IBM C400 Projector User Manual

							Chapter
 
2.
 
Setting
 
up
 
the
 
projector
 
This
 
chapter
 
provides
 
information
 
on
 
positioning
 
the
 
projector,
 
connecting
 
a
 
computer
 
source
 
and
 
displaying
 
and
 
adjusting
 
an
 
image.
 
Starting
 
the
 
projector
 
To
 
start
 
the
 
projector,
 
do
 
the
 
following:
 
1.
   
 
Connect
 
the
 
power
 
cord
 
to
 
the
 
projector
 
as
 
shown
 
below.
 
Connect
 
the
 
other
 
end
 
of
 
the
 
cord
 
to
 
an
 
electrical
 
outlet.
 
The
 
Power
 
and
 
Lamp-ready
 
LEDs
 
turn
 
on.
  
 
 
 
2.
 
 
 
Remove
 
the
 
lens
 
cover.
 
3.
 
 
 
Attach
 
the
 
input
 
devices.
 
4.
 
 
 
Turn
 
on
 
the
 
connected
 
input
 
devices.
 
5.
 
 
 
Be
 
sure
 
that
 
the
 
Power
 
LED
 
is
 
on
 
(not
 
flashing)
 
amber
 
and
 
then
 
press
 
the
 
Power
 
button
 
to
 
turn
 
on
 
the
 
projector.
 
The
 
projector
 
display
 
window
 
opens
 
and
 
the
 
projector
 
detects
 
connected
 
devices.
 
If
 
you
 
connected
 
the
 
projector
 
to
 
an
 
IBM
 
computer,
 
press
 
Fn+F7
 
on
 
the
 
computer
 
to
 
switch
 
the
 
display
 
output
 
to
 
the
 
projector.
 
If
 
you
 
connected
 
the
 
projector
 
to
 
a
 
non-IBM
 
computer,
 
refer
 
to
 
the
 
documentation
 
that
 
came
 
with
 
your
 
computer
 
for
 
information
 
on
 
how
 
to
 
change
 
the
 
display
 
output.
 
 
Attention:
 
 
Do
 
not
 
look
 
directly
 
into
 
the
 
projection
 
lens
 
when
 
the
 
lamp
 
is
 
turned
 
on.
 
The
 
bright
 
light
 
might
 
harm
 
your
 
eyes.
 
6.
 
 
 
If
 
you
 
have
 
connected
 
more
 
than
 
one
 
input
 
device
 
to
 
the
 
projector,
 
toggle
 
the
 
Source
 
button
 
to
 
change
 
devices.
 
(DVD
 
and
 
HDTV
 
are
 
supported
 
through
 
the
 
DVI-I
 
cable
 
connector.)
 
7.
 
 
 
For
 
information
 
on
 
turning
 
off
 
the
 
projector,
 
go
 
to
 
“Turning
 
off
 
the
 
projector.”
 
Attention:
 
 
Before
 
moving
 
the
 
projector,
 
be
 
sure
 
to
 
power
 
down
 
the
 
projector
 
normally
 
and
 
disconnect
 
the
 
projector
 
from
 
the
 
main
 
power
 
source.
 
See
 
“Turning
 
off
 
the
 
projector”
 
for
 
more
 
information
 
on
 
turning
 
off
 
the
 
projector
 
normally.
 
Turning
 
off
 
the
 
projector
 
To
 
turn
 
off
 
the
 
projector,
 
do
 
the
 
following:
 
1.
 
 
 
Press
 
the
 
Power
 
button.
  
©
 
Copyright
 
IBM
 
Corp.
 
2004
 
2-1  
						

							The
 
projector
 
prepares
 
for
 
shut-down
 
and
 
the
 
Wait
 
a
 
moment
 
message
 
displays,
 
as
 
shown
 
below.
 
The
 
projector
 
turns
 
off
 
automatically
 
within
 
5
 
seconds.
    
