Icom Ic-r3 Communications Reciever Instruction Manual

							OPERATING GUIDE
iR3BASIC OPERATIONqPush [POWER] for 2 sec.
wPush [↕] to set the desired audio
level.
eSelect VFO mode with [V/M].
rSelect the desired band with [↔].
tRotate [DIAL] to change the fre-
quency.
•The frequency changes according to
the preset tuning steps.
ySet the squelch level.
•While pushing [SQL], rotate [DIAL].
•The first click of [DIAL] indicates the
current squelch level.
•“LEVEL1”is loose squelch and
“LEVEL9”is tight squelch.•“AUTO”indicates automatic level ad-
justment.
tWhen a signal is received:
•Squelch opens and audio is emitted
from the speaker.
•The S/RF indicator shows the relative
signal strength.
◊Using the dial select step(p. 39)
Rotate [DIAL] while pushing [FUNC]
to change the frequency in 100 kHz,
1 MHz or 10 MHz steps.DUPLEX OPERATIONqSet the receive station frequency
(e.g. repeater output frequency).
wSet the shift direction of the trans-
mit station frequency in set mode.
(–DUP or DUP)
ePush and hold [SQL] to monitor
the transmit station’s frequency.◊Tone scan(p. 30)
Push [FUNC] + [↔] for 2 sec. to start
the tone scan.

MEMORY CHANNEL SELECTION
qPush [V/M] to select memory
mode.
•“M:”or “X”appears.
wSelect a memory channel with
[DIAL].
eRotate [DIAL] while pushing
[FUNC] to select the memory
bank.MEMORY CLEARqSelect the desired memory chan-
nel.
wSelect VFO mode with [V/M] and
push [V/M] for 1 sec. to indicate
the channel.
ePush [FUNC] + [V/M] for 2 sec.
Important operating instructions are summed up in this and the following page
for your simple reference.
By cutting along the line and folding on the dotted line, it will become a card
sized operating guide which can easily be carried in a card case or wallet,
etc.
q Cutw Folde Complete

57
19QUICK REFERENCE 
						

							58
19QUICK REFERENCE
SCAN◊Full/band/programmed scan
qSelect VFO mode with [V/M].
wMake sure the squelch is set to
the threshold point.
ePush [↔] for 2 sec. to start the
scan.
•Rotate [DIAL] while pushing [↔] to
select scan edge, if desired.
•To change the scanning direction, ro-
tate [DIAL].
rPush [↔] again to stop the scan.
◊Memory (bank) scan
qSelect memory mode with [V/M].
wMake sure the squelch is set to
the threshold point.
ePush [↔] for 2 sec. to start the
scan.
•Rotate [DIAL] while pushing [↔] to
turn memory bank scan ON or OFF,
if desired.
rPush [↔] again to stop the scan.SET MODEqPush [FUNC] + [(MODE) SET]
momentarily to enter set mode.
•Select non-band scope screen in ad-
vance for color LCD.
wRotate [DIAL] to select a display.
ePush [↔] or rotate [DIAL] while
pushing [FUNC] to set the condi-
tion.
rPush [
(MODE)
SET] to exit set
mode.
LOCK FUNCTIONPush [FUNC] + [(MODE) SET] for 2
sec. to toggle the lock function ON or
OFF. (p. 9)
CPU RESETTING◊Partial resetting(p. 45)
While pushing [FUNC] and [V/M],
turn power on to partially reset the
receiver.•Partial resetting does not clear the mem-
ory channel contents.◊Total resetting(p. 45)
While pushing [FUNC], [V/M] and
[MODE], turn power on to reset the
receiver.
Caution:
Resetting the receiver
initializes all memory contents. 
						

							DECLARATION
OF CONFORMITY
We Icom Inc. Japan6-9-16, Kamihigashi, Hirano-ku
Osaka 547-0002, Japan
Type-designation:       
iC-r3
Version (where applicable): Kind of equipment:     
COMMUNICATIONS RECEIVER
This compliances is based on conformity with the following harmonised
 standards, specifications or documents:
i)   
EN 60950ii)  prEN 301 489-1
iii) prEN 301 489-15
iv) prEN 301 783-2
v)
Signature Authorized representative name Place and date of issue
T. Aoki
General Manager Icom (Europe) GmbH
Himmelgeister straße 100
D-40225 Düsseldorf
Düsseldorf 11. July. 2000
Icom (Europe) GmbH
Declare on our sole responsability that this equipment complies the
essential requirements of the Radio and Telecommunications Terminal 
Equipment Directive, 1999/5/CE. 
						

							Count on us!
6-9-16 Kamihigashi, Hirano-ku, Osaka 547-0002 Japan
A-5653H-1EX-w
Printed in Japan
© 2000 Icom Inc.