HP Photosmart B109n User Manual

4.Run your finger along the top of the ink cartridges to locate any cartridges that
are not snapped completely down.
5.Press down on any cartridges that are sticking up.
They should snap down into place.
6.If an ink cartridge was sticking up and you were able to snap it back down into
place, close the ink cartridge access door and check if the error message has
gone away.
• If the message has gone away, stop troubleshooting here. The error has been
resolved.
• If the message has not gone away, proceed to...

11.Reinstall the ink cartridge.
It should now snap down into place.
12.Close the ink cartridge access door, and check if the error message has gone
away.
13.If you still receive the error message, turn the product off, and then on again.
Cause:The ink cartridges were not installed properly.
If this did not solve the issue, try the next solution.
Solution 3: Contact HP support
Solution:Contact HP support for service.
Go to: www.hp.com/support.
If prompted, choose your country/region, and then click...

HP recommends that you use genuine HP ink cartridges. Genuine HP ink cartridges
are designed and tested with HP printers to help you easily produce great results,
time after time.
NOTE:HP cannot guarantee the quality or reliability of non-HP supplies. Printer
service or repairs required as a result of using a non-HP supply will not be covered
under warranty.
If you believe you purchased genuine HP ink cartridges, go to:
www.hp.com/go/anticounterfeit
For more information, see:
“Replace the cartridges” on...

Previously used genuine HP cartridge
Solution:Check the print quality of the current print job. If it is not satisfactory, try
cleaning the printhead to see if that improves the quality.
To clean the printhead from the HP Photosmart Software
1.Load letter, A4, or legal unused plain white paper into the paper tray.
2.In the HP Solution Center, click Settings.
3.In the Print Settings area, click Printer Toolbox.
NOTE:You can also open the Printer Toolbox from the Print Properties
dialog box. In the Print...

3.Remove all of the ink cartridges and place them on a piece of paper with the ink
opening pointing up.
4.Lift the latch handle on the print carriage until it stops.
5.Remove the printhead by lifting it straight up.
Chapter 12
92 Solve a problem
Solve a problem
 

6.Clean the printhead.
There are three areas of the printhead that need to be cleaned: the plastic ramps
on both sides of the ink nozzles, the edge between the nozzles and the electrical
contacts, and the electrical contacts.
1Plastic ramps on the sides of the nozzles
2Edge between nozzles and contacts
3Electrical contacts
CAUTION:Touch the nozzle and the electrical contact areas only with
cleaning materials and not with your finger.
To clean the printhead
a. Lightly dampen a clean, lint-free cloth and...

b. Use a fresh, lightly dampened, lint-free cloth to wipe any accumulated ink and
debris from the edge between the nozzles and the contacts.
c. Use a fresh, lightly dampened, lint-free cloth to wipe the plastic ramps on both
sides of the nozzles. Wipe away from the nozzles.
d. Wipe the previously cleaned areas dry with a dry lint-free cloth before
proceeding to the next step.
7.Clean the electrical contacts inside the product.
To clean the electrical contacts in the product
a. Lightly dampen a clean,...

c. Wipe the area dry with a dry lint-free cloth before proceeding to the next step.
8.Make sure the latch handle is raised, and then reinsert the printhead.
9.Carefully lower the latch handle.
NOTE:Make sure you lower the latch handle before reinserting the ink
cartridges. Leaving the latch handle raised can result in incorrectly seated ink
cartridges and problems printing. The latch must remain down in order to
correctly install the ink cartridges.
10.Using the colored shaped icons for help, slide the...

11.Close the ink cartridge door.
Cause:There was a problem with the printhead.
If this did not solve the issue, try the next solution.
Solution 2: Contact HP support
Solution:Contact HP support for service.
Go to: www.hp.com/support.
If prompted, choose your country/region, and then click Contact HP for information
on calling for technical support.
Cause:There was a problem with the printhead.
Problem with printer preparation
Solution:Check the print quality of the current print job. If it is not...

5.Click Clean the printhead.
6.Follow the prompts until you are satisfied with the quality of the output, and then
click Done.
There are two stages of cleaning. Each stage lasts about two minutes, uses one
sheet of paper, and uses an increasing amount of ink. After each stage, review
the quality of the printed page. You should only initiate the next phase of cleaning
if the print quality is poor.
If print quality still seems poor after you complete both stages of cleaning, try
aligning the printer. If...