IBM C400 Projector User Manual
Have a look at the manual IBM C400 Projector User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 60 IBM manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Operating range This remote control uses infrared transmission to control the projector. It is not necessary to point the remote directly at the projector. The remote control will function within a maximum radius of 10m (32.8 ft) and 30° above or below the projector level. If the projector does not respond to the remote control, please see Appendix B, “Troubleshooting,” on page B-1. Note: The remote will still work when it is pointed at the projected image. Projector and remote control buttons The projector can be operated using the remote control or the buttons on the top of the projector. All operations can be carried out with the remote control. The figure below shows the corresponding buttons on the remote control and on the projector for OSD menu operation. 1 Menu 2 Left button 3 Down button 4 Right button 5 Up button 6 Enter button Chapter 4. Using the projector features 4-3
Chapter
5.
On-Screen
Display
menu
controls
This
projector
has
an
On-Screen
Display
(OSD)
that
lets
you
make
image
adjustments
and
change
various
settings.
Note:
Yo u
must
have
a
display
on
the
screen
in
order
to
access
the
OSD.
Navigating
the
OSD
Yo u
can
use
the
remote
control
or
the
buttons
on
the
top
of
the
projector
to
navigate
and
make
changes
to
the
OSD.
The
following
sections
show
the
menus
in
the
OSD.
Language
To
set
the
OSD
language,
do
the
following:
Note:
The
default
OSD
language
is
English.
1.
Press
the
Menu
button.
The
Language
menu
displays.
2.
Press
the
cursor
left/right
buttons
until
Language
is
highlighted.
3.
Press
the
cursor
up/down
buttons
until
the
language
you
want
is
highlighted.
4.
Press
Enter
to
select
the
language.
5.
Press
the
Menu
button
twice
to
close
the
OSD.
The
image
below
shows
the
Language
menu.
The
default
language
is
English.
Quality
menu
The
Quality
menu
can
be
found
through
the
main
menu.
To
access
the
Quality
menu,
follow
these
steps:
1.
Press
the
Menu
button
to
open
the
main
menu.
2.
Press
the
cursor
left/right
button
to
move
to
the
Quality
menu.
©
Copyright
IBM
Corp.
2004
5-1
3. Press the cursor up/down button to move up and down in the Quality menu. The Quality menu is shown below. The following table shows the options that you will see in the Quality menu and the default. Item Description Default Brightness Press the cursor left/right button to adjust the brightness. Range: 0 to 100 50 Contrast Press the cursor left/right button to adjust the contrast. Range: 0 to 100 50 Sharpness Press the cursor left/right button to adjust the display sharpness. Range: 1 to 5 3 Color Temperature Press the cursor left/right button to adjust the video tint/hue. Range: Cool/Normal/Warm Normal Color Saturation Press the cursor left/right button to adjust the video saturation. Range: 0 to 100 50 Color Tint Press the cursor left/right button to adjust the video tint/hue. Range: 0 to 100 50 5-2 IBM C400 PROJECTOR: User ’s Guide
Item Description Default Gamma Press the cursor left/right button to adjust the gamma correction of the display. Input/Gamma/Brightness: PC/2.2/High, MAC/1.8/High, Video/2.4/Low, Chart/2.2/Low, B&W/2.4/High PC Color Space Press the cursor left/right button to adjust the color space. Range: Auto/RGB/YpbPr/YCbCr Auto Cancel Press the enter button to reset Brightness, Contrast, Sharpness, Color Temperature, Color Saturation, Color Tint, Gamma, and Color Space to default values. Not applicable Properties menu The Properties menu can be found through the main menu. To access the Properties menu, follow these steps: 1. Press the Menu button to open the main menu. 2. Press the cursor left/right button to move to the Properties menu. 3. Press the cursor up/down button to move up and down in the Properties menu. The Properties menu is shown below. The following table shows the options that you will see in the Properties menu and the default. Chapter 5. On-Screen Display menu controls 5-3
Item Description Default Horizontal position Press the cursor left/right button to move the image left or right. Range: 0 to 100 50 Vertical position Press the cursor left/right button to move the image up or down. Range: 0 to 100 50 Keystone Press the cursor left/right button to correct distortion of the projected image. Range: -50 to 50 0 Aspect Ratio Press the cursor left/right button to toggle between the 4:3 standard format and 16:9 high Definition TV (HDTV) format. Range: 4.3/16.9 4:3 Digital Zoom Press the Enter button to increase or reduce image size. Not applicable Cancel Press the enter button to reset Aspect ratio and Digital Zoom to default values. Not applicable Options menu To access the Options menu, follow the steps below: 1. Press the Menu button to open the main menu. 2. Press the cursor left/right button to move to the Options menu. 3. Press the cursor up/down button to move up and down within the Options menu. The Options menu is shown below. 5-4 IBM C400 PROJECTOR: User ’s Guide
