IBM C400 Projector User Manual

							Item
 
Description
 
IP
 
Address
 
State
 
Press
 
the
 
cursor
 
left/right
 
button
 
to
 
choose
 
between
 
Static
 
and
 
DHCP
 
settings.
 
In
 
Static,
 
the
 
user
 
can
 
enter
 
IP
 
Address,
 
Subnet
 
Mask,
 
Default
 
Gateway,
 
and
 
DNS
 
Server.
 
In
 
DHCP,
 
the
 
projector
 
will
 
have
 
IP
 
Address,
 
Subnet
 
Mask,
 
Default
 
Gateway,
 
and
 
DNS
 
Server
 
set.
 
Note:
 
The
 
default
 
setting
 
is
 
DHCP.
 
IP
 
Address
 
Press
 
the
 
cursor
 
up/down
 
button
 
to
 
change
 
the
 
IP
 
Address.
 
Note:
 
The
 
IP
 
address
 
can
 
only
 
be
 
changed
 
when
 
the
 
IP
 
Address
 
State
 
is
 
Static.
 
Subnet
 
Mask
 
Press
 
the
 
cursor
 
up/down
 
button
 
to
 
change
 
the
 
Subnet
 
Mask.
 
Note:
 
The
 
Subnet
 
Mask
 
can
 
only
 
be
 
changed
 
when
 
the
 
IP
 
Address
 
State
 
is
 
Static.
 
Default
 
Gateway
 
Press
 
the
 
cursor
 
up/down
 
button
 
to
 
change
 
the
 
Default
 
Gateway.
 
Note:
 
The
 
Default
 
Gateway
 
can
 
only
 
be
 
changed
 
when
 
the
 
IP
 
Address
 
State
 
is
 
Static.
 
DNS
 
Server
 
Press
 
the
 
cursor
 
up/down
 
button
 
to
 
change
 
the
 
DNS
 
Server
 
address.
 
Note:
 
The
 
DNS
 
Server
 
can
 
only
 
be
 
changed
 
when
 
the
 
IP
 
Address
 
State
 
is
 
Static.
 
Apply
 
Settings
 
Select
 
this
 
to
 
save
 
and
 
apply
 
the
 
settings.
  
Chapter
 
5.
 
On-Screen
 
Display
 
menu
 
controls
 
5-9 
						

							5-10
 
IBM
 
C400
 
PROJECTOR:
 
User ’s
 
Guide 
						

							Chapter
 
6.
 
Remote
 
network
 
operation
 
When
 
connected
 
to
 
a
 
Local
 
Area
 
Network
 
(LAN)
 
by
 
means
 
of
 
the
 
RJ-45
 
connector,
 
the
 
projector
 
can
 
be
 
controlled
 
remotely
 
through
 
a
 
We b
 
browser
 
by
 
any
 
of
 
the
 
clients
 
(PCs
 
connected
 
to
 
the
 
LAN)
 
on
 
the
 
LAN.
 
The
 
projector
 
can
 
also
 
be
 
accessed
 
outside
 
the
 
LAN,
 
provided
 
a
 
firewall
 
is
 
configured
 
accordingly.
    
 
Note:
 
 
The
 
factory
 
default
 
is
 
set
 
to
 
DHCP
 
for
 
the
 
projector.
 
Yo u
 
can
 
see
 
the
 
current
 
IP
 
address
 
in
 
the
 
Information
 
menu.
 
Remote
 
interface
 
overview
 
The
 
following
 
shows
 
the
 
remote
 
interface
 
main
 
screens.
  
©
 
Copyright
 
IBM
 
Corp.
 
2004
 
6-1  
						

							v
   
 
Remote:
 
This
 
screen
 
shows
 
the
 
current
 
status
 
of
 
the
 
projector.
  
 
 
 
v
 
 
 
Remote-2:
 
This
 
screen
 
is
 
used
 
to
 
control
 
the
 
projector.
  
 
 
   
6-2
 
IBM
 
C400
 
PROJECTOR:
 
User ’s
 
Guide 
						

							v
   
 
Administrator
 
Settings:
 
This
 
screen
 
allows
 
the
 
administrator
 
to
 
set
 
a
 
password
 
and
 
limit
 
the
 
connections
 
to
 
the
 
projector.
  
 
 
 
v
 
 
 
IP
 
Settings:
 
This
 
screen
 
allows
 
the
 
IP
 
address
 
to
 
be
 
set
 
for
 
static
 
or
 
DHCP.
  
 
 
 
v
 
 
 
E-mail
 
settings:Status
 
messages
 
for
 
the
 
projector
 
can
 
be
 
e-mailed
 
to
 
the
 
administrator
 
or
 
any
 
other
 
address.
 
Some
 
servers
 
require
 
a
 
sender
 
address,
 
otherwise
 
the
 
e-mail
 
is
 
blocked.
 
So,
 
in
 
most
 
cases
 
the
 
Sender
 
and
 
Receiver
 
addresses
 
will
 
be
 
the
 
same.
   
Chapter
 
6.
 
