HP Xp8010 Digital Projector Reference Guide

Reference Guide31
Installation and Setup
RGB-equipment connection
■RGB-video BNC cable
■Stereo-audio RCA cable
RGBS-equipment connection
■RGBS-video BNC cable
■Stereo-audio RCA cable 

32Reference Guide
Installation and Setup
RGBHV-equipment connection
■RGBHV-video BNC cable
■Stereo-audio RCA cable
To connect output devices
■VGA cable
■Stereo-audio RCA cable
The speakers must be amplified. 

Reference Guide33
Installation and Setup
To connect control equipment
■9-pin serial cable
■2.5-mm (3/32-in) to 3.5-mm (1/8-in) stereo mini-phone cable
■3.5 × 1.3-mm DC power cable
In some installations, the projector might not be visible to the remote control, such as 
for rear projection. Use one of these solutions to enable the remote control to work:
■Use a remote control extension. Plug its cable into the remote connector on the 
projector. Install the receiver in the room with the presenter.
■Wire...

34Reference Guide
Installation and Setup
Configuring the Projector
To change settings using the on-screen menu
You can change the on-screen menu settings with either the buttons on the projector or 
the remote control buttons.
1. Press enter on the projector or the remote control to open the on-screen menu.
2. Press   up or  down to highlight the desired menu, and press enter to select 
the highlighted option. 
3. Press   up or   down to highlight the desired parameter, and press enter to 
select the...

Reference Guide35
Installation and Setup
To set up network access
1. Plug a CAT5 network cable into the RJ-45 network port on the back of the 
projector.
If the projector has power, the left indicator light on the network port turns on 
showing a 10- or 100-Mb/s connection. The light on the right shows network 
activity.
The projector normally attempts to get an IP address from a Dynamic Host 
Configuration Protocol (DCHP) server, or, if a server is not available, it takes a 
default address. The IP...

36Reference Guide
Installation and Setup
Securing the Projector
The projector includes a built-in slot to secure the projector with a cable and a lock 
(such as the Kensington MicroSaver lock system, available at many computer stores).
1. Wrap the cable around a secure object, such as a table leg. Loop the cable to create 
a slip knot around the stationary object, and be sure it cannot slip off.
2. Insert the lock 
1 into the hole and twist the key 2.
If the cable shroud is installed on the projector,...

Reference Guide37
2
Adjustments
This chapter describes how to make adjustments to the projector. The chapter covers:
■“Making Basic Adjustments” on page 37.
■“Adjusting the Picture” on page 40.
Making Basic Adjustments
This section provides the following instructions:
■“To aim the projector” on page 38
■“To adjust the focus and zoom” on page 39
■“To adjust the audio” on page 39 

38Reference Guide
Adjustments
To aim the projector
■To raise the projected picture on the screen, raise and hold the height adjustment 
lever while lifting the front of the projector to the desired display angle, then 
release the lever to lock the foot.
■To lower the projected picture, raise and hold the height adjustment lever while 
pressing down on the front of the projector, then release the lever to lock the foot.
■To level the projected picture, turn the two back feet to screw in or out. All four...

Reference Guide39
Adjustments
To adjust the focus and zoom
1. Rotate the focus ring 1 until the image becomes clear. The projector can focus at 
distances of 1.5 to 14 m (5 to 46 ft). 
2. Rotate the zoom ring 
2 to adjust the picture size from 100 to 120%.
See “Selecting a Location” on page 17 for more information.
To adjust the audio
1. Open the on-screen menu and select audio.
2. Set the audio adjustments.
From the audio menu, you can select audio inputs, turn off internal speakers, and 
adjust mute,...

40Reference Guide
Adjustments
Adjusting the Picture
This section provides the following instructions:
■“To adjust the image according to type of picture” on page 40
■“To adjust other image settings” on page 40
■“To make adjustments from the web” on page 41
To adjust the image according to type of picture
Use the picture mode buttons on the projector or the remote control to optimize the 
image.
■To optimize the picture for data presentations, press the business graphics  
 button.
■To optimize the...