HP LaserJet M4345xm User Manual

Label construction
When selecting labels, consider the quality of each component:
●Adhesives:
 The adhesive material should be stable at 200C (392F), the printers fusing
temperature.
● Arrangement:
 Only use labels with no exposed backing between them. Labels can peel off
sheets with spaces between the labels, causing serious jams.
● Curl:
 Prior to printing, labels must lie flat with  no more than 13mm (0.5inch) of curl in any
direction.
● Condition:
 Do not use labels with wrinkles, bubbles, or other...

Card stock guidelines
Set margins at least 2mm (0.08in.) away from the edges.
Letterhead and preprinted forms
Many manufacturers now offer premium paper advertised as laser-compatible or laser-guaranteed.
Some of the rougher surface finishes, such as cockle, laid, or linen, might require the special fuser
modes that are available on some printer models in order to achieve adequate toner adhesion.
NOTESome page-to-page variation is normal when printing with laser printers. This
variation cannot be...

Media typeFuser mode setting
PlainNormal
PreprintedNormal
LetterheadNormal
TransparencyLow 2
PrepunchedNormal
LabelsNormal
BondNormal
RecycledNormal
ColorNormal
LightLow 1
Card stockNormal
RoughHigh 1
EnvelopeNormal
To reset the fuser modes to the default settings, touch the Administration menu at the device control
panel. Touch  Print Quality, touch Fuser Modes , and then touch  Restore Modes.
ENWW Media considerations 71
 

Select print media
Table 4-1  Supported types of media
Type of mediaTray1Trays 2, 3,
4, and 5Optional duplexerOptional
envelope feeder3-bin mailbox or
stacker part of
stapler/stackerStapler part of
stapler/stacker
PlainXXXXXX
PreprintedXXXXXX
LetterheadXXXXXX
TransparencyXX  X 
PrepunchedXXXXX
LabelsXXXXX 
BondXXXXXX
RecycledXXXXXX
ColorXXXXXX
CardstockX  XX 1 2 
RoughXXXXXX
EnvelopeX  XX1 
1Face-up delivery only.2If a 3-bin mailbox is installed, select the bottom bin when printing on cardstock. Media...

SizeDimensions1WeightCapacity2
Envelope Commercial #10105x241mm (4.1x9.5inches)75to105g/m2 (20to28lb)10envelopes
EnvelopeDL ISO110x220mm (4.3x8.7inches)
EnvelopeC5 ISO162x229mm (6.4x9.0inches)
EnvelopeB5 ISO176x250mm (6.9x9.8inches)
EnvelopeMonarch #7-3/498x191mm (3.9x7.5inches)
1The MFP supports a wide range of sizes. Check the MFP software for supported sizes.2Capacity can vary depending on paper weight and thickness, as well as environmental conditions.3To print on custom-size paper, see Load small...

Table 4-4  Optional duplexer supported sizes and weights 
SizeDimensionsWeight
Letter216x279mm (8.5x11inches)60to120g/m2 (16to32lb)
A4
210x297mm (8.3x11.7inches)
Executive184x267mm (7.3x10.5inches)
Legal216x356mm (8.5x14inches)
B5 (JIS)182x257mm (7.2x10.1inches)
A5148 x 210 mm (5.8x8.3inches)
8.5x13216x330mm (8.5x13inches)
Executive (JIS)216x330mm (8.5x13inches)
16K 197x273mm (7.75x10.75inches)
Table 4-5  Optional envelope feeder supported sizes and weights 
SizeDimensionsWeightCapacity
Monarch...

Table 4-6  Optional 3-bin mailbox or stacker part of the stapler/stacker supported sizes and weights    
SizeDimensions1WeightCapacity2
Letter216x279mm (8.5x11inches) For the stacker on the stapler/
stacker or the lower bin on the
3-bin mailbox: 500sheets of 75g/
m
2 (20lb) paper
For the top two bins on the 3-
bin mailbox: each can hold
100sheets of 75g/m
2 (20lb)
paper.
A4210x297mm (8.3x11.7inches)
Executive184x267mm (7.3x10.5inches)
Legal216x356mm (8.5x14inches)
B5 (JIS)182x257mm (7.2x10.1inches)...

Table 4-8  ADF supported sizes and weights  
SizeDimensionsWeightCapacity
Letter216x279mm (8.5x11inches)60to120g/m2 (16to32lb) 50sheets of 75g/m2 (20lb) paper
A4
210x297mm (8.3x11.7inches)
A5148x210mm (5.8x8.3inches)
Legal 216x356mm (8.5x14inches)
76 Chapter 4   Media and trays ENWW
 

Printing and paper-storage environment
Ideally, the printing and paper-storage environment should be at or near room temperature, and not
too dry or too humid. Remember paper is  hygroscopic; it absorbs and loses moisture rapidly.
Heat works with humidity to damage paper. Heat causes the moisture in paper to evaporate, while
cold causes it to condense on the sheets. Heating  systems and air conditioners remove most of the
humidity from a room. As paper is opened and used, it loses moisture, causing...

Load media
This section contains information about loading standard- and custom-size media into the input trays.
CAUTIONTo avoid a jam, never add or remove paper from a tray while printing or copying
from that tray. To avoid damaging the MFP,  print labels and envelopes from tray1 only. Print
on only one side of labels, envelopes, and transparencies.
Load the flatbed scanner
Place the document face-down on the scanner glass.
Load the ADF
Load the document face-up in the ADF.
Load tray1
Tray1 holds up to...