HP Pavilion G6 User Manual

							Power connector 
DescriptionSpare part number
Power connector641137-001
Before removing the power connector cable, remove the following components:
1.Battery (see 
Battery on page 43)
2.Service access cover (see 
Service access cover on page 44)
3.Hard drive (see 
Hard drive on page 45)
4.Optical drive (see 
Optical drive on page 47)
5.Keyboard (see 
Keyboard on page 52)
6.Top cover (see 
Top cover on page 55)
Remove the power connector:
1.Position the computer right-side up.
2.Disconnect the power connector cable (1) from the system board.
3.Lift the power connector (2) away from the clips built into the base enclosure.
Reverse this procedure to install the power connector.
Component replacement procedures 63 
						

							Display assembly
DescriptionSpare part number
39.6-cm (15.6-in) High Definition (HD), light-emitting diode (LED) BrightView display assembly:
●For use in Charcoal Grey computer models 645523-001
●For use in Ocean Drive computer models 636378-001
●For use in Sonoma Red computer models 645521-001
●For use in Luminous Rose computer models 645522-001
●For use in Pewter computer models 645524-001
●For use in Pacific Blue computer models 645525-001
●For use in Pearl Pink computer models 645526-001
●For use in Sweet Purple computer models 645527-001
●For use in Butter Gold computer models 645528-001
Before removing the display assembly, remove the following components:
1.Battery (see 
Battery on page 43)
2.Service access cover (see 
Service access cover on page 44)
3.Optical drive (see 
Optical drive on page 47)
4.WLAN module (see 
WLAN module on page 49)
5.Keyboard (see 
Keyboard on page 52)
6.Top cover (see 
Top cover on page 55)
7.USB board (see 
USB board on page 62)
8.Power connector (see 
Power connector on page 63)
Remove the display assembly:
1.Position the computer display-side up, with the front toward you.
2.Open the display as far as possible.
3.Disconnect the display panel cable (1) from the system board.
4.Pull the antenna cables through the opening in the base enclosure (2), and then disengage the
cables from the clip in the routing channel leading to the display hinge.
CAUTION:Support the display assembly when removing the display screws in the following
steps. Failure to support the display assembly can result in damage to the assembly and other
components.
5.Remove the two Phillips 6.0×2.5 screws (3) that secure the display assembly to the computer.
64 Chapter 4   Removal and replacement procedures 
						

							6.Lift the display panel (4) straight up to remove it.
NOTE:The security bracket is part of the right hinge.
Reverse this procedure to install the display assembly.
Component replacement procedures 65 
						

							7.To replace any of the display assembly internal components, remove the following screw covers
and screws:
(1) Two Mylar screw covers on the display bezel bottom edge
(2) Two Phillips 5.0×2.5 screws
8.Flex the inside edge of the left side (1), the top and bottom sides (2), and the right side (3) of the
display bezel until the bezel disengages from the display back cover.
9.Remove the display bezel (4). 
Reverse this procedure to install the display bezel.
66 Chapter 4   Removal and replacement procedures 
						

							10.To replace the webcam module, lift the webcam module as far from the display enclosure as the
webcam module cable allows.
11.Disconnect the webcam module cable (1) from the webcam module, and then remove the
webcam module (2). The webcam module is available using spare part number 637197-001. 
Reverse this procedure to install the webcam module.
12.To replace the display hinge covers, remove the two Phillips 3.0×2.5 screws (1) that secure the
covers to the display enclosure.
Component replacement procedures 67 
						

							13.Remove the display hinge covers (2). The display hinge covers are available using spare part
number 641142-001.
Reverse this procedure to install the display hinge covers.
14.To replace the display panel, remove four Phillips 4.0×2.5 screws that secure the display panel
to the display enclosure.
15.Tilt the display (1) up, release the tape (2) holding the display cable to the display panel, and
then disconnect the cable (3).
68 Chapter 4   Removal and replacement procedures 
						

							16.Remove the display panel (4) from the display enclosure. The display panel is available using
spare part number 647623-001 .
Reverse this procedure to install the display panel.
17.To replace the display panel brackets, remove the two Phillips PM 3.0×2.0 screws (1) that
secure each bracket to the display panel.
18.Remove the display brackets (2) from the display panel. The display brackets are available using
spare part number 637191-001.
Reverse this procedure to install the display hinges.
19.To replace the wireless transceivers, lift up on the silver transceivers (1), and then release the
adhesive material from the display cover.
Component replacement procedures 69 
						

							20.Lift up to remove the transceiver cable(2). The wireless antenna transceivers and cable are
available using spare part number 637185-001.
Reverse this procedure to install the display wireless antenna transceivers.
21.To remove the display cable from the display enclosure, lift the adhesive tabs (1) that hold the
display cable to the display enclosure. Gently peel the display cable (2) away from the adhesive
that holds the cable to the display panel.
Reverse this procedure to install the display panel.
70 Chapter 4   Removal and replacement procedures 
						

							System board
NOTE:The system board spare part kit includes UMA or discrete graphics subsystem memory and
replacement thermal material.
DescriptionSpare part number
For use in Intel HM55 UMA computer models 636370-001
For use in Intel HM65 UMA computer models 636373-001
For use in Intel HM55 discrete, 512 MB computer models 636371-001
For use in Intel HM55 discrete, 1 GB computer models 636372-001
For use in Intel HM65 discrete, 512 MB computer models 636374-001
For use in Intel HM65 discrete, 1 GB computer models 636375-001
For use in AMD UMA computer models 638856-001
For use in AMD discrete, 6470M, 512 MB computer models 638854-001
For use in AMD discrete, 6470M, 1 GB computer models 638855-001
When replacing the system board, be sure that the following components are removed from the
defective system board and installed on the replacement system board:
●Memory modules (see 
Memory module on page 51)
●WLAN module (see 
WLAN module on page 49)
Before removing the system board, remove the following components:
1.Battery (see 
Battery on page 43)
2.Service access cover (see 
Service access cover on page 44)
3.Hard drive (see 
Hard drive on page 45)
4.Optical drive (see 
Optical drive on page 47)
5.WLAN module (see 
WLAN module on page 49)
6.Memory module (see 
Memory module on page 51)
7.Keyboard (see 
Keyboard on page 52)
8.Top cover (see 
Top cover on page 55)
9.USB board (see 
USB board on page 62)
10.Display assembly (see 
Display assembly on page 64)
11.Power connector (see 
Power connector on page 63)
12.TouchPad LED board (see 
TouchPad LED board on page 60)
Component replacement procedures 71 
						

							Remove the system board:
1.Disconnect the optical drive connector from the system board (1) .
2.Remove the Phillips 5.0×2.0 screw (2) that secures the system board to the base enclosure.
3.Lift the system board (3) from the right edge and pull it away from the base enclosure at an
angle.
For AMD computer models, see the following image.
For Intel computer models, see the following image.
72 Chapter 4   Removal and replacement procedures