushing [SQL], rotate [R-
DIAL]  to set the squelch level.➥
■ Frequency band selectionPush [BAND] several times, or 
while pushing [BAND], rotate [R-
DIAL] to select the desired fre-
quency band.
➥
■ Tuning step selectionPush [9 TS], then rotate [R-DIAL]  
to select the desired tuning step.
• Push [9 TS] again to return to the 
previous condition.
➥
■ Key lock functionPush [• LOCK]  for 1 sec. to toggle 
the key lock function ON and OFF.
• “       ” appears when the lock function 
is in use.
➥
■ Frequency setting
Push [VFO MHz] to select VFO 
mode.
Rotate 
[R-DIAL] to set the de-
sired operating frequency. 
• Entering keypad directly can be 
selected the desired frequency.
q
w ■ Memory channel selection
Push [MR S.MW] to select 
memory mode.
Rotate 
[R-DIAL] to set the de-
sired memory channel.
• Entering keypad directly can be 
selected the desired channel.
q
w
e■ Memory bank channel selectionPush [MR S.MW] to select 
memory mode.
Push [BAND] several times, or 
while pushing [BAND], rotate [R-
DIAL] to select the desired bank.Rotate [R-DIAL] to select the 
desired bank channel. ■ Attenuator function
Push [ΩΩ ATT]  to toggle the 
attenuator ON and OFF.
• “ATT” appears when the attenuator 
is in use.
➥
■ Memory mode selectionPush [MR S.MW] momentarily to 
select memory mode.➥■ Single band and dualwatch selectionPush [DUALWATCH] for 1 sec. to 
toggle between single band and 
dualwatch operation.➥
92
18
POCKET GUIDE
Important operating instructions are summed up in this and the following
page for your simple reference.
By cutting along the line and folding on the dotted line, it will become a card
sized operating guide which can easily be carried in a card case or wallet,
etc.
q Cutw Folde Complete
 
						

							q
w
e
r
■ Memory channel programming
Set the desired frequency and 
other functions in VFO mode.
Push 
[MR S.MW] for 1 sec. to 
enter the select memory write 
condition.
• 1 short and 1 long beeps sound.Rotate [R-DIAL] to select the de-
sired memory channel number.
Push [MR S.MW] for 1 sec. 
again to program the contents 
into the selected channel.
• 3 beeps sound.
q
w
e
■ Scan skip setting
Push [MR S.MW] to select 
memory mode.
Rotate [R-DIAL] to select the de-
sired memory channel.
While pushing [5 SKIP], rotate [R-DIAL] to set the skip setting 
(skip channel or skip frequen-
cy) ON and OFF.q
w
■ VFO scans
Push [VFO MHz] to select VFO 
mode.
While pushing [MODE SCAN], 
rotate [R-DIAL] to select the de-
sired scan type.
• Selectable from “ALL,” “BAND” or 
“PROG xx” (xx= 0–24). 
e
rRelease [MODE SCAN] to start 
scan.
• Rotate [R-DIAL] to change the scan-
ning direction.
• During scan, push 
[MR S.MW] to 
start auto memory write scan.
Push [DUALWATCH] to stop 
scan.q
w
■ Memory scans
Push [MR S.MW] to select 
memory mode.
• Push [BAND] to select a bank, if de-
sired.
While pushing [MODE SCAN], 
rotate [R-DIAL] to select the de-
sired scan type.
• Selectable from “ALL,” “BANK-LINK” 
or “BANK.”
e
rRelease [MODE SCAN] to start 
memory/bank scan.
• Rotate [R-DIAL] to change the scan-
ning direction.
Push [DUALWATCH] to stop 
scan.
SCAN:ALL√
SCAN:BAND√
SCAN:PROG-01√
SCAN:ALL
SCAN:BANK-LINK
SCAN:BANK 
						

							94
19
CE
19
DECLARATION
OF CONFORMITY
We Icom Inc. Japan
1-1-32, Kamiminami, Hirano-ku
Osaka 547-0003, Japan
Declare on our sole responsibility that this equipment complies with the
essential requirements of the Radio and Telecommunications Terminal
Equipment Directive, 1999/5/EC, and that any applicable Essential Test
Suite measurements have been performed.Kind of equipment: COMMUNICATIONS RECEIVERType-designation:
iR20
Version (where applicable):
This compliance is based on conformity with the following harmonised
standards, specifications or documents:i) Article 3.1a EN 60950 (1992-08)+A11:1997ii) Article 3.1b EN 301489-1 and EN 301489-15iii) Article 3.2 EN 301 783-2iv)v)
Düsseldorf 23rd Mar. 2004Place and date of issueIcom (Europe) GmbHHimmelgeister straße 100D-40225 Düsseldorf
Authorized representative nameT.Maebayashi
General ManagerSignature 
						

							1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
A-6353H-1EX-w
Printed in Japan©2004 Icom Inc.

■GER■
■FRA■ESP■SWE
■AUT■NED■POR■DEN
■GBR■BEL■ITA■FIN
■IRL■LUX■GRE■
■SUI
■ ■NOR
■ ■GER■FRA■
■ESP■
■SWE
■ ■AUT■
■NED■
■POR■
■DEN
■ ■GBR■
■BEL■
■ITA■
■FIN
■ ■IRL■
■LUX■
■GRE■
■SUI
■ ■NOR
#02 Europe
#03 U.K.
#07 France