HP LaserJet 3055 User Manual

Supported media weights and sizes
For optimum results, use conventional 75 to 90 g/m2 (20 to 24 lb) photocopy paper. Verify that the
paper is of good quality and is free of  cuts, nicks, tears, spots, loose particles, dust, wrinkles, curls,
and bent edges.
NOTE The all-in-one supports a wide range of standard and custom sizes of print media.
The capacity of trays and bins can vary depending on media weight and thickness and on
environmental conditions. Use only transparencies that are designed for use...

MediaDimensions1WeightCapacity2
Executive191 x 267 mm (7.3 x 10.5 inches)
8.5 x 13 inches216 x 330 mm (8.5 x 13 inches)
1The all-in-one supports a wide range of standard and custom sizes of print media. Check the printer driver for supported sizes.2Capacity can vary depending on the media weight and thickness, and environmental conditions.
Table 3-4  Single-sheet priority input slot specifications, HP LaserJet 3390/3392 all-in-one
MediaDimensions1WeightCapacity2
PaperMinimum: 76 x 127 mm
(3 x 5 inches)60...

Table 3-6  Automatic document feeder (ADF) specifications, HP LaserJet 3050 all-in-one
MediaDimensionsWeight or thicknessCapacity
Minimum size148 x 105 mm (5.83 x 4.13
inches)60 to 105 g/m2 (16 to 28 lb)30 sheets (80 g/m2or 20 lb bond)
Maximum size216 x 381 mm (8.5 x 15 inches)1
1For legal-sized (216 x 356 mm; 8.5 x 14 inches) and larger media, feed one sheet at a time through the ADF.
Table 3-7  ADF specifications, HP LaserJet 3052/3055/3390/3392 all-in-one
MediaDimensionsWeight or thicknessCapacity...

Printing and storage environment
Ideally, the printing and media-storage environment should be at or near room temperature, and not
too dry or too humid. Remember that  paper absorbs and loses moisture rapidly.
Heat works with humidity to damage paper. Heat causes the moisture in paper to evaporate, while
cold causes it to condense on the sheets. Heating  systems and air conditioners remove most of the
humidity from a room. As paper is opened and used, it loses moisture, causing streaks and
smudging....

4 Using the all-in-one
●Loading media into the input trays
●
Controlling print jobs
●
Using the all-in-one control panel
ENWW 37
 

Loading media into the input trays
The following sections describe how to load media into the different input trays.
CAUTIONPrinting on wrinkled, folded, or damaged media can cause jams. See Guidelines
for using media for more information.
Loading documents to fax, copy, or scan
Use these instructions to load originals into the all-in-one for scanning. For the best quality scans,
use the flatbed scanner.
To load originals onto the flatbed scanner (HP LaserJet 3052/3055/3390/3392 all-in-one only)
1.Make...

CAUTIONTo prevent damage to the all-in-one, do not use an original that contains
correction tape, correction fluid, paper clips, or staples. Also, do not load photographs, small
originals, or fragile originals into the ADF.
1. For the HP LaserJet 3050 all-in-one, insert  the top-end of the stack of originals into the ADF
input tray, with the media stack face-down and the first page to be copied at the bottom of the
stack.
Make sure that the ADF media lever is set correctly for single-page or...

Loading input trays, HP LaserJet 3050/3052/3055 all-in-one
Priority input slot
The priority input slot on the HP LaserJet 3050/3052/3055 all-in-one holds up to 10 sheets of media
up to 163 g/m2 (43 lb) in weight or one envelope, transparency, or card. Load media with the top
forward and the side to be printed facing up.  To prevent jams and skewing, always adjust the side
media guides before feeding the media.
250-sheet input tray (tray 1)
The input tray holds up to 250 pages of 80 g/m2 or 20 lb paper or...

Loading input trays, HP LaserJet 3390/3392 all-in-one
Single-sheet priority input slot (tray 1)
The single-sheet priority input slot on the HP LaserJet 3390/3392 all-in-one holds one sheet of media
up to 163 g/m2 (43 lb) in weight or one envelope, transparency,  or card. Load media with the top
forward and the side to be printed facing up. To prevent jams and skewing, always adjust the side
media guides before feeding the media.
NOTE When feeding media into the single-sheet  priority input slot on the HP...

Controlling print jobs
This section provides basic printing instructions. When making changes to printing settings, follow
the hierarchy of how changes are prioritized.
NOTEThe names of commands and dialog boxes might vary depending on your software
program.
Print-settings priorities
When making changes to printing settings, follow the hierarchy of how changes are prioritized. (Note
that the names of commands and dialog boxes might vary depending on your software program.)
● Page Setup dialog box
. This...