Hyundai H Led19v8 Instruction Manual

							LED TV
Руководство по эксплуатации 
Instruction manual
H-LED19V8
ТЕЛЕВИЗОР
ЦВЕТНОГО ИЗОБРАЖЕНИЯ
ЖИДКОКРИСТАЛЛИЧЕСКИЙ (LCD)
ME61
Downloaded From TV-Manual.com Manual” 
						

							Table of contents 
Before you start 
Utilization of the product 
Important safeguards
InstallationStand installation
Connection
Connection Outdoor antenna connection
Other connections
Operation
Control elements  Front panel
 Back panel
Remote controller Changing the battery
General operations Teletext operations
OSD operation Picture setting
Sound setting
Setting page
 Geometry setting Channel setting
USB operation General information
File playback
General information
Troubleshooting Causes of interference
Accessories
Specifications
2 3
Table of contentsBefore you start
Dear customer!Thank you for purchasing our product. For safety, it is strongly recommended to read 
this manual carefully before connecting, operating and/or adjusting the product and keep 
the manual for reference in the future.
2
3
3
3
4
4
5
5
5
5
6
6
6
6
7
7
8
8
8
9
9
9
10
10
10
10
11
12
12
12
13
13
Downloaded From TV-Manual.com Manual” 
						

							23
Table of contentsBefore you start
If you want to dispose this product, do not mix it with general household waste. There is 
a separate collection system for used electronic products in accordance with legislation 
that requires proper treatment, recovery and recycling. Please contact your local authorities for the correct method of disposal. By doing so, 
you will ensure that your disposed product undergoes the necessar y treatment, recovery 
and recycling and thus prevent potential negative effects on the environment and human 
health.
Utilization of the product
Important safeguards
•  Before connecting the AC power cord 
to the DC adapter outlet, make sure that 
the voltage designation of the DC adapter 
corresponds to the local electrical supply. •  Accessories include a DC adaptor SAWA-
12-50012. Do not use other adaptors with this 
unit. •  Please unplug the power cord from the AC 
outlet and contact a service center for repair 
if following occurs: any obvious abnormality 
appears in the unit, such as smoky, peculiar 
smell or strange sound; liquid has been spilled or 
other objects have fallen into the unit; no picture 
or sound; cover or panel is broken; although you 
have operated the unit following the operating 
instructions, it still cannot work normally. •  This unit should only be connected to a 
wall socket having grounding. •  Always disconnect the power cord and 
antenna during a storm. •  Do not fix the power cord with a metal nail.
•  Unplug the power cord from the AC outlet; 
also unplug the signal cables from the input 
ports when the unit is unused for long periods 
of time. •  When unplugging the plug, always hold 
the wide slot, do not touch the metal part, and 
do not destroy, refit, twist, pull or roast the 
power cord. •  Please contact the service center 
immediately if you found that the core is  showed in the air or has been broken.
•  Please replace the AC outlet if the metal 
bolt cannot be inserted into the power socket 
completely or it cannot be fastened even when 
it was pushed in, otherwise, any accidents of 
shocks and fires would happen. •  Never touch the antenna lie or power plug 
if it stars to thunder. •  Do not touch the power plug with wet 
hands. •  Do not use any non-rated power socket 
with numerous devices jointed on one power 
socket or cable device. The wire of non-
designated capacity may cause the fire due to 
the generation of heat. •  All instructions must be read and 
understood well before you operate the unit. 
Heed all warnings and follow all instructions. •  Please use the accessories provided 
by the manufacturer. Using inadequate 
accessories may result in accidents. •  Please adjust the product through the 
panel buttons or the remote controller, do 
not remove the cover or attempt to service 
the product by yourself. Do not disassemble 
back cover and do not make maintenance by 
yourself to avoid the electric shock. •  Over-press the panel may destroy the 
product. •  Do not place the product on an unstable 
cart, stand surface, tripod, bracket, or table. 
The product may fall, causing serious accidents 
as well as the damage to the product. 
Downloaded From TV-Manual.com Manual” 
						

