Icom Ic-r5 Communications Reciever Instruction Manual

20
5
MEMORY CHANNELS
New2001
5
Selecting display typeDuring memory mode operation, one of the programmed
memory name, bank name or the channel number can be dis-
played instead of the frequency for your preference.
qPush [V/M•S.MW•~] to select memory mode.•[BAND•] to select the desired bank group.wWhile pushing [FUNC], push [BAND•] to select display
type from frequency, bank name, memory name and chan-
nel number indications.
D D
Selecting bank channel indicationDuring bank channel operation, the bank...

21
5
MEMORY CHANNELS
New2001

Copying memory contents
This function transfers a memory channel’s contents to VFO
(or another memory channel). This is useful when searching
for signals around a memory channel frequency and for re-
calling the offset frequency, subaudible tone frequency etc.DMemory➪VFOqSelect the memory channel to be copied.
➥Push [V/M•S.MW•~] to select memory mode, then ro-
tate [DIAL] to select the desired memory channel.
•Select the bank channel with [BAND•] and [DIAL], if de-
sired....

22
5
MEMORY CHANNELS
New2001
5
Memory clearingContents of programmed memories can be cleared (blanked),
if desired.
qPush [V/M•S.MW•~] for 1 sec. to select select memory
write condition.
•1 short and 1 long beeps sound.
•“ ” indicator and memory channel number blink.
•Do not hold [V/M•S.MW•~] for more than 2 sec. otherwise the
memory contents will be copied to VFO.
wRotate [DIAL] to select the desired memory channel to be
cleared.
eWhile pushing [MODE•SCAN], rotate [DIAL] to select
“CLEAR.”
•After...

23
5
MEMORY CHANNELS
New2001

Transferring memory contents
Contents of programmed memory channels can be trans-
ferred to another memory. 
qPush [V/M•S.MW•~] for 1 sec. to enter select memory
write condition.
•1 short and 1 long beeps sound.
•“ ” indicator and memory channel number blink.
•Do not hold [V/M•S.MW•~] for more than 2 sec. otherwise the
memory contents will be copied to VFO.
wRotate [DIAL] to select the desired memory channel to be
transferred.
eWhile pushing [MODE•SCAN], rotate [DIAL] to...

24
5
MEMORY CHANNELS
New2001
5
Erasing/transferring bank contentsContents of programmed memory channels can be or trans-
ferred to another memory.
INFORMATION:Even if the memory bank contents are
cleared, the memory channel contents still remain pro-
grammed.
qSelect the desired bank contents to be transferred or
erased from the bank.
➥Push [V/M•S.MW•~] to select memory mode.
➥While pushing [BAND•], rotate the [DIAL] to select
the desired memory bank group.
➥Rotate [DIAL] to select the bank channel....

25
SCAN OPERATION
New2001
6Scan typesScanning searches for signals automatically and makes it
easier to locate new stations for contact or listening purposes.There are 7 scan types and 4 resume conditions to suit your
operating needs.FULL SCAN 
(p. 26)Repeatedly scans all frequen-
cies over the entire band. 
Some frequency ranges are
not scanned according to the
frequency coverage of the re-
ceiver’s version.
150
kHz1303.995
MHz
Scan
Jump
SELECTED BAND SCAN(p. 26)Repeatedly scans all frequen-
cies over...

26
6
SCAN OPERATION
New2001
6
Full/band/programmed scan qSelect VFO mode with [V/M•S.MW•~].
•Select the desired frequency band with [BAND•], if desired.
wSet the squelch to the point where noise is just muted.
ePush [MODE•SCAN] for 1 sec. to enter scanning type se-
lection condition.
rRotate [DIAL] to select the desired scanning type.
•“ALL” for full scan; “BAND” for band scan, “PROGxx” for pro-
grammed scan (xx= 0 to 24; programmed scan edges numbers
only displayed)
tTo start the scan, push...

27
6
SCAN OPERATION
New2001
Scan edges programmingScan edges can be programmed in the same manner as
memory channels. Scan edges are programmed into scan
edges, 00A/00B to 24A/24B, in memory channels.
qPush [V/M•S.MW•~] to select VFO mode.
wSet the desired frequency:
➥Select the desired band with [BAND•].
➥Set the desired frequency with [DIAL].
➥Set other data 
(e.g. offset frequency, duplex direction, tone
squelch, etc.)
, if desired.
ePush [V/M•S.MW•~] for 1 sec. to select select memory
write...

28
6
SCAN OPERATION
New2001
6
Memory/bank/all bank scan qSelect memory mode with [V/M•S.MW•~].
•Select the desired bank with [BAND•] for bank scan.
wSet the squelch to the point where noise is just muted.
ePush [MODE•SCAN] for 1 sec. to;
• When memory mode is selected at the step 
q q:
- start memory scan.
• When a bank channel is selected at the step q q:
- enter scan type selection mode.
rRotate [DIAL] to select the desired scanning type.
•“ALL” for all bank scan; “BANK” for bank scan.
tPush...

29
6
SCAN OPERATION
New2001
Auto memory write scanThis scan is useful for searching a specified frequency range
and automatically storing busy frequencies into memory
channels. The same frequency ranges used for program scan
are used for auto memory write scan.
qSelect VFO mode with [V/M•S.MW•~].
wPush [MODE•SCAN] for 1 sec. to enter scanning type se-
lection condition.
eRotate [DIAL] to select the desired scanning type.
•“ALL” for full scan; “BAND” for band scan, “PROGxx” for pro-
grammed scan (xx= 0 to...