 
Note:
 
 
This
 
operation
 
can
 
be
 
cancelled
 
by
 
pressing
 
a
 
button
 
other
 
than
 
the
 
Power
 
button.
 
Pressing
 
the
 
Power
 
button
 
again
 
will
 
turn
 
off
 
power.
 
Note:
 
 
Leave
 
the
 
power
 
cable
 
plugged
 
in
 
for
 
at
 
least
 
2-5
 
minutes
 
until
 
the
 
projector
 
returns
 
to
 
room
 
temperature
 
before
 
placing
 
the
 
projector
 
inside
 
the
 
soft
 
case.
 
Placing
 
the
 
projector
 
into
 
the
 
case
 
too
 
soon
 
after
 
turning
 
off
 
the
 
power
 
could
 
cause
 
the
 
projector
 
to
 
overheat.
 
2.
 
 
 
Press
 
the
 
Power
 
button
 
when
 
the
 
Power
 
Off?/Press
 
Power
 
again
 
message
 
displays,
 
as
 
shown
 
below.
  
 
 
The
 
projector
 
turns
 
off.
Positioning
 
the
 
projector
 
To
 
determine
 
where
 
to
 
position
 
the
 
projector,
 
consider
 
the
 
size
 
and
 
shape
 
of
 
your
 
screen,
 
the
 
location
 
of
 
your
 
power
 
outlets,
 
and
 
the
 
distance
 
between
 
the
 
projector
 
and
 
the
 
rest
 
of
 
your
 
equipment.
 
Following
 
are
 
some
 
general
 
guidelines:
 
v
 
 
 
Position
 
the
 
projector
 
on
 
a
 
flat
 
surface
 
at
 
a
 
right
 
angle
 
to
 
the
 
screen.
 
The
 
projector
 
must
 
be
 
at
 
least
 
1.5
 
m
 
(4.9
 
ft)
 
from
 
the
 
projection
 
screen.
 
v
 
 
 
Position
 
the
 
projector
 
within
 
2.7
 
m
 
(9
 
ft)
 
of
 
your
 
power
 
source
 
and
 
within
 
1.8
 
m
 
(6
 
ft)
 
of
 
your
 
video
 
device
 
(unless
 
you
 
purchase
 
extension
 
cables).
 
To
 
ensure
 
adequate
 
cable
 
access,
 
do
 
not
 
place
 
the
 
projector
 
within
 
.15
 
m
 
(6
 
in.)
 
of
 
a
 
wall
 
or
 
other
 
object.
 
v
 
 
 
Position
 
the
 
projector
 
the
 
desired
 
distance
 
from
 
the
 
screen.
 
The
 
distance
 
from
 
the
 
lens
 
of
 
the
 
projector
 
to
 
the
 
screen,
 
the
 
zoom
 
setting,
 
and
 
the
 
video
 
format
 
determine
 
the
 
size
 
of
 
the
 
projected
 
image.
 
Attention:
 
 
Ensure
 
that
 
projector
 
air
 
flow
 
is
 
sufficient
 
and
 
not
 
blocked
 
or
 
using
 
recirculated
 
air.
 
Please
 
also
 
ensure
 
that
 
the
 
projector
 
is
 
not
 
in
 
a
 
confined
 
space.
  
2-2
 
IBM
 
C400
 
PROJECTOR:
 
User ’s
 
Guide 
						

							Figure
 
2-1.
 
Image
 
height
    
Figure
 
2-2.
 
Image
 
width
 
  
Table
 
2-1.
 
Projection
 
distance
 

1
 
(m/ft)
 
Image
 
Width
 

2
 
(m/in.)
 
Diagonal
 
image
 
size
 

3
 
(m/in.)
 
Image
 
height
 

4
 
(m/in.)
 
1.5
 
m/4.92
 
ft
 
1.1
 
m/42.5
 
in.
 
0.9
 
m/33.8
 
in.
 
0.7
 
m/25.6
 
in.
 
2.0
 
m/6.56
 
ft
 
1.4
 
m/56.7
 
in.
 
