Icom Ic-703 Hf/50mhz All Mode Tranciever Instruction Manual
Here you can view all the pages of manual Icom Ic-703 Hf/50mhz All Mode Tranciever Instruction Manual. The Icom manuals for Communications receiver are available online for free. You can easily download all the documents as PDF.
Page 11
VI QUICK REFERENCE GUIDE D D What are you hearing? Stop and focus on what you are hearing. Do you hear a lot of noise? Is the signal intelligible? Are you set up for the right mode? How about the filters? 1. Verify mode Your IC-703 has many features to reduce QRM and QRN from the desired signal. a. Noise Reduction:The noise reduction system on your IC-703 is part of the DSP. This is used to re- duce the hiss and QRM levels. qSelect S4(DSP menu). • Push [DISPLAY] once or twice to select S. • Push [MENU]...
Page 12
VII QUICK REFERENCE GUIDE c. Automatic Notch:The automatic notch will track up to heterodynes. This is helpful for eliminating annoying transmitter “tune up” tones on any band, and to minimize continuous tone “heterodynes” en- countered on the 40 meter phone bands at night, for example. Once selected an icon will appear “ANF” on the display. qSelect S4. • Push [DISPLAY] once or twice to select S. • Push [MENU] one or more times to select S4. wPush [(F-1)ANF] to activate the automatic notch fil- ter....
Page 13
VIII QUICK REFERENCE GUIDE f. Filter: One optional filter can be installed in the IC-703. Narrow filters help reject interference from adjacent signals and obtain good selectivity. Wide filters provide improved audio for SSB opera- tion when no interfering signals are present. Narrow filters for AM/FM modes are standard. FILTER PRESETTING: After you install a filter (see p. 87 for installation), you must specify the installed filter in initial set mode (item “22 OPT. FIL” ; see p. 79). FILTER ON/OFF: qSelect...
Page 14
IX QUICK REFERENCE GUIDE 1. Setting up your Mic Gain Microphone gain must be adjusted properly so that your signal does not distort when transmitted. qSelect SSB or another phone mode (AM or FM mode). w Push [DISPLAY] for 1 sec. to select quick set mode. ePush [MENU] one or more times to select “Q2 MIC GAIN.” • The ALC meter is selected automatically when operat- ing in SSB mode. rWhile speaking into the microphone, rotate the main dial to adjust the microphone gain so that the ALC meter does not peak...
Page 15
X QUICK REFERENCE GUIDE The IC-703 has a built-in, low distortion speech com- pressor circuit. This circuit increases your average talk power in SSB mode and is especially useful for DX’ing when the receiving station is having difficulty copying your signal. qSelect USB or LSB mode. wSelect the ALC meter. • Push [DISPLAY] once or twice to select M. • Push [MENU] one or more times to select M3, then push [ (F-3)MET] one or more times to select “ALC.” eSelect M4. • Push [MENU] one more time to select M4....
Page 16
1 1 PANEL DESCRIPTION Front panel qPOWER SWITCH [POWER] (p. 17) ➥While transceiver’s power is OFF: Push to turn power ON. • Turn the DC power supply ON in advance. ➥While transceiver’s power is ON: ❍Push momentarily to indicate the connected power supply voltage. ❍Push for 1 sec. to turn power OFF. wAF GAIN CONTROL [AF] (inner control; p. 17) Varies the audio output level from the speaker. eRF GAIN CONTROL/SQUELCH CONTROL [RF/SQL] (outer control; p. 24) Adjusts the RF gain and squelch threshold level....
Page 17
2 1PANEL DESCRIPTION rFUNCTION DISPLAY Shows the operating frequency, dot matrix indica- tions, selected memory channel, etc. See p. 9 for details. tTUNING STEP SWITCH [TS] (pgs. 19–21) ➥While in SSB/CW/RTTY modes, push momentar- ily to turn the programmable tuning step ON and OFF. While in FM/AM mode push momentarily to toggle the programmable tuning step and 1 MHz quick tuning step. • While the programmable tuning step indicator is dis- played, the frequency can be changed in programmed kHz steps....
Page 18
3 1PANEL DESCRIPTION !6RIT/SUB DIAL SWITCH [RIT/SUB] (pgs. 21, 47) ➥Push to toggle the RIT or SUB DIAL function ON and OFF—initial set mode is used to select the desired action*. • Lights green when the SUB DIAL function is ON; lights red when the RIT function is ON. • Use the [M-CH] control to vary the RIT frequency or SUB DIAL frequency (see below). ➥When the RIT function is ON, push for 1 sec. to add or subtract the shifted frequency to the oper- ating frequency. *Even if RIT is selected in initial...
Page 19
4 1PANEL DESCRIPTION Multi-function switches DM1 functions SPLIT OPERATION (p. 30) ➥Push momentarily to toggle the split func- tion ON and OFF. (p. 51) •“ä”appears when the split function is ON. ➥Push for 1 sec. to turn the quick split func- tion ON. (p. 52) • The offset frequency must be programmed in advance using initial set mode. (p. 80) • The offset frequency is shifted from the dis- played frequency. • The quick split function can be turned OFF using initial set mode. (p. 79) VFO A/B SELECTION...
Page 20
5 1PANEL DESCRIPTION METER SELECTION(p. 52) Selects the type of meter displayed (dur- ing transmit) in the function display. • Power, ALC or SWR metering can be se- lected. • Only an S-meter is available for receive. DM4 functions DURING SSB/AM OPERATION: DURING CW OPERATION: DURING RTTY OPERATION: DURING SSB-D OPERATION: DURING FM OPERATION: VOX FUNCTION (p. 53) ➥Push momentarily to toggle the VOX func- tion ON and OFF. • “VOX” appears when the VOX function is ON. ➥Push for 1 sec. to enter the VOX set...