HP Photosmart B109c User Manual

							Previously used genuine HP cartridge
Solution:Check the print quality of the current print job. If it is not satisfactory, try
cleaning the printhead to see if that improves the quality.
To clean the printhead from the HP Photosmart Software
1.Load letter, A4, or legal unused plain white paper into the paper tray.
2.In the HP Solution Center, click Settings.
3.In the Print Settings area, click Printer Toolbox.
NOTE:You can also open the Printer Toolbox from the Print Properties
dialog box. In the Print Properties dialog box, click the Features tab, and
then click Printer Services.
The Printer Toolbox appears.
4.Click the Device Services tab.
5.Click Clean the printhead.
6.Follow the prompts until you are satisfied with the quality of the output, and then
click Done.
There are two stages of cleaning. Each stage lasts about two minutes, uses one
sheet of paper, and uses an increasing amount of ink. After each stage, review
the quality of the printed page. You should only initiate the next phase of cleaning
if the print quality is poor.
If print quality still seems poor after you complete both stages of cleaning, try
aligning the printer. If print quality problems persist after cleaning and aligning,
contact HP support.
Follow the prompts on the display or computer screen to continue.
NOTE:HP recommends that you do not leave the ink cartridge outside of the
printer for an extended period of time. If a used cartridge is installed, check the
print quality. If it is not satisfactory, run the cleaning procedure from the toolbox.
Cause:The genuine HP ink cartridge was previously used in some other product.
Printhead problem
Try the following solutions.
•
Solution 1: Reinstall the printhead
•
Solution 2: Contact HP support
Solution 1: Reinstall the printhead
Solution:Check to make sure the printhead is installed and the ink cartridge access
door is closed.
Errors 89
Solve a problem
 
						

							Reinstall the printhead.
To reinstall the printhead
1.Make sure that the product is turned on.
2.Open the ink cartridge door.
3.Remove all of the ink cartridges and place them on a piece of paper with the ink
opening pointing up.
4.Lift the latch handle on the print carriage until it stops.
Chapter 11
90 Solve a problem
Solve a problem
 
						

							5.Remove the printhead by lifting it straight up.
6.Clean the printhead.
There are three areas of the printhead that need to be cleaned: the plastic ramps
on both sides of the ink nozzles, the edge between the nozzles and the electrical
contacts, and the electrical contacts.
1Plastic ramps on the sides of the nozzles
2Edge between nozzles and contacts
3Electrical contacts
CAUTION:Touch the nozzle and the electrical contact areas only with
cleaning materials and not with your finger.
Errors 91
Solve a problem
 
						

							To clean the printhead
a. Lightly dampen a clean, lint-free cloth and wipe the electrical contact area
from the bottom to the top. Do not go past the edge between the nozzles and
the electrical contacts. Clean until no new ink shows on the cloth.
b. Use a fresh, lightly dampened, lint-free cloth to wipe any accumulated ink and
debris from the edge between the nozzles and the contacts.
c. Use a fresh, lightly dampened, lint-free cloth to wipe the plastic ramps on both
sides of the nozzles. Wipe away from the nozzles.
d. Wipe the previously cleaned areas dry with a dry lint-free cloth before
proceeding to the next step.
Chapter 11
92 Solve a problem
Solve a problem
 
						

							7.Clean the electrical contacts inside the product.
To clean the electrical contacts in the product
a. Lightly dampen a clean, lint-free cloth with bottled or distilled water.
b. Clean the electrical contacts in the product by wiping with the cloth from top
to bottom. Use as many fresh, clean cloths as necessary. Clean until no ink
shows on the cloth.
c. Wipe the area dry with a dry lint-free cloth before proceeding to the next step.
8.Make sure the latch handle is raised, and then reinsert the printhead.
9.Carefully lower the latch handle.
NOTE:Make sure you lower the latch handle before reinserting the ink
cartridges. Leaving the latch handle raised can result in incorrectly seated ink
cartridges and problems printing. The latch must remain down in order to
correctly install the ink cartridges.
Errors 93
Solve a problem
 
						

							10.Using the colored shaped icons for help, slide the ink cartridge into the empty slot
until it clicks into place and is seated firmly in the slot.
11.Close the ink cartridge door.
Cause:There was a problem with the printhead.
If this did not solve the issue, try the next solution.
Solution 2: Contact HP support
Solution:Contact HP support for service.
Go to: 
www.hp.com/support.
If prompted, choose your country/region, and then click Contact HP for information
on calling for technical support.
Cause:There was a problem with the printhead.
Chapter 11
94 Solve a problem
Solve a problem
 
						

							Problem with printer preparation
Solution:Check the print quality of the current print job. If it is not satisfactory, it
could mean the internal clock failed and the product was not able to service the
printhead as scheduled. Try cleaning the printhead to see if that improves the quality.
To clean the printhead from the HP Photosmart Software
1.Load letter, A4, or legal unused plain white paper into the paper tray.
2.In the HP Solution Center, click Settings.
3.In the Print Settings area, click Printer Toolbox.
NOTE:You can also open the Printer Toolbox from the Print Properties
dialog box. In the Print Properties dialog box, click the Features tab, and
then click Printer Services.
The Printer Toolbox appears.
4.Click the Device Services tab.
5.Click Clean the printhead.
6.Follow the prompts until you are satisfied with the quality of the output, and then
click Done.
There are two stages of cleaning. Each stage lasts about two minutes, uses one
sheet of paper, and uses an increasing amount of ink. After each stage, review
the quality of the printed page. You should only initiate the next phase of cleaning
if the print quality is poor.
If print quality still seems poor after you complete both stages of cleaning, try
aligning the printer. If print quality problems persist after cleaning and aligning,
contact HP support.
Cause:The product was turned off improperly.
Errors 95
Solve a problem
 
						

							Chapter 11
96 Solve a problem
Solve a problem
 
						

							12 Stop the current job
To stop a current job from the product
▲Press Cancel on the control panel. If the current job does not stop, press Cancel
again.
It can take a few moments for the current job to be cancelled.
Stop the current job 97
Stop the current job
 
						

							Chapter 12
98 Stop the current job
Stop the current job