							4
Before you start
•  Please place the product on a flat surface 
in a well-ventilated location. Keep it away from 
the burning-light, direct sunlight, vibration, 
high-temperature and humidity. •  Do not place any vase, potted plant, cup, 
medicine and any container with water on this 
product. If the liquid is spilt, it may cause the 
fire, electric shock or breakdown. •  Do not install it at the place on the strong 
magnetic field or current field. It may cause 
break down. This equipment may be observed 
deterioration of the picture by electromagnetic 
radiation in electromagnetic environment. •  Fasten the wheel of the product or shelf 
with wheels when installing this product. If it 
moves or is tipped over, it may be damaged. •  Do not place any fire source such as 
candlelight close to this product or place it on 
this product. If it is tipped over or fallen down, it 
may cause damage or fire. •  Do not place the unit into closed space 
of TV for better ventilation; it can reduce the 
product lifetime. Keep a space at least 10 cm 
at above, left and right of the TV. •  Please place all the signal cords behind of 
rear panel. •  Do not overexert or touch the panel when 
you convey the product. Do not transfer the 
LED TV up or down display direction. •  Do not transport it with the power cord 
or the connection cable connected. If you 
move this product with the power cord or the 
connection cable connected, the damaged 
power cord, connection cable or connection 
terminal may cause the fire, the electric shock 
or breakdown. •  2 persons or more shall transport the 
device, which is heavier than 18 kg. If you drop 
or tip over the device, it may damage it. •  The temperature of the product’s body 
becomes a little higher after a long period use. 
This phenomenon indicates that heat exchange 
in normal working mode, thus please do not 
let children or anyone who is sensitive of 
temperature to touch.
All images provided herein are schematic 
drawings and may differ from of real objects.Installation
Stand installation
Align the holes in the glass stand, base, ring 
and bracket and fix these 4 parts by 3 supplied 
screws as shown below:
Place the LED TV on a solid flat surface. 
Use soft material to place over the front screen 
to avoid any damage. Insert the bracket of the 
stand assembly into the slit in the bottom part 
of the TV cabinet, then fix the stand assembly 
with 2 supplied screws as shown below.  
Downloaded From TV-Manual.com Manual” 
						

							5
Connection
Connection
Outdoor Antenna Connection
Use 75Ω coaxial cable plug or 300-75Ω 
impedance converter to plug in antenna input 
terminal on the rear of the cabinet.
Other connections•  Connect a video source to the Composite 
video input jack with RCA cable (not included). •  Connect an audio source to the proper 
Audio input jacks (left and right). •  Connect the included DC adapter to the 
DC input of this unit. •  When using the unit as a computer screen, 
connect the PC to the VGA jack of the unit by 
the relevant cable to get the video signal from 
the PC. For audio signal from the PC, connect 
the left and right jacks of the VGA/Component 
audio input of this unit to the audio output jack 
of the PC by using relevant connector (not  included).
•  If the video source has a HDMI output 
jack, you can connect the signal to the unit by 
HDMI cable (not included). •  Component input is intended for receiving 
component video signal if connected to the 
component output of external signal source. •  Connect an external device (e.g., VCR-/
DVD-recorder) to the proper Audio/Video 
output jacks of this unit with AV RCA cable (not 
included). •  Coaxial output is intended for transmitting 
multi-channel sound to an external decoder 
(e.g. in 5.1-CH format). RCA cable should be 
used for connection.
75 Ohm co-axis cable
TVRF antenna jack
Antenna cable connector
Downloaded From TV-Manual.com Manual” 
						

							6
Operation
Control elements    
Front panel
1
2
  1. IR sensor
  2. Power indicator
1. POWER button
2. CH+/- buttons
3. VOL+/- buttons
4. MENU button
5. SOURCE button
6. USB port
7. Audio stereo input-2
8. Composite video input-2
9. DC adaptor input
10. HDMI input
11. Component video input
12. Audio input for VGA and component video
13. Coaxial output (SPDIF)
14. Video/audio input-1
15. Composite video/audio output 
16. VGA input
17. RF antenna jack
Back panel
1 2 345
6
7
8
9
10
11
12
1314 15 1617
Downloaded From TV-Manual.com Manual” 
						

							7
Operation
Remote controller (RC)
1
2
3
4
5
6
7
8
9
10
11
12 13
14
15
16
17
18
19
20
21
22
Index
Size
Rev.Hold. Sub
1.  button
2. Number buttons
3. INFO button
4. SOURCE button
5. Cursor (UP/DOWN/LEFT/RIGHT) buttons/
OK button
6. TXT button
7. VOL+/VOL- buttons
8. USB button
9. SCALE/SIZE button 10. PICTURE/REV button 
11. MTS button/red button
12. Green button
13. POWER button
14. RETURN button
15. MENU button
16. EXIT button
17. INDEX button
18. CH+/CH- buttons
19. FREEZE/SUB button
20. SOUND/HOLD button
21. DEMO button
22. Cyan button/
 button
Changing the battery1. Remove the battery compartment cover 
on the back of the RC. 2. Insert the batteries into the battery 
compartment making sure that the correct 
polarity is observed. 3. Install the cover back.
•  Use two AAA batteries for the RC. The RC 
should be pointed at remote sensor within 8 
meters and within 30 degrees at the left or the 
right side.
•  Take the battery out of the RC if it is not 
used for a long time. •  Do not mix new and used batteries or 
different types of batteries. Weak batteries can 
leak and severely damage the RC. •  Do not expose the RC to shock, liquids, 
and do not place it in an area with high 
humidity.
1 23
 