1.2
 
m/45.3
 
in.
 
0.9
 
m/34.0
 
in.
 
2.4
 
m/7.87
 
ft
 
1.7
 
m/67.7
 
in.
 
1.4
 
m/53.9
 
in.
 
1.0
 
m/40.5
 
in.
 
2.8
 
m/9.18
 
ft
 
2.0
 
m/79.1
 
in.
 
1.6
 
m/62.9
 
in.
 
1.2
 
m/47.4
 
in.
 
3.2
 
m/10.5
 
ft
 
2.3
 
m/90.5
 
in.
 
1.8
 
m/72.4
 
in.
 
1.4
 
m/54.3
 
in.
 
3.6
 
m/11.81
 
ft
 
2.6
 
m/101.9
 
in.
 
2.1
 
m/81.5
 
in.
 
1.5
 
m/61.0
 
in.
 
4.0
 
m/13.12
 
ft
 
2.9
 
m/113.4
 
in.
 
2.3
 
m/90.6
 
in.
 
1.7
 
m/68.1
 
in.
 
4.4
 
m/14.43
 
ft
 
3.2
 
m/124.8
 
in.
 
2.5
 
m/99.6
 
in.
 
1.9
 
m/74.8
 
in.
 
4.8
 
m/15.74
 
ft
 
3.5
 
m/135.8
 
in.
 
2.8
 
m/108.7
 
in.
 
2.1
 
m/81.6
 
in.
 
5.2
 
m/17.06
 
ft
 
3.7
 
m/147.2
 
in.
 
3.0
 
m/117.7
 
in.
 
2.2
 
m/88.2
 
in.
 
5.6
 
m/18.37
 
ft
 
4.0
 
m/158.7
 
in.
 
3.2
 
m/126.8
 
in.
 
2.4
 
m/95.3
 
in.
 
5.0
 
m/19.68
 
ft
 
4.3
 
m/170.1
 
in.
 
3.5
 
m/135.8
 
in.
 
2.6
 
m/101.9
 
in.
 
10.0
 
m/32.8
 
ft
 
7.2
 
m/283.5
 
in.
 
5.8
 
m/226.8
 
in.
 
4.3
 
m/170.1
 
in.
 
   
Chapter
 
2.
 
Setting
 
up
 
the
 
projector
 
2-3 
						

							Adjusting
 
the
 
projector
 
level
 
and
 
height
 
To
 
adjust
 
the
 
projector
 
level
 
and
 
height,
 
complete
 
the
 
following
 
procedure:
 
1.
   
 
To
 
raise
 
the
 
height
 
of
 
the
 
projector,
 
lift
 
the
 
projector
 

1and
 
press
 
the
 
height-adjuster
 
buttons
 

2.
 
The
 
elevator
 
foot
 

3drops
 
down.
 
2.
 
 
 
To
 
make
 
minor
 
adjustments
 
to
 
the
 
height,
 
rotate
 
the
 
elevator
 
foot
4
 
as
 
shown
 
below.
 
3.
 
 
 
To
 
lower
 
the
 
level
 
of
 
the
 
projector,
 
press
 
the
 
height-adjuster
 
button
 
and
 
press
 
down
 
on
 
the
 
top
 
of
 
the
 
projector.
 
 
 
Note:
 
 
v
 
 
 
The
 
projector
 
table
 
or
 
stand
 
should
 
be
 
level
 
and
 
sturdy.
 
v
 
 
 
Position
 
the
 
projector
 
so
 
that
 
it
 
is
 
perpendicular
 
to
 
the
 
screen.
 
v
 
 
 
Be
 
sure
 
the
 
cables
 
are
 
not
 
in
 
a
 
place
 
where
 
they
 
can
 
knock
 
over
 
the
 
projector.
Adjusting
 
the
 
image
 
To
 
adjust
 
the
 
zoom,
 
focus,
 
and
 
keystone
 
for
 
the
 
image,
 
do
 
the
 
following:
   
2-4
 
IBM
 
C400
 
PROJECTOR:
 
User ’s
 
Guide 
						

							1.
   
