Home > Husqvarna > Sewing Machine > Husqvarna Designer 1 Instruction Manual

Husqvarna Designer 1 Instruction Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Husqvarna Designer 1 Instruction Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 35 Husqvarna manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							71
    Embroidery
    Slide the hoop onto the embroidery arm until it 
    clicks into place. Press the purple button on the 
    embroidery clip to release the hoop and slide it 
    toward you. 
    Use the move design buttons to move the de-
    sign to a different place in the hoop area. This 
    is especially helpful when the fabric is hooped 
    and the marked center starting position is not 
    in the center of the hoop. Touch the arrows to 
    move the hoop until the needle lines up with 
    the mar ked starting point. An audible beep will 
    advise you of the limits. If you want to get back 
    to the center, touch 
    .
    Starting position
    The numbers indicates starting position of the de-
      sign, in mm, from origin. When changed plus (+) 
    indicates right and up, minus (-) down and left.
    Tip: If you need to turn off your Designer I whi-
    le stitching large embroidery, make notes of star-
    ting position, stitch number and color number. 
    Then you can continue from where you left off.
    Use the check size button 
       to check the size 
    and the outline area of the de sign on your fa-
    bric. When the check size button has been acti-
    vated, it becomes dark brown with a white ar-
    row indicating the current position  
     . 
    When you select an embroidery the hoop is po-
    sitioned so the needle will begin at the center 
    of the hoop. However, if you select a design to 
    make a sequence of embroidy, the needle will 
    begin where the last embroidery was fi nished.
    Touch 
       to go back .
    SET in Embroidery
    If neccessary, for example when embroidering 
    on unusual fabrics, set the thread tension in the 
       menu.
    When embroidering on very thick fabrics or bat-
      ting, you can raise the height of the presser foot. 
    This is to allow the foot to glide over thicker fa-
    bric.
    Manual adjustments of the thread tension and 
    of the presser foot height are made in the 
       menu. 
    						
    							72Embroidery
    Adjust in Embroidery
    There are many options to adjust your design. 
    Always adjust fi rst, before using any of the but-
    tons on the embroidery screen menus (step 
    through stitches, check parameters of de sign, 
    move design in hoop, etc.) and before begin-
    ning to sew.
    To activate Adjust menu touch 
      .
    Rotate embroidery
    Touch 
       to rotate the embroidery in 90 degree 
    steps. See it on the color touch screen. When an 
    embroidery has been rotated, the button will be 
    indicated in brown 
      .
    Mirror image side to side
    Touch 
     
     and the leaf will fl ip side to side. The 
    mirror image button will be indicated in brown.
    Touch 
       to return to normal image
    Size
    Scale embroidery size up or down (up to 20%). 
    An audible beep will advise you of the limits.
    Height  
       
    Use 
        
    .
    Width  
     
    Use 
        
    .
    You can increase the width and height indepen-
    dently to create long and thin or short and wide 
    designs. When enlarging or reducing the size 
    of the embroidery, experiment with dif fe rent 
    weights of embroidery thread.
    Exit 
       by touching  
     or by accessing the   
     or   menu.  
    						
    							73
    Embroidery
    View embroidery colors
    The view color icon appears on the HELP menu 
      . It is grey when not active. When it is colo-
    red and active, touch the icon to view the colors 
    in an embroidery. You can scroll through the 
    colors using 
        
    . 
    The menu shows color number, stitch count and 
    color name. The currrent color is highlighted 
    with a red frame. If the embroidery disk has co-
    lor chart numbers included those will be shown 
    instead of color names. 
    The color menu will stay open when the 
    Designer I is sewing. Close the color menu by 
    touching 
      .
    Embroidery features
    FIX
    Touch FIX in embroidery to baste an outline aro-
      und the embroidery area. This is helpful when 
    embroidering on fabrics that should not be hoo-
    ped tightly. The FIX function can also be used 
    to baste fabric to the stabilizer. This bas ting also 
    indicates placement of embroidery.
    When the FIX function is active, you cannot 
    step forward or backward color by color, ins-
    tead FIX is shown in the thread color recom-
    mendation fi eld.
    If the top thread has run out or broken, you can 
    step backward a few stitches by touching 
      . 
    Touch 
       to step forwards stitch by stitch in the 
    basting stitch. 
    Cursor
    When embroidering, a cursor 
       indicates the 
    needle position in the embroidery. The cur-
    sor follows the needle through the embroidery 
    when sewing or when stepping through stitches 
    or colors.
    One Color Embroidery
    Touch 
       ( the light goes out) to cancel the co-
    lor stops if you want to sew a design in one co-
    lor only. 
    						