						

							89
OperationOperation
General operations
•  Press POWER button on the unit or on the 
RC to switch on the unit from standby mode. 
When the unit is on, press POWER button on 
the RC to switch the unit to standby. •  Press VOL- button on the unit or on 
the RC repeatedly to decrease the volume; 
press VOL+ button on the unit or on the RC 
repeatedly to increase the volume. •  Press RETURN button on the RC to select 
from the present channel and the previously 
displayed channel. •  Press 
 button to cut off sound, press 
this button again or adjust volume to resume 
sound. •  In TV mode press CH+/CH- buttons on 
the RC or on the unit to select previous or next 
channel; or press number buttons to enter a 
channel number directly. •  Press PICTURE button repeatedly to cycle 
through the available video picture modes from 
the following types: Standard => Bright => Soft 
=> Personal. •  Press SOUND button repeatedly to cycle 
through the available sound modes from the 
following types: Stereo => Movie => Music => 
News => Personal. •  Press INFO button to display the preset 
TV channel information. •  In TV mode press MTS button to switch 
NICAM sound mode (not available for some 
channels). •  Press SCALE button repeatedly to select 
a screen display size from the available list: 
4:3/Full/Subtitle/Wide/Zoom/Expand/Original/
Nature. Available aspects may differ for 
different signal sources. •  Press FREEZE button to freeze the picture 
on or off.
Press SOURCE button, then press cursor 
buttons on the RC to select a source from 
available source list: TV => YPbPr => PC => 
HDMI => AV1 => AV2. Press OK button to 
confirm. You can press USB button to access 
Media source mode directly; you can press TV 
button to access TV source mode directly. •  Press 
 button to enable/disable Natural 
light function. This is to adjust the brightness 
of the backlight according to the content of the 
inputted signal automatically, so as to optimize 
the picture quality and decrease the power 
consumption. •  Press DEMO button to display the menu 
including E care (Eyes care), E saving (Energy 
saving) and E pic (Enhance picture) items. 
Press cursor buttons to select an item and 
press Ok button to demonstrate the selected 
mode of Natural light function. Press DEMO 
button or EXIT button to cancel. 
  It is recommended to demonstrate this 
function in full-screen mode.
TELETEXT operations (option)•  Select the TV source mode. Then press 
CH-/CH+ buttons to select TV channel in order 
to pick up the picture signal of Teletext. •  Teletext button functions are as follows:
TXT: Press this button to enter into Teletext 
mode. Press this button to mix the teletext 
and current TV signal image. Press this 
button again to return to the channel you are 
watching. HOLD: Press this button to stop the move 
to the next page. Press this button again to 
cancel operation. INDEX: Press this button to go to the index 
page.
SIZE: Press this button to enlarge the top 
part of the page. Press this button again to 
enlarge the bottom part of the page. Press this 
button third time to normal size text page view. REV. (Reveal): Press this button to reveal 
the cancelled information. Press this button 
again to cancel the information. SUB. (Subpage): Press this button to select 
sub-page. Input the number of sub-page and 
use numeric buttons in the format 0001 for 
sub page 1. The teletext will search for the sub 
page. Press SUBPAGE button again to exit the 
subpage mode. Red/Green/Yellow/Cyan buttons: Press 
these 4 color buttons to access directly to 
corresponding color page displayed at the 
Downloaded From TV-Manual.com Manual” 
						