 
Twist
 
the
 
rings
 
on
 
the
 
projector
 
to
 
adjust
 
the
 
focus
 

1
 
and
 
zoom
 

2,
 
as
 
shown
 
below.
  
 
 
 
2.
 
 
 
Use
 
the
 
Keystone
 
buttons
 
on
 
the
 
projector
 
or
 
the
 
remote
 
to
 
correct
 
image-trapezoid
 
(wider
 
top
 
or
 
bottom)
 
effect.
 
The
 
Keystone
 
buttons
 
on
 
the
 
remote
 
and
 
projector
 
are
 
shown
 
below.
  
 
 
The
 
keystone
 
control
 
appears
 
on
 
the
 
On
 
Screen
 
Display
 
(OSD),
 
as
 
shown.
  
 
 
Adjusting
 
the
 
volume
 
To
 
adjust
 
the
 
volume,
 
do
 
the
 
following:
 
1.
 
 
 
Press
 
the
 
Volume
 
+/-
 
buttons
 
on
 
the
 
projector
 
or
 
the
 
remote
 
control.
 
The
 
volume
 
control
 
appears
 
on
 
the
 
OSD.
  
 
 
   
Chapter
 
2.
 
Setting
 
up
 
the
 
projector
 
2-5 
						

							2.
   
 
Use
 
the
 
Volume
 
+/-
 
buttons
 
shown
 
below
 
to
 
adjust
 
the
 
level.
  
 
 
 
3.
 
 
 
Press
 
the
 
Mute
 
button
 
(on
 
the
 
remote
 
control
 
only)
 
to
 
turn
 
off
 
the
 
volume.
 
4.
 
 
 
Press
 
any
 
Volume
 
+/-
 
buttons
 
on
 
the
 
projector
 
or
 
remote
 
control
 
to
 
turn
 
off
 
mute.
  
2-6
 
IBM
 
C400
 
PROJECTOR:
 
User ’s
 
Guide 
						

							Chapter
 
3.
 
Connecting
 
devices
 
to
 
the
 
projector
 
This
 
chapter
 
provides
 
information
 
on
 
connecting
 
devices
 
to
 
the
 
C400
 
projector.
 
Connecting
 
devices
 
Computers
 
and
 
video
 
devices
 
can
 
be
 
connected
 
to
 
the
 
projector
 
at
 
the
 
same
 
time.
 
Refer
 
to
 
the
 
documentation
 
that
 
comes
 
with
 
the
 
connecting
 
device
 
to
 
verify
 
that
 
the
 
device
 
has
 
the
 
appropriate
 
output
 
connector.
    
 
 

1
 
Local
 
Area
 
Network
 
RJ-45
 

2
 
RS-232
 
Note:
 
This
 
is
 
a
 
service
 
port
 
and
 
is
 
not
 
intended
 
for
 
personal
 
use.
 

3
 
Monitor
 
out
 

4
 
DVI-I
 

5
 
Composite
 
video
 

6
 
S-video
 
Note:
 
If
 
your
 
video
 
equipment
 
has
 
both
 
S-video
 
and
 
RCA
 
(composite
 
video)
 
jacks,
 
connect
 
to
 
the
 
S-video
 
connector
 
for
 
optimal
 
signal
 
quality.
 

7Audio-in
 

8Audio-out
 

9USB
  
©
 
Copyright
 
IBM
 
Corp.
 
2004
 
3-1  
						

							Connecting
 
to
 
a
 
USB
 
device
 
To
 
control
 
your
 
computer
 
mouse
 
using
 
the
 
projector
 
remote
 
control,
 
connect
 
the
 
projector
 
to
 
the
 
computer
 
with
 
a
 
USB
 
cable
 
as
 
shown
 
below.
    
 
Note:
 
 
USB
 
mouse
 
function
 
is
 
only
 
supported
 
with
 
Windows
 
2000
 
and
 
Windows
 
XP.
 
