HP Pavilion 15 Bc200 Notebook Pc Manual

							Cables and connectorsCAUTION:When servicing the computer, be sure that cables are placed in their proper locations during the 
reassembly process. Improper cable placement can damage the computer.
Cables must be handled with extreme care to avoid damage. Apply only the tension required to unseat or seat 
the cables during removal and insertion. Handle cables by the connector whenever possible. In all cases, avoid  bending, twisting, or tearing cables. Be sure that cables are routed in such a way that they cannot be caught or snagged by parts being removed or replaced. Handle 


						

							Grounding guidelines
Electrostatic discharge damage
Electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure determine the degree of sensitivity. Networks built into many integrated circuits provide some protection, but in many 
cases, ESD contains enough power to alter device parameters or melt silicon junctions.
A discharge of static electricity from a 

						

							Packaging and transporting guidelines
Follow these grounding guidelines when packaging and transporting equipment:


						

							Equipment guidelines
Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation.


						

							5Removal and replacement procedures for authorized service provider parts
CAUTION:Components described in this chapter should be accessed only by an authorized service provider. 
Accessing these parts can damage the computer or void the warranty.CAUTION:This computer does not have user-replaceable parts. Only HP authorized service providers should 
perform the removal and replacement procedures described here. Accessing the internal part could damage  the computer or void the warranty.
Component replacement procedures
NOTE:Details about your computer, including model, serial number, product key, and length of warranty, 
are on the service tag at the bottom of your computer. See 
Locating system information on page 14 for 
details. 
NOTE:HP continually improves and changes product parts. For complete and current information on 
supported parts for your computer, go to 
http://partsurfer.hp.com, select your country or region, and then 
follow the on-screen instructions.
There are as many as 61 screws that must be removed, replaced, and/or loosened when servicing the parts 
described in this chapter. Make special note of each screw size and location during removal and replacement.
Base enclosure
DescriptionSpare part numberBase enclosure In Natural Silver 

						

							2.Remove the rubber strip (1), and then remove 10 Phillips 2x5 screws (2) and (3).
3.Slide a nylon 

						

							Display assemblyIMPORTANT:Make special note of each screw and screw lock size and location during removal 
and replacement.
Before removing the display assembly, follow these steps:
1.Shut down the computer.
2.Disconnect all external devices connected to the computer.
3.Disconnect the power from the computer by 

						

							2.Disconnect the WLAN antenna cable (1), and remove the tape holding it in place (2), disconnect the 
display cable 
(3), and then release the cable from the routing channels (4).
3.Rotate the display assembly (1), and then remove the display assembly from the base enclosure (2).
Reverse this procedure to install the display assembly.
30Chapter 5   Removal and replacement procedures for authorized service provider parts 
						

							Hard driveDescriptionSpare part numberHard drive 1 TB 7200 RPM SATA RAW 9.5mm766644-0052 TB 5400 RPM SATA RAW 9.5 mm801808-005Hard drive bracket913937-001Hard drive cable858969-001IMPORTANT:Make special note of each screw and screw lock size and location during removal 
and replacement.
Before removing the hard drive, follow these steps:
1.Shut down the computer.
2.Disconnect all external devices connected to the computer.
3.Disconnect the power from the computer by 

						

							Reverse this procedure to install the hard drive.
If it is necessary to disassemble the hard drive, follow these steps:

xRemove the hard drive connector (1), and then remove the side brackets (2).
Reverse this procedure to reassemble the hard drive.
32Chapter 5   Removal and replacement procedures for authorized service provider parts