							89
OperationOperation
lower parts of teletext screen.
OSD operation
1. Press MENU button to enter the setting 
menu displayed on the screen. 2. Press UP/DOWN cursor buttons on the 
RC to select setting page. 3. Press OK button on the RC to go to the 
parameter list. 4. Press UP/DOWN cursor buttons on the 
RC to select a parameter to adjust. 5. Press LEFT/RIGHT cursor buttons on the 
RC to adjust the selected parameter. 6. Press MENU button to return to the 
previous menu page. Press EXIT button on the 
RC to quit the menu.
  Some menu items may be in grey color, 
in this case they are not adjustable. Pictures 
of OSD menu are for reference only; they may 
differ from the real screens.
Picture setting page
Picture
Backlight
Picture mode
Scale
Brightness
Contrast
Saturation
Sharpness
Tint
Color temperature
Natural light
Dynamic contrast
•  Backlight: adjust the brightness of screen 
backlight depending on environmental lighting. •  Picture Mode: Standard/Bright/Soft/
Personal. •  Scale: 4:3/Full/Subtitle/Wide/Zoom/Ex-
pand/Original/Nature. •  Brightness, Contrast, Saturation, 
Sharpness, Tint (tint available only for NTSC 
system). •  Color temperature: Select color 
temperature mode of the picture - Normal/
Warm/Cool. •  Natural light: to adjust the brightness of 
the backlight according to the content of the 
inputted signal automatically. •  Dynamic contrast: to adjust the image 
contrast automatically.
Sound setting page
Sound
Sound mode
Balance
Sound EQ
•  Sound mode: News/Music/Movie/Stereo/
Personal.
•  Balance: adjust balance between left and 
right speaker. •  Sound EQ: adjust the equalizer. Note: 
after you adjust the equalizer, the sound mode 
will automatically switch to Personal.
Setting page
Setting
DNR
Smart switch
Startup setting
Language
TTX language
Color system
Watch time limit
Time setting
Restore to default
•  DNR: Digital noise reduction effect for 
reducing the video noise level: Off/On, if the 
broadcast signal received is weak. •  Smart switch:
Switch: when the connected external device 
is turned on, the TV will automatically switch to 
the corresponding source mode. Display: when the connected external 
device is turned on, the TV will show a 
prompt message; select OK to switch to the 
corresponding source mode. Off: disable Smart switch function.
•  Startup setting: you can select the default 
startup picture, captore picture (Logo) and no 
startup picture (Off). 
Downloaded From TV-Manual.com Manual” 
						

							10
Operation
•  Language: select the language of the 
OSD menu. •  TXT Language: select the language of the 
teletext subtitles. If selected teletext language 
does not correspond to the program language, 
subtitles can be diplayed incorrectly.  •  Color system: PAL/SECAM/NTSC.
•  Watch time limit: set the period of time for 
you to watch the TV; when the time elapses, 
the TV will switch off automatically. You must 
enter the password first (the default password 
is 0000; you can also assign your own 
password in PW Modify menu). If you forgot 
your password, you can use 0432 code. •  Time setting:
Current time: set the current time.
Turnon repeat: Select the mode of TV turn-
on at a specific time (Off/Once/Everyday). 
Note: If Off is selected, Turnon time, Wake 
source and Wake channel are unavailable. Turnon time: set the time at which the TV will 
turn on automatically. Wake source: select the source mode to 
which the TV will automatically turn on. Wake channel: select the channel to which 
the TV will automatically turn on (available only 
if TV is selected as Wake source). Turnoff repeat: Select the mode of TV turn-off 
at a specific time (Off/Once/Everyday). Note: If 
Off is selected, Turnoff time is unavailable. Turnoff time: set the time at which the TV will 
turn off automatically. Sleep time: set the period after which the TV 
will audomatically turn off (0 - 120 minutes). •  Restore to default: reset the parameters 
to initial factory settings. 
Geometry setting (only for PC mode)
Geometry
Auto adjust
H position
V position
AD clock
Phase
•  Auto adjust: automatical setting of the 
parameters.
•  Horizontal Position: adjust horizontal 
position of the image. •  Vertical Position: adjust vertical position 
of the image. •  AD clock: adjust the image frequency 
manually. •  Phase: adjust the phase manually.
Channel setting
Channel
Auto tuning
Intellegent tuning
Manual tuning
Fine-tune
Sound system
Channel edit
•  Auto tuning: press OK button to start 
automatic search of available channels. To 
stop the process press MENU or EXIT button. •  Intellegent tuning: This operation will 
keep all the existed channels and add newly 
found channels to the end of the channel list. 
To stop search, press MENU button; detected 
channels will be stored. •  Manual tuning: Press OK button to enter 
into manual tuning menu: Channel: select channel number.
Band: select frequency band (VHFH/UHF/
VHFL). Frequency: adjust the current frequency step 
by step. •  Fine tune: adjust the current frequency 
manually to improve the quality of signal if it is 
too week. •  Sound system: select the sound system 
(DK/BG/I/M). •  Channel edit:
Current Channel: select the current channel 
number. Target Channel: select a target channel for 
swapping. Skip: select Current channel number to be 
skipped. Select Skip item and select Yes to 
confirm. Now this channel will be skipped when 
next/previous channels are selected. Swap: select Current channel and Target 
Downloaded From TV-Manual.com Manual”