Icom Ic-703 Hf/50mhz All Mode Tranciever Instruction Manual
Here you can view all the pages of manual Icom Ic-703 Hf/50mhz All Mode Tranciever Instruction Manual. The Icom manuals for Communications receiver are available online for free. You can easily download all the documents as PDF.
Page 21
6 1PANEL DESCRIPTION DS1 functions MEMORY WRITE (p. 57) Push for 1 sec. to store the selected readout frequency and operating mode into the displayed memory channel. MEMO PAD WRITE (p. 60) Push to store the the selected readout frequency and operating mode into a memo pad. MEMO PAD READ (p. 60) Push to call up a memo pad. DS2 functions DURING VFO MODE: DURING MEMORY MODE: SCAN (pgs. 61–63) Push to start or stop the scan function. PRIORITY WATCH (p. 63) Push to start or stop the priority watch....
Page 22
7 1PANEL DESCRIPTION Rear panel qANTENNA CONNECTOR [ANT] (p. 13) Accepts a 50 Ωantenna with a PL-259 connector. wGROUND TERMINAL [GND] (p. 11) Connect this terminal to a ground to prevent electri- cal shocks, TVI, BCI and other problems. eDATA SOCKET [DATA] (pgs. 8, 14) 6-pin min DIN socket to connect a TNC (Terminal Node Controller), etc. for packet operation. • See page at right for socket information. rACCESSORY SOCKET [ACC] (pgs. 8, 14) Enables connection to external equipment such as a TNC for data...
Page 23
8 1PANEL DESCRIPTION DDATA socket DACC socket ACCPIN No.NAME DESCRIPTION SPECIFICATIONS 1 2 3 4 8765 9 10 11 12 13 Rear panel view qbrownigray wredowhite eorange!0black ryellow!1pink tgreen!2light blue yblue upurple!3light green 1 8 V Regulated 8 V output.Output voltage : 8 V ±0.3 V Output current : Less than 10 mA 2 GND Connects to ground. ——— Input/output pin. (HF/50 MHz only)Ground level : –0.5 V to 0.8 V 3 HSENDGoes to ground when transmitting. Output current : Less than 20 mA When grounded,...
Page 24
9 1PANEL DESCRIPTION Function display qNARROW/WIDE FILTER INDICATORS ➥“ã” appears when selecting AM narrow or FM narrow modes. ➥When installing an optional narrow filter, narrow mode can be selected in CW, RTTY and SSB modes. • When the SSB wide filter is installed, “ç” appears during wide mode selection. wMODE INDICATORS Show the selected operating mode. •“å” appears when CW reverse or RTTY reverse mode is selected. eSPLIT INDICATOR Appears during split operation. rPROGRAMMABLE/1 MHz TUNING STEP...
Page 25
10 1PANEL DESCRIPTION •MICROPHONE CONNECTOR Microphone (HM-103) qUP/DOWN SWITCHES [UP]/[DN] Change the operating frequency. • Push and hold to change the frequency continuously. • Tuning step is 50 Hz when no TS indicator appears. wLOCK SWITCH [LOCK] Locks the [UP]/[DN] switches. ePTT SWITCH [PTT] Push and hold to transmit; release to receive. DN UPLOCK OFF ON q we TECHNICAL INFORMATION PIN NO.FUNCTIONDESCRIPTION 1+8 V DC outputMax. 10 mA 2Frequency upGround Frequency downGround through 470 Ω 8Squelch...
Page 26
2 11 INSTALLATION AND CONNECTIONS Unpacking After unpacking, immediately report any damage to the delivering carrier or dealer. Keep the shipping cartons. For a description and a diagram of accessory equip- ment included with the IC-703, see ‘Supplied acces- sories’ on p. ii of this manual. Selecting a location Select a location for the transceiver that allows ade- quate air circulation, free from extreme heat, cold, or vibrations, and away from TV sets, TV antenna ele- ments, radios and other...
Page 27
2 12 INSTALLATION AND CONNECTIONS To raise the stand: With the transceiver upside down, pull the stand to- wards the rear panel and then upwards, as illus- trated below. Installation DSingle body mountingDStand Nut Spring washer Flat washer *CAUTION: Non-supplied screws (longer than 8 mm) may damage the internal units. MB-62 (optional) Supplied with the MB-62* Pull backthen up DFront panel separation DFront panel mounting qWhile pulling the panel release button towards you, slide the front panel to...
Page 28
13 2INSTALLATION AND CONNECTIONS Required connections BAND BAND MODE TS DISPLAY LOCK F 1 F 2 F 3 AF RF SQL RIT SHIFT M-CHSUB PHONESTUNER P.AMP AT T Y Z POWER MENU TX RX MICROPHONE (p. 10) HF/50 MHz ANTENNAGROUND (p. 11) HM-103 CW KEY (p. 28) Use the heaviest gauge wire or strap available and make the connection as short as possible. Grounding prevents electrical shocks, TVI and other problems. Connects to DC 9.0–15.8 V power supply. See p. 15 for details.
Page 29
14 2INSTALLATION AND CONNECTIONS Advanced connections BAND BAND MODE TS DISPLAY LOCK F 1 F 2 F 3 AF RF SQL RIT SHIFT M-CHSUB PHONESTUNER P.AMP AT T Y Z POWER MENU TX RX OPC-589 (p. 92) DESKTOP(p. 91) MICROPHONE Selectable with the [PHONE/SPEAKER] switch on the back of the front panel.SPEAKER ACC SOCKET (p. 8) DATA SOCKET (p. 8) 6-pin mini DIN socket to connect to a TNC, etc. for packet operation. AH-4 (p. 16) AH-2b EXTERNAL SPEAKER (p. 91) HEADPHONES SP-7/SP-10SM-20 or REMOTE (p. 71) Used for...
Page 30
Use a 13.8 V DC power supply with at least 3 A ca- pacity. when operating IC-703 with AC power. Refer to the diagram below for connection. CAUTION: Before connecting the DC power cable, check the following important items. Make sure: • The [POWER] switch is OFF.• Output voltage of the power source is 9.0–15.8 V when you use a non-Icom power supply. • DC power cable polarity is correct. Red: positive (+) terminal, Black: negative (–) terminal DC Power supply connections 15 2INSTALLATION AND...