Icom Ic_r20 Communications Reciever Instruction Manual

88
17
DRIVER INSTALLATION
uThe “Found New Hardware Wizard,” will come up again to
install the USB serial port driver. 
•“Found New Hardware” appears as below.
iRepeat step wto t.
oThe following screen appears when the installation is com-
pleted. Click [Finish] to close the screen.•Rebooting the PC is recommended.
■For Microsoft
®
Windows
®
98/98SE/Me
qConnect the IC-R20 to the desired USB port using with the
USB cable, OPC-1382.
wThe “Add New Hardware Wizard” will come up as below.
Click [Next>].
Click...

89
17
DRIVER INSTALLATION
eSelect “Search for the best driver for your device. (Recom-
mended),” then click [Next>].rSelect “Specify a location,” and insert the supplied CD into
the CD drive, click [Browse] to select the CD drive, then
click [Next>].
Specifiy
Select
ClickClick
Select
Click 

90
17
DRIVER INSTALLATION
17
tWhen the driver is found, the following dialog is displayed.
Click [Next>] to start the installation.
yAfter the installation is completed, click [Finish].•Rebooting the PC is recommended.
■COM port confirmationAfter the driver installation, confirm the driver availability and
the port number are recommended.
In this section, screen shots of Windows XP are used for in-
struction example. However, the instructions are similar to an-
other operating systems, Windows 98, Me and...

91
17
DRIVER INSTALLATION
tClick the [Device Manager]. •Device Manager screen appears as below.
yClick “ ” of the “Ports (COM & LPT)” to display the usable
COM port and the port number.
uConfirm the USB serial port availability and the COM port
number.
iClose the Device Manager, System Properties screen and
then Control panel. 
Confirm the USB serial port availability and the COM port
number.
(In this example, the USB serial port number is “3.”)
Click
Click 

q
w
iR20
■ VFO mode selection
POCKET GUIDE
Push [VFO MHz] momentarily to 
select VFO mode.➥
■ Receive mode selectionPush [MODE SCAN] several 
times to select the desired mode.➥
■ Audio level setting
Rotate [L-DIAL] (or push [Y]/ [Z]) to set the audio level.➥
■ Squelch level setting
While pushing [SQL], rotate [R-
DIAL]  to set the squelch level.➥
■ Frequency band selectionPush [BAND] several times, or 
while pushing [BAND], rotate [R-
DIAL] to select the desired fre-
quency band.
➥
■ Tuning step...

q
w
e
r
■ Memory channel programming
Set the desired frequency and 
other functions in VFO mode.
Push 
[MR S.MW] for 1 sec. to 
enter the select memory write 
condition.
• 1 short and 1 long beeps sound.Rotate [R-DIAL] to select the de-
sired memory channel number.
Push [MR S.MW] for 1 sec. 
again to program the contents 
into the selected channel.
• 3 beeps sound.
q
w
e
■ Scan skip setting
Push [MR S.MW] to select 
memory mode.
Rotate [R-DIAL] to select the de-
sired memory channel.
While pushing [5...

94
19
CE
19
DECLARATION
OF CONFORMITY
We Icom Inc. Japan
1-1-32, Kamiminami, Hirano-ku
Osaka 547-0003, Japan
Declare on our sole responsibility that this equipment complies with the
essential requirements of the Radio and Telecommunications Terminal
Equipment Directive, 1999/5/EC, and that any applicable Essential Test
Suite measurements have been performed.Kind of equipment: COMMUNICATIONS RECEIVERType-designation:
iR20
Version (where applicable):
This compliance is based on conformity with the...

1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
A-6353H-1EX-w
Printed in Japan©2004 Icom Inc.

■GER■
■FRA■ESP■SWE
■AUT■NED■POR■DEN
■GBR■BEL■ITA■FIN
■IRL■LUX■GRE■
■SUI
■ ■NOR
■ ■GER■FRA■
■ESP■
■SWE
■ ■AUT■
■NED■
■POR■
■DEN
■ ■GBR■
■BEL■
■ITA■
■FIN
■ ■IRL■
■LUX■
■GRE■
■SUI
■ ■NOR
#02 Europe
#03 U.K.
#07 France