HP Proliant Dl360 Generation 5 Server User Guide

							
 
Operations 21 
c.
 
Lift the assembly to unseat the PCI  riser boards and remove the assembly. 
  
Install the PCI riser board assembly 
  CAUTION:   To prevent damage to the server or expansio n boards, power down the server and remove all 
AC power cords before removing or inst alling the PCI riser board assembly. 
1. Align the PCI riser boards with the corresponding  connectors on the system board and install the 
assembly. 
2.  Tighten the four PCI riser bo ard assembly thumbscrews. 
  
Remove the power supply air baffle 
1. Power down the server (on page  18). 
2. Extend or remove the server from the rack ( Extend the server from the rack on page 19). 
3. Remove the access panel (on page  20).  
						

							
 
Operations 22 
4.
 
Remove the air baffle. 
  
Remove the processor air baffle 
1. Power down the server (on page  18). 
2. Extend or remove the server from the rack ( Extend the server from the rack on page 19). 
3. Remove the access panel (on page  20). 
4. Remove the air baffle. 
  
Remove and install a fan module 
The server has three fan modules ( Fan locations on page 17). 
To remove a fan module: 
1.  Power down the server (on page  18).  
						

							
 
Operations 23 
2.
 
Extend or remove the server from the rack ( Extend the server from the rack on page 19). 
3. Remove the access panel (on page  20). 
4. To remove fan module 1: 
a. Remove the power supply air baffle (on page  21). 
b. Remove fan module 1. 
 
5.  To remove fan module 2 or 3: 
a. Remove the processor air baffle (on page  22). 
b. Remove fan module 2 or 3. 
 
To install a fan module, reverse the removal procedures.  
						

							
 
Operations 24 
   IMPORTANT:   After installing the fan module, firmly press  the top of the module connectors to ensure the 
connectors are seated properly. 
  
						

							
 
Setup 25 
Setup 
In this section 
Optional installa tion services ........................................................................\
......................... .................. 25 
Rack planning  resources ........................................................................\
................................ ................. 26 
Optimum envi ronment........................................................................\
.................................... ................. 26 
Rack warnings ........................................................................\
.......................................... ..................... 28 
Contents of the serv er shipping carton ........................................................................\
................. ............. 28 
Installing hard ware options ........................................................................\
............................ ................. 28 
Installing the serv er into the rack ........................................................................\
.................... .................. 28 
Powering up and conf iguring the server ........................................................................\
................. ........... 30 
Installing the op erating system ........................................................................\
........................ ................. 30 
Registering  the server........................................................................\
................................. ..................... 31 
 
Optional installation services 
Delivered by experienced, certified engineers, HP Care Pack servic es help you keep your servers up and 
running with support packages tailor ed specifically for HP ProLiant systems. HP Care Packs let you 
integrate both hardware and software support into  a single package. A number of service level options 
are available to meet your needs.  
HP Care Pack Services offer upgraded service levels  to expand your standard product warranty with easy-
to-buy, easy-to-use support packages that help you make  the most of your server investments. Some of the 
Care Pack services are: 
•  Hardware support 
• 6-Hour Call-to-Repair 
• 4-Hour 24x7 Same Day 
• 4-Hour Same Business Day 
• Software support 
• Microsoft® 
• Linux 
• HP ProLiant Essentials (HP SIM and RDP) 
• VMWare 
• Integrated hardware and software support 
• Critical Service 
• Proactive 24 
• Support Plus 
• Support Plus 24 
• Startup and implementation services for both hardware and software 
For more information on Care Packs, refer to the HP website 
( http://www.hp.com/hps/carepa ck/servers/cp_proliant.html
).   
						

							
 
Setup 26 
Rack planning resources 
The rack resource kit ships with all HP branded or  Compaq branded 9000, 10000, and H9 series racks. 
For more information on the content of each resour ce, refer to the rack resource kit documentation. 
If you intend to deploy and configur e multiple servers in a single rack, refer to the white paper on high-
density deployment at the HP website ( http://www.hp.com/products/servers/platforms
).  
Optimum environment 
When installing the server in a rack, select a locati on that meets the environmental standards described in 
this section. 
 
