HP LaserJet P4015n User Manual

Configure Device menu
Use this menu to change the default printing settings, adjust the print quality, and change the system
configuration and I/O options. 
Printing submenu
Some items on this menu are available in the program or printer driver. Program and printer-driver
settings override control-panel settings. In general, it is better to change these settings in the printer
driver, if applicable.
ItemValuesExplanation
COPIES1 to 32000Set the default number of copies by selecting any number from 1
to...

ItemValuesExplanation
YESThe default setting is YES.
MANUAL FEEDOFF
ONFeeds the paper manually from Tray 1, rather than automatically
from another tray. If MANUAL FEED=ON and Tray 1 is empty,
the product goes offline when it receives a print job. MANUALLY
FEED [PAPER SIZE] appears on the control-panel display.
The default setting is OFF.
COURIER FONTREGULAR
DARKSelects the version of Courier font to use:
REGULAR: The internal Courier font that is available on the
HP LaserJet 4 series products.
DARK: The...

ItemValuesExplanation
PCL SUBMENU FORM LENGTHSets vertical spacing from 5 to 128 lines for default paper size.
ORIENTATIONSets the default page orientation as LANDSCAPE or
PORTRAIT.
NOTE:It is best to set the page orientation in the program or
printer driver. (Program and printer-driver settings override
control-panel settings.)
FONT SOURCESelect the font source as INTERNAL, or EIO DISK. 
FONT NUMBERThe product assigns a number to each font and lists the numbers
on the PCL Font List. The font number...

Print Quality submenu
Some items on this menu are available in the program or printer driver. Program and printer-driver
settings override control-panel settings. In general, it is best to change these settings in the printer driver,
if applicable.
ItemValuesExplanation
SET REGISTRATIONPRINT TEST PAGE
SOURCE
ADJUST TRAY [N]Shifts the margin alignment to center the image on the page
from top to bottom, and left to right. You can also align the
image that is printed on the front with the image that is...

ItemValuesExplanation
CAUTION:Do not change the fuser mode for
transparencies. Failure to use the LIGHT2 setting while
printing transparencies can result in permanent damage to the
product and fuser. Always select Transparencies as the type
in the print driver and set the tray type at the product control
panel to TRANSPARENCY.
When selected, RESTORE MODES resets the fuser mode for
each paper type back to its default setting.
OPTIMIZE
Optimizes certain parameters
for all jobs rather than (or in
addition...

ItemValuesExplanation
NOTE:It is best to turn EconoMode on or off in the program
or printer driver. (Program and printer-driver settings override
control-panel settings.)
The default setting is OFF.
TONER DENSITY1 to 5Lighten or darken the print on the page by setting the toner
density. Select a setting ranging from 1 (light) to 5 (dark). The
default setting of 3 usually produces the best results.
AUTO CLEANINGOFF
ONUse this feature to automatically clean the paper path after the
product has printed a...

System Setup submenu
Items on this menu affect product behavior. Configure the product according to your printing needs.
ItemValuesExplanation
DATE/TIMEDATE
DATE FORMAT
TIME
TIME FORMATSets the date and time settings.
JOB STORAGE LIMIT1 to 100Specifies the number of quick copy jobs that can be stored on
the product.  
The default setting is 32.
JOB HELD TIMEOUTOFF
1 HOUR
4 HOURS
1 DAY
1 WEEKSets the amount of time that held jobs are kept before being
automatically deleted from the queue.
The default...

ItemValuesExplanation
TRAY BEHAVIORUSE REQUESTED TRAYSelect whether the product tries to pull paper from a different
tray than the one that you selected in the print driver.
●EXCLUSIVELY: Sets the product to pull from the tray that
you selected and not pull from another tray, even if the
tray that you selected is empty.
●FIRST: Sets the product to pull from the tray that you
selected first, but allows the product to pull from another
tray automatically if the tray that you selected is empty.
MANUALLY...

ItemValuesExplanation
4 HOURSThe product automatically comes out of Sleep mode when you
send a print job, press a product control-panel button, open a
tray, or open the top cover.
The default setting is 30 MINUTES.
WAKE TIMEMONDAY
TUESDAY
WEDNESDAY
THURSDAY
FRIDAY
SATURDAY
SUNDAYSets a “wake-up” time for the product to warm up each day.
The default for each day is OFF. If you set a wake time, HP
recommends setting an extended sleep delay time period, so
that the product will not return to sleep mode soon...

ItemValuesExplanation
STOP AT OUT: The product stops printing when the print
cartridge is depleted. You must replace the print cartridge
before printing can continue.
OVERRIDE AT OUT: Select this option to override the
message and continue printing after the print cartridge is
depleted. HP does not guarantee print quality after you select
this option.
The default value is OVERRIDE AT OUT.
ORDER AT1 TO 100Set the threshold at which the ORDER BLACK CARTRIDGE
message appears. The value is the percent of...