The following table shows the options that you will see in the Options menu and the default. Item Description Default Blank Screen Press the cursor left/right button to select a background color for blank screen. Range: Black/Red/Green/Blue/White Blue Auto Source Press the cursor left/right button to enable or disable automatic source detection. Range: On/Off On Auto Power Off Press the cursor left/right button to disable automatic shutdown of lamp after 10 minutes of inactivity. Range: On/Off Off Volume Press the cursor left/button to adjust the audio volume. Range: 0 - 8 4 Menu Position Press the cursor left/right button to position the OSD on screen. Range: Left/Right/Center/Down/Up Center Menu Display Press the cursor left/right button to determine timeout delay of OSD. Range: 10-30 seconds 15 seconds Translucent Menu Press the cursor up/down button to set menu screen translucency. Range: On/Off Off Cancel Resets Auto Power-Off, Volume, Menu Position, Menu Display, and Translucent Menu to default values. Not applicable Setup menu To access the View menu, follow the steps below: 1. Press the Menu button to open the main menu. 2. Press the left/right cursor to move to the Setup menu. 3. Press the cursor up/down button to move up and down in the Setup menu. The Setup menu with a single input and the Setup menu with a dual input are shown below. Chapter 5. On-Screen Display menu controls 5-5
The
following
table
shows
the
options
that
you
will
see
in
the
Setup
menu
and
the
default.
Item
Description
Default
Video
type
Press
the
cursor
right/left
button
to
select
the
Video
standard.
Range:
Auto/NTSC/PAL/SECAM
Auto
Figure
5-1.
Setup
Menu
with
single
input
Figure
5-2.
Setup
Menu
with
dual
input
5-6
IBM
C400
PROJECTOR:
User ’s
Guide
Item Description Default Video automatic gain control (AGC) Press the cursor right/left button to enable or disable AGC for video source. Range: On/Off On Projection Press the cursor left/right button to select from four projection methods. Range: Desktop mount, front of screen/Desktop mount, rear of screen/Ceiling mount, front of screen/Ceiling mount, rear of screen Desktop mount, front of screen Frequency Press the cursor left/right button to adjust the A/D sampling clock. Range: 0-100 Auto detected Tracking Press the cursor left/right button to adjust the A/D sampling number. Range: 0-100 Auto detected Pip Size Press the cursor left/right button to adjust the secondary image size. Note: Pip Size is only available when the projector is connected to dual input sources. Range: Off/Small/Medium/Large Off Pip Position Press the cursor left/right button to adjust the secondary image location. Note: Pip Position is only available when the projector is connected to dual input sources. Range: Upper left to lower right Upper Left Pip Input Press the cursor left/right button to adjust the secondary image source. Note: Pip Input is only available when the projector is connected to dual input sources. Range: Auto/Video/S-video Auto Cancel Resets Video Type, Video AGC, and Projection to default values. N/A Information menu To access the Information menu, follow the steps below: 1. Press the Menu button to open the main menu. Chapter 5. On-Screen Display menu controls 5-7
2. Press the cursor left/right button to move to the Information menu. 3. Press the cursor up/down button to move up and down in the Information menu. The Information menu is shown below. The following table shows the options that you will see in the Information menu. Item Description Video Information Displays the resolution and refresh rate of the connected video device. Software Version Displays information about the firmware version information. Lamp Hours Displays lamp hours used information. Network DHCP Displays Network DHCP status information. Network IP Address Displays IP address information. Network Setting Displays the Network Setting menu. Lamp Mode Toggles between Normal and ECO lamp modes. ECO mode uses less power but decreases the lamp brightness Lamp Hour Reset Reset this item after replacing the lamp. For more information, refer to “Replacing the projector lamp” on page A-1 Cancel Resets Lamp Mode to the default setting. Network Setting menu To access the Network Setting menu, follow the steps below: 1. Press the Menu button to open the main menu. 2. Press the cursor left/right button to move to the Information men. 3. Press the cursor up/down button to move to Network Setting in the Information menu. 4. Press the cursor left/right button or the Enter button to select the Network Setting menu. An example Network Setting menu is shown below. 5-8 IBM C400 PROJECTOR: User ’s Guide