Space and airflow requirements 
To allow for servicing and adequate airflow, observe  the following space and airflow requirements when 
deciding where to install a rack: 
•  Leave a minimum clearance of 63.5 cm (25 in) in front of the rack. 
• Leave a minimum clearance of 76.2 cm (30 in) behind the rack. 
• Leave a minimum clearance of 121.9 cm (48 in) fr om the back of the rack to the back of another 
rack or row of racks. 
HP servers draw in cool air through the front door  and expel warm air through the rear door. Therefore, 
the front and rear rack doors must be adequately ve ntilated to allow ambient room air to enter the 
cabinet, and the rear door must be adequately vent ilated to allow the warm air to escape from the 
cabinet. 
   CAUTION:   To prevent improper cooling and damage to  the equipment, do not block the ventilation 
openings. 
When vertical space in the rack is not filled by  a server or rack component, the gaps between the 
components cause changes in airflow through the  rack and across the servers. Cover all gaps with 
blanking panels to main tain proper airflow. 
  CAUTION:   Always use blanking panels to fill empty vertic al spaces in the rack. This arrangement ensures 
proper airflow. Using a rack without blanking panels re sults in improper cooling that can lead to thermal 
damage. 
The 9000 and 10000 Series Racks provide proper server cooling from flow-through perforations in the 
front and rear doors that provide 64 pe rcent open area for ventilation.  
  CAUTION:   When using a Compaq branded 7000 Series rack,  you must install the high airflow rack door 
insert [P/N 327281-B21 (42U) or P/N 157847-B21 (22U )] to provide proper front-to-back airflow and 
cooling. 
   CAUTION:   If a third-party rack is used, observe the follo wing additional requirements to ensure adequate 
airflow and to prevent damage to the equipment: 
•   Front and rear doors—If the 42U rack includes clos ing front and rear doors, you must allow 5,350 sq 
cm (830 sq in) of holes evenly distributed from top  to bottom to permit adequate airflow (equivalent to 
the required 64 percent open area for ventilation). 
•   Side—The clearance between the in stalled rack component and the side  panels of the rack must be a 
minimum of 7 cm (2.75 in). 
  
						

							
 
Setup 27 
Temperature requirements 
To ensure continued safe and reliable equipment oper ation, install or position the system in a well-
ventilated, climate-controlled environment. 
The maximum recommended ambient operating temperat ure (TMRA) for most server products is 35°C 
(95°F). The temperature in the room where the rack is located must not exceed 35°C (95°F). 
   CAUTION:   To reduce the risk of damage to the eq uipment when installing third-party options: 
•   Do not permit optional equipment to  impede airflow around the server or to increase the internal rack 
temperature beyond the maximum allowable limits. 
•   Do not exceed the manufacturer’s TMRA. 
 
Power requirements 
Installation of this equipment must comply with lo cal and regional electrical regulations governing the 
installation of information technolo gy equipment by licensed electricia ns. This equipment is designed to 
operate in installations covered by NFPA 70, 1999  Edition (National Electric Code) and NFPA-75, 1992 
(code for Protection of Electronic Computer/Data Proc essing Equipment). For electrical power ratings on 
options, refer to the product rating label or th e user documentation supplied with that option. 
  WARNING:  To reduce the risk of personal  injury, fire, or damage to the equipment, do 
not overload the AC supply branch circuit th at provides power to the rack. Consult the 
electrical authority having jurisdiction over  wiring and installation requirements of your 
facility.  
  CAUTION:   Protect the server from power fluctuations  and temporary interruptions with a regulating 
uninterruptible power supply (UPS). This device pr otects the hardware from damage caused by power 
surges and voltage spikes and keeps the syst em in operation during a power failure. 
When installing more than one server, you may need  to use additional power distribution devices to 
safely provide power to all devices.  Observe the following guidelines: 
• Balance the server power load between  available AC supply branch circuits. 
• Do not allow the overall system AC current load  to exceed 80 percent of the branch circuit AC 
current rating. 
•  Do not use common power outlet strips for this equipment. 
• Provide a separate electrical circuit for the server. 
For more information on the hot- plug power supply and calculators to determine server power 
consumption in various system configurations, re fer to the HP Enterprise Configurator website 
( http://h30099.www3.hp.com/configurator/
).  
Electrical grounding requirements 
The server must be grounded properly for proper op eration and safety. In the United States, you must 
install the equipment in accordance with NFPA 70,  1999 Edition (National Electric Code), Article 250, 
as well as any local and regional  building codes. In Canada, you must install the equipment in 
accordance with Canadian Standards Association, CS A C22.1, Canadian Electrical Code. In all other 
countries, you must install the equipment in accordance  with any regional or national electrical wiring 
codes, such as the International Electrotechnica l Commission (IEC) Code 364, parts 1 through 7. 
Furthermore, you must be sure that all power distributi on devices used in the installation, such as branch 
wiring and receptacles, are listed or  certified grounding-type devices. 
Because of the high ground-leakage  currents associated with multiple servers connected to the same 
power source, HP recommends the use of a PDU that is  either permanently wired to the building’s branch 
circuit or includes a nondetachable cord that is wired  to an industrial-style plug. NEMA locking-style plugs  
						

							
 
Setup 28 
or those complying with IEC 60309 are considered suit able for this purpose. Using common power outlet 
strips for the server is not recommended. 
 
