IBM Thinkpad I Series 12001300 Manual

1171–7GJ, 1171–9WF, 1171–5YU, 1171–6WU, 1171-5WU,
1171-7WU, 1171-5BU, 1171-5WJ, 1171-6LU, 1171-52J,
1171-62J, 1171-7WJ. Some of the keys do not work if
proper device drivers and utilities are not installed.
Fn key Function
Fn+F4 Sleep button
Fn+F7 Switch display output location.
Fn+F9 Skip Track Backward
Fn+F10 Skip Track Forward
Fn+F11 Play/Pause
Fn+F12 Stop
Fn+PageUp Volume Up
Fn+PageDown Volume Down
Fn+Backspace Volume Mute
Fn+Home Brightness up
Fn+End Brightness down
Fn+Insert/Delete Contrast...

1. Save all files and shut down the desktop.
2. Turn off the computer.
3. Turn on the computer. Quickly pressF11when this
message is displayed on the screen: ...″To start the
Product Recovery Program, press F11″...This message
is displayed for only a few seconds.
Note:If this message does not appear, you can use a
Recovery Repair diskette to get access to the
Product Recovery program. (see“To create a
recovery repair diskette”on page 33 for
instructions of making the Recovery Repair
diskette).
4. From...

7. If the hard disk drive is blank, a menu will appear
stating″Your computer originally included a Product
Recovery program...Reinstall the Product Recovery
program? (Y/N)
To install Service Partition, go to step 4.
To preload hard disk drive without installing Service
Partition, press″N″.
8. If a menu appears asking which operating system to
install, highlight proper operating system and press
″ENTER″.
9. A menu will appear stating″Full Recovery:″. Press
″ENTER″to select.
10. Enter″Y″at the three...

Checkout guide
Use the following procedure as a guide for computer
problems.
Note:The diagnostic tests are intended to test only IBM
products. Non-IBM products, prototype cards, or
modified options can give false errors and invalid
system responses.
1. Obtain the failing symptoms in as much detail as
possible.
2. Verify the symptoms by attempting to recreate the
failure by running the diagnostic test or by repeating
the same operation.
Testing the computer
The ThinkPad computer has a test program called...

If the error recurs, replace the FRU that caused the
error.
Note:With some FRUs, especially the system board,
the problem may be caused by peripheral
FRUs. Verify that each peripheral FRU, such as
the flexible cable, has no problem by doing the
following:
a. Replace each peripheral FRU one at a time,
and run the test again.
b. If the peripheral FRUs have no problem,
replace the main FRU itself.
To see the FRU structure of each model,
refer to“Product overview”on page 95.
6. To exit the test,...

cannot properly communicate with the Access Point
to test the device, and will report failure.
Due to the nature of wireless connection, the test
may report failure with″No LinkTest response
received″error message in the log, even if the
device is working properly. When the test failed with
this error, please repeat the test for a few times.
The device may be working properly unless the
same error persists.
Related service information
PC-Doctor can detect the following system information:
Hardware Info:...

2. Remove the battery pack.
3. Connect the AC Adapter.
4. Check that power is supplied when you power on the
computer.
5. Power off the computer.
6. Disconnect the AC Adapter and install the charged
battery pack.
7. Check that power is supplied by the battery pack when
you power on the computer.
If you suspect a power problem, refer the appropriate
power supply check listed below:
v“Checking the AC Adapter”
v“Checking operational charging”on page 38
v“Checking the Battery ASM”on page 38
Checking the AC...

Note:An audible noise from the AC Adapter does not
always indicate a defect.
Checking operational chargingTo check operational charging, use a discharged battery
pack (Battery ASM) or a Battery ASM that has less than
50% of the total power remaining when installed in the
computer.
Perform operational charging. If the battery status indicator
or icon does not turn on, remove the Battery ASM and let it
return to room temperature. Reinstall the Battery ASM. If
the charge indicator or icon still does not...

Terminal (NiMH) Signal / Voltage (V dc)
5 Thermal
6 BT+SENSE
7 BT+ (0 V. - 14.4 V.)
Terminal (Li-Ion) Signal / Voltage (V dc)
1 Ground
2 BT-SENSE
3 BT-SCLK
4 BT-SDATA
5 Thermal
6 BT+SENSE
7 BT+ (0 V. - 16.8 V.)
Note:Signal lines, not used in these steps, are used
for communications between the system and the
battery.
3. First, discharge the battery, until the voltage is less
than 9.6V (NiMH) or 14.4V (Li-Ion). Then, charge the
battery for 30 minutes. Now, check the voltage. If the
voltage is still less...

Symptom-to-FRU Index
The Symptom-to-FRU Index lists the symptoms and errors
and the possible causes. The most likely cause is listed
first.
Note:Perform the FRU replacement or actions in the
sequence shown in the FRU/Action columns. If a
FRU does not solve the problem, put the original
part back in the computer. Do not replace a
non-defective FRU.
This index can also be used to help you decide which
FRUs should be available when servicing a computer.
Numeric error codes show the errors detected in POST...