HP Rt3000 G2 Manual

 
Installation  21  
  
   
  WARNING:
  To meet the requirements stated in NEC (NFPA 70) Articles 645- 10 and 645-11, 
a UPS installed in a computer equipment room must  be connected to a REPO circuit.  
  
   
  IM PORT ANT :
  The remote switch must be in the Off (open) position to enable power to the 
output receptacles.  
  
   
  NOTE:
  Wire the connector block using stranded, nonshielded wire (AWG #22 -  #18, or 
equivalent).  
  
Separate wire pairs are attached to a single, normally -open...

 
Installation  22  
• Use tie wraps and tie wrap blocks to secure the wires tightly to the rack and t he rear of the UPS. 
 
For more information about the REPO port, see " REPO port (on page  10)". 
For information about verifying the REPO connection, see " Verifying the REPO port connection (on page 
44)".  
Connecting the ground bonding cable  l  
  NOTE:
  UPS appearance might vary depending on the specific unit installed.  
  
The ground bonding screw is provided as an attachment...

 
Installation  23  
The ground bonding cable is not included.  
 
 
 
C onnecting the UPS to utility power    
  WARNING:
  To prevent injury from electric shock or damage to the equipment:  
•   Plug the input line cord into a grounded (earthed) electrical outlet that is installed near the 
equipment and is easily accessible.  
•   Do not disable the grounding plug on the input line cord . The grounding plug is an important 
safety feature.  
•   Do not use extension cords.  
  
Connect the UPS to a...

 
Installation  24  
  CAUTION:
  Do not plug laser printers into the UPS output receptacles. The instantaneous 
current drawn by this type of printer can overload the UPS.  
  
Before connecting devices, verify that the UPS will not overload by checking that the ratings of the devices 
do not exceed the UPS capacity. If the equipment rating is listed in amps, multiply the number of amps by 
the selected output voltage to determine the VA.  
After verifying that the UPS will not overload (depending on...

 
Installation  25  
Starting power to the load  
Start power to the load by placing the UPS in Operate mode  (on page 40).   
  IM PORT ANT :
  AC power must be available the first time the UPS is started.  
  
 
I nstalling the ERM in a rack  
Before installing the unit, review and adhere to all warnings provided in " Precautions (on page  12)."   
  W
ARNING:   A risk of personal injury or damage to the equipment exists. Uneven loading of 
equipment in the rack might cause the rack to become...

 
Installation  26  
4.
 
Attach the chassis to the rack using the supplied  screws. 
 
 
Connecting the battery leads  
   

 
Installation  27  
Attaching the ERM front bezel  
 
 
  

 
Instal lation 28  
Connecting the ERM to the UPS  
1. Remove the screws, and then remove the ERM connector bracket from the  UPS. 
 
2.  Connect the ERM cable (2) in the socket (1) at the rear of the UPS.  
  

 
Installation  29  
3.
 
Attach the ERM connector bracket to the UPS as a cord retention bracket for the ERM cable.  
 
4.  To install a second ERM:  
a. Remove the ERM connector bracket from the first ERM.  
b. Connect  the cable from the second ERM into the socket at the rear of the first ERM. Up to two 
ERM units can be connected.   
c. Attach the ERM connector bracket to the first ERM as a cord retention bracket for the ERM cable.   
Switching on the ERM circuit breaker  
  
Charging the ERM...

 
Installation  30  
Installing the optional UPS Network Module   
  NOTE:
  It is not necessary to power down the UPS before installing the UPS Network Module. 
  
You can purchase the optional UPS Network Module by ordering part number AF465A.  
1. Remove the two screws securing the UPS option slot cover plate, and then remove the cover plate.  
 
2.  Install the UPS Network Module along the alignment channels in the option slot.  
 
3.  Se cure the UPS Network Module using the two screws removed in...