Rack warnings 
   WARNING:  To reduce the risk of personal injury or damage to the equipment, be sure 
that:  
•   The leveling jacks are extended to the floor.  
•   The full weight of the rack rests on the leveling jacks.  
•   The stabilizing feet are attached to the ra ck if it is a single-rack installation.  
•   The racks are coupled together in  multiple-rack installations.  
•   Only one component is extended at a time.  A rack may become unstable if more than 
one component is extended for any reason.  
 
  WARNING:  To reduce the risk of personal  injury or equipment damage when unloading 
a rack:  
•   At least two people are needed to safely  unload the rack from the pallet. An empty 
42U rack can weigh as much as 115 kg (253  lb), can stand more than 2.1 m (7 ft) 
tall, and may become unstable when being moved on its casters.  
•   Never stand in front of the rack when it is rolling down the ramp from the pallet. 
Always handle the rack from both sides.  
 
Contents of the server shipping carton 
Unpack the server shipping carton and locate the mate rials and documentation necessary for installing the 
server. All the rack mounting hardware  necessary for installing the server into the rack is included with the 
rack or the server.  
The contents of the server shipping carton include: 
•  Server 
• Power cord 
• Printed setup documentation, Docume ntation CD, and software products 
• Rack mounting hardware  kit and documentation 
In addition to these supplied items, you may need: 
•  T-15 Torx screwdriver 
• Hardware options 
• Operating system or application software  
Installing hardware options 
Install any hardware options before initializing the serv er. For options installation information, refer to the 
option documentation. For server-specific information,  refer to Hardware options installation (on page 
32 ). 
 
Installing the server into the rack 
To install the server into a rack with square, round, or  threaded holes, refer to the instructions that ship 
with the rack hardware kit.  
						

							
 
Setup 29 
If you are installing the server into a telco rack, or der the appropriate option kit at the RackSolutions.com 
website ( http://www.racksolutions.com/hp
). Follow the server-specific instru ctions on the website to install 
the rack brackets. 
Use the following information when connecting peripheral cables and power cords to the server. 
   WARNING:  This server is very heavy. To redu ce the risk of personal injury or damage to 
the equipment: 
•   Observe local occupational health and safety  requirements and guidelines for manual 
material handling. 
•   Get help to lift and stabilize the product duri ng installation or removal, especially 
when the product is not fastened to the ra ils. When the server weighs more than 22.5 
kg (50 lb), at least two people must lift  the server into the rack together. A third 
person may be required to help align the serv er if the server is installed higher than 
chest level. 
•   Use caution when installing the server in or  removing the server from the rack; it is 
unstable when not fastened to the rails.  
  CAUTION:   Always plan the rack installation so that the he aviest item is on the bottom of the rack. Install 
the heaviest item first, and continue to po pulate the rack from the bottom to the top. 
1. Install the server and cable management arm into the  rack. Refer to the installation instructions that 
ship with the HP 1U Quick Deploy Rail System. 
2.  Connect the peripheral devices to the server. 
   
Item Description 
1  PCI Express expansion slot 1, low-profile, half-length 
2  PCI Express expansion slot 2 
3  Power supply bay 2 
4  Power supply bay 1 
5  NIC 2 connector 
6  NIC 1 connector 
7 Keyboard connector 
8 Mouse connector 
9 Video connector  
						

							
 
Setup 30 
Item Description 
10 Serial connector 
11 USB connector 
12 USB connector 
13  iLO 2 NIC connector  
3.
 Use the strain relief clip from the server  hardware kit to secure the power cord. 
  
Powering up and configuring the server 
To power up the server, press the Power On/Standby button. 
While the server boots, RBSU and the ORCA utility ar e automatically configured to prepare the server for 
operating system installation.  
To configure these utilities manually: 
•  Press the  F8 key when prompted during the array controller initialization to configure the array 
controller using ORCA. 
•  Press the  F9 key when prompted during the boot process  to change the server settings using RBSU. 
The system is set up by default for the English language. 
For more information on the automa tic configuration, refer to the HP ROM-Based Setup Utility User Guide  
located on the Documentation CD. 
 
Installing the operating system 
To operate properly, the server must have a suppor ted operating system. For the latest information on 
supported operating systems, refer to the HP website ( http://www.hp.com/go/supportos
). 
Two methods are available to install  an operating system on the server: 
• SmartStart assisted installation—Insert the SmartS tart CD into the CD-ROM drive and reboot the 
server.