Remote
 
network
 
operation
 
6-3 
						

							The
 
projector
 
automatically
 
e-mails
 
status
 
messages
 
such
 
as
 
IP
 
address
 
and
 
Power
 
state
 
to
 
the
 
Receiver
 
address.
 
The
 
projector
 
cannot
 
receive
 
e-mails.
    
 
Setting
 
up
 
remote
 
operation
 
Yo u
 
should
 
know
 
some
 
or
 
all
 
of
 
the
 
following
 
address
 
settings:
 
v
 
 
 
IP
 
Address
 
v
 
 
 
Subnet
 
Mask
 
v
 
 
 
Default
 
Gateway
 
v
 
 
 
DNS
 
Server
 
v
 
 
 
E-mail
 
address
 
for
 
remote
 
PC
 
v
 
 
 
Password
 
(if
 
required)
 
for
 
remote
 
PC
 
v
 
 
 
Outgoing
 
server
 
(SMTP)
 
for
 
remote
 
PC
Note:
   
Using
 
a
 
proxy
 
server
 
for
 
your
 
LAN
 
may
 
filter
 
messages
 
from
 
the
 
projector.
 
Disable
 
the
 
proxy
 
server
 
to
 
prevent
 
this.
  
6-4
 
IBM
 
C400
 
PROJECTOR:
 
User ’s
 
Guide 
						

							The
 
factory
 
default
 
is
 
set
 
to
 
DHCP
 
for
 
the
 
projector.
 
Yo u
 
can
 
see
 
the
 
current
 
IP
 
address
 
in
 
the
 
Information
 
menu.
    
 
Yo u
 
can
 
change
 
the
 
settings
 
in
 
the
 
Network
 
Setting
 
menu.
 
To
 
access
 
the
 
Network
 
Setting
 
menu,
 
follow
 
the
 
steps
 
below:
 
1.
 
 
 
Press
 
the
 
Menu
 
button
 
to
 
open
 
the
 
main
 
menu.
 
2.
 
 
 
Press
 
the
 
cursor
 
left/right
 
button
 
to
 
move
 
to
 
the
 
Information
 
menu.
 
3.
 
 
 
Press
 
the
 
cursor
 
up/down
 
button
 
to
 
move
 
to
 
Network
 
Setting
 
in
 
the
 
Information
 
menu.
 
4.
 
 
 
Press
 
the
 
Enter
 
button
 
to
 
access
 
the
 
Network
 
Setting
 
menu.
 
The
 
Netowrk
 
Setting
 
menu
 
is
 
shown
 
below.
 
 
 
Using
 
the
 
DHCP
 
address
 
settings
 
Set
 
the
 
IP
 
Setting
 
to
 
DHCP
 
if
 
you
 
are
 
using
 
a
 
DHCP
 
server
 
that
 
will
 
assign
 
an
 
IP
 
address
 
to
 
the
 
projector.
   
Chapter
 
6.
 
Remote
 
network
 
operation
 
6-5 
						

							1.
   
 
Enter
 
the
 
address
 
of
 
the
 
projector
 
in
 
the
 
address
 
bar
 
of
 
your
 
browser.
 
Example:
 
http://10.0.50.100
 
The
 
Remote
 
page
 
opens.
 
2.
 
 
 
Click
 
IP
 
Settings.
  
 
 
 
3.
 
 
 
Check
 
the
 
DHCP
 
Address
 
radio
 
button
 
and
 
click
 
Set.
Enabling
 
and
 
disabling
 
passwords
 
The
 
default
 
setting
 
is
 
Disable
 
and
 
no
 
password
 
has
 
been
 
set.
   
6-6
 
IBM
 
C400
 
PROJECTOR:
 
User ’s
 
Guide 
						

							1.
   
 
Click
 
Administrate
 
Settings.
 
The
 
Administrate
 
Settings
 
page
 
opens.
  
 
 
 
2.
 
 
 
Check
 
the
 
Enable
 
radio
 
button
 
and
 
then
 
click
 
Set
 
OR
 
Click
 
the
 
Disable
 
radio
 
button
 
and
 
then
 
click
 
Set.
  
 
 
 
3.
 
 
 
Click
 
your
 
browser
 
back
 
button
 
to
 
go
 
to
 
the
 
Input
 
PASSWORD
 
box.
  
 
 
 
4.
 
 
 
Enter
 
the
 
password
 
and
 
click
 
Login.
Setting
 
the
 
maximum
 
connections
 
Refer
 
to
 
the
 
following
 
to
 
limit
 
the
 
amount
 
of
 
users
 
that
 
can
 
log
 
on
 
to
 
the
 
projector.
   
Chapter
 
6.
 
Remote
 
network
 
operation
 
6-7 
						

							1.
   
 
Click
 
Administrate
 
Settings.
 
The
 
Administrate
 
Settings
 
page
 
opens.
  
 
 
 
2.
 
 
 
Enter
 
the
 
amount
 
and
 
click
 
Set.
  
 
 
Retrieving
 
a
 
forgotten
 
password
 
Refer
 
to
 
the
 
following
 
to
 
retrieve
 
a
 
forgotten
 
password.
   
6-8
 
IBM
 
C400
 
PROJECTOR:
 
User ’s
 
Guide