    							74Embroidery
    Pop-up menus in Embroidery
    Embroidery Start Up Calibration 
    As the embroidery unit is connected to the mach-
    ine, a Pop-up menu prompts you to slide off the 
    hoop, and clear the machine area for positioning 
    of the embroidery arm. Touch OK to calibrate 
    the embroidery unit and to position the arm. 
    This menu also reminds you to use the R foot.
    Top Thread  Break
    Your Designer I stops automatically if the top th-
    read runs out or breaks. Rethread the top thread, 
    touch OK. Touch 
       to continue.
    Empty Bobbin
    Your Designer I stops when the bobbin is almost 
    empty. Replace the empty bobbin with a full 
    one, touch OK (bobbin winding, see page 10).
    Note: When changing the bobbin, touch  
     and the 
    hoop will move away for easy access to the bobbin 
    case. Once the bobbin is replaced, touch 
       again to 
    move the hoop back to where em broi dery stopped. 
    Touch 
       to resume the embroidery.
    Color Change 
    Your Designer I stops automatically and the top 
    thread only is cut at the color change. Remove 
    the spool and rethread the top with the recom-
    mended color shown in the color menu of the 
    color touch screen or in the Embroidery Booklet. 
    Touch OK and 
       to resume embroidering.
    Cut  Embroidery Top Thread Tail
    Your Designer I stops automatically a few stit-
    ches after you begin embroidering. Cut the 
    star ting thread tail, touch OK and 
     
     to resume 
    embroidering. 
    Wrong hoop for embroidery
    When the size of the hoop on the machine does 
    not match the size displayed on the screen, your 
    Designer I will not sew. Change the hoop to the 
    size displayed on the screen.
    Stop requested in design
    Designer I stops when you are supposed to do a 
    cut work, applique etc. See explanation for each 
    design in the Embroidery Booklet.  
    Embroidery fi nished
    When your embroidery is complete a pop-up 
    menu will appear. Touch OK to get back to your 
    embroidery. 
    						
    							75
    Embroidery
    Start embroidering
    1. Touch  
     to begin embroidering. The 
    presser foot is lowered automatically.
    2. After a few stitches a Pop-up menu will 
    prompt you to cut the starting thread tail. Cut 
    the thread tail. Touch 
       to resume embroi-
    dering.
    3. Your Designer I will stop embroidering and a 
    Pop-up menu will prompt you when the top 
    thread color should be changed.
    4. When your embroidery is complete, your De-
    signer I will stop sewing, the top and bob bin 
    thread are cut automatically, and the presser 
    foot is raised to the extra lift position to make 
    it easy to slide off the hoop.
    To move the hoop forward for 
    easy cutting
    When changing from one thread to another, it is 
    best to cut the long ”jump” stitches that are 
    created when the hoop is moving. This will 
    make the thread cutting easier when the 
    embroidery is fi nished.
    1. Press 
     
    . The hoop moves towards you.
    2. Cut the threads.
    3. Press 
     
     again and the hoop moves back to 
    its ready po si tion.
    4. Press 
     
     to resume the embroidery. 
    						
    							76Embroidery
    Customizing Designs
    Designer I has Built-In customizing. You are 
    able to combine a number of designs and/or 
    lettering programs on the Color Touch Screen to 
    create customized embroidery.
    Customize “Teatime and fl owers”. Slide on the 
    embroidery unit, see page 64. Turn on Designer 
    I, and Main menu appears.
    How to program ”Teatime”
    Slide in the Palace Script Disk.
    Touch 
      .
    Touch 
      . 
    Touch 
      .
    There are three sizes to choose between. Select 
    size 
      .
    Touch 
      . The capital letter T appears on the 
    top of the Color Touch Screen in the program-
    ming area. The cursor line moves to the right 
    ready for the next letter to be entered.
    Note: If you have to correct spelling, use  
    . This 
    button erases your programmed letters backwards 
    step by step.  
    						
    							77
    Embroidery
    Touch   . Now you have opened the lower-
    case menu. You are able to jump between upper 
    case, lower case and numbers by touching
        
      
    .
    Touch  
      ,  
    ,  
    ,  
    ,  
    ,  
    .
    Touch 
       and the letters have been pro-
      gram med.
    The combination you created is now visible on 
    the Color Touch Screen.
    Slide out the Palace Script disk.
    Now you should rotate “Teatime” to fi t in with 
    the following “fl ower designs”.
    Touch 
      .
    Touch 
       once. 
    						
    							78Embroidery
    Select your design. Touch    .  
    The fl ower design is now visible on the screen. 
    A box around the design indicates it is selected 
    and can be worked with.
    If you want to use 20x20mm grid, go to SET sub 
    menu 3 and touch Grid ON.
    Note: Touch  
     to select a part of the customized 
    design. When a part is selected, it is indicated by a 
    box around it. The selected part can be moved or 
    adjusted, but you can also delete it by touching 
      .
    If you want to bring up a design, or a customi-
    zed design from a disk memory, see page 81.
    Combine the word with designs
    Slide in the Designer Sampler Disk 100.
    Touch 
      .
    There are four menus to choose between. Touch 
      . 
    						
    							79
    Embroidery
    Use    to move the design to your selec-
    ted position on the Color Touch Screen.
    Touch 
       to select your second design.
    Touch 
      . A new fl ower design is now visible 
    on the screen. The box around the design indi-
    cates it is selected and can be worked with. 
    Touch   .
    Touch 
      .
    Touch 
       three times.
    Touch 
      . 
    						
    							80Embroidery
    Use    to move the design to your selec-
    ted position on the Color Touch Screen.
    Save your customized design
    Touch 
      . A Pop-up menu appears. Changes 
    not saved! Save now? Enter No or Yes.
    If you select No you are still able to sew your 
    design.     
    If you wish to save your design for future sewing, 
    slide in a PC-formatted disk and select Yes.
    Touch   .
    Touch 
      .
    Touch 
       once.
    Touch 
      . 
    						
    All Husqvarna manuals Comments (7)

    Related Manuals for Husqvarna Designer 1 Instruction Manual