Connecting
 
to
 
a
 
computer
 
monitor
 
If
 
you
 
are
 
using
 
a
 
desktop
 
computer
 
and
 
want
 
to
 
see
 
the
 
image
 
on
 
your
 
computer
 
screen
 
as
 
well
 
as
 
on
 
the
 
projection
 
screen,
 
plug
 
the
 
monitor
 
cable
 
to
 
the
 
Monitor
 
out
 
connector
 
on
 
the
 
projector.
   
3-2
 
IBM
 
C400
 
PROJECTOR:
 
User ’s
 
Guide 
						

							Chapter
 
4.
 
Using
 
the
 
projector
 
features
 
This
 
chapter
 
provides
 
information
 
on
 
installing
 
the
 
remote
 
control
 
batteries
 
and
 
on
 
using
 
the
 
remote
 
control,
 
audio,
 
keypad
 
buttons,
 
and
 
other
 
projector
 
features.
 
Before
 
you
 
begin
 
Before
 
you
 
can
 
use
 
the
 
remote
 
control,
 
you
 
must
 
install
 
the
 
AAA
 
batteries
 
that
 
come
 
with
 
this
 
projector.
 
To
 
install
 
the
 
batteries,
 
do
 
the
 
following:
 
Note:
   
v
 
 
 
Use
 
only
 
AAA
 
alkaline
 
batteries.
 
v
 
 
 
Dispose
 
of
 
used
 
batteries
 
according
 
to
 
local
 
government
 
ordinance
 
regulations.
 
v
 
 
 
Remove
 
the
 
batteries
 
when
 
not
 
using
 
the
 
remote
 
control
 
for
 
prolonged
 
periods.
1.
   
 
Remove
 
the
 
battery
 
compartment
 
cover
 
from
 
the
 
remote
 
control
 
as
 
shown.
  
 
 
 
2.
 
 
 
Insert
 
the
 
supplied
 
batteries
 
into
 
the
 
remote
 
control
 
battery
 
compartment,
 
aligning
 
the
 
polarity
 
(+/-)
 
of
 
the
 
batteries
 
with
 
the
 
polarity
 
icons
 
in
 
the
 
compartment,
 
as
 
shown.
  
 
 
  
©
 
Copyright
 
IBM
 
Corp.
 
2004
 
4-1  
						

							3.
   
 
Replace
 
the
 
cover,
 
as
 
shown.
  
 
 
Using
 
the
 
remote
 
control
 
The
 
figure
 
below
 
provides
 
an
 
illustration
 
of
 
the
 
remote.
  
 
 
CAUTION:
 
To
 
reduce
 
the
 
risk
 
of
 
injury
 
to
 
the
 
eyes,
 
do
 
not
 
look
 
directly
 
into
 
the
 
remote
 
control
 
laser
 
light
 
and
 
do
 
not
 
point
 
the
 
laser
 
light
 
into
 
anyone’s
 
eyes.
 
The
 
remote
 
control
 
is
 
equipped
 
with
 
a
 
Class
 
II
 
laser
 
that
 
emits
 
radiation.
 

1
 
Laser
  
 

2
 
IR
 
transmitter
 

3
 
Status
 
LED
 

4
 
Auto
 

5
 
Blank
 

6
 
Enter
 

7
 
Up
 
cursor
 

8
 
Right
 
cursor
 

9
 
Cursor
 
pad
 

10
 
Keystone
 
top
 

11
 
Keystone
 
bottom
 

12
 
Mute
 

13
 
Right
 
mouse
 

14
 
Left
 
mouse
 

15
 
Volume
 
down
 

16
 
Volume
 
up
 

17
 
Down
 
cursor
 

18
 
Left
 
cursor
 

19
 
Menu
 

20
 
Freeze
 

21
 
Source
 

22
 
Power
  
4-2
 
IBM
 
C400
 
PROJECTOR:
 
User ’s
 
Guide