HP LaserJet 1018 User Manual

							
3. When you have removed the jammed media, replace the print cartridge, and close the
print cartridge door.
After clearing a media jam, you might need to turn the printer off and turn it back on
again.
NOTE
When you add new media, remove all of the media from the input tray and straighten the
stack of new media.
Return to 
Finding the solution .
ENWW Clearing jams73
 
						

							74Chapter 4 Problem solvingENWW
 
						

							
A
Printer specifications
This appendix provides information on the following topics:
●
Environmental specifications
●
Acoustic emissions
●
Electrical specifications
●
Physical specifications
●
Printer capacities and ratings
●
Memory specifications
ENWW 75
 
						

							
Environmental specifications
Operating environmentInstall in a well-ventilated, dust-free area.
Printer plugged into an AC outlet:
●Temperature: 10°C to 32.5°C (50°F to
90.5°F)
● Humidity: 20% to 80% (no condensation)
Storage environmentPrinter unplugged from an AC outlet:
●Temperature: 0°C to 40°C (32°F to 104°F)
● Humidity: 10% to 80% (no condensation)
NOTEValues are current as of April 1, 2004. Values are subject to change without notice. See
http://www.hp.com/support/lj1018/  for current information.
76 Appendix A Printer specifications ENWW
 
						

							
Acoustic emissions
Acoustic emissions1, 2
Sound power levelDeclared per ISO 9296
Printing3LWAd = 
						

							
Electrical specifications
WARNING!Power requirements are based on the country/region where the printer is sold. Do not
convert operating voltages. Doing so might damage  the printer and void the product warranty.
110-volt models230-volt models
Power requirements110-127v (+/-10%)
50/60 Hz (+/-2 Hz)220v-240v (+/-10%)
50/60 Hz (+/-2 Hz)
Rated current3.5 amps2.0 amps
Power consumption (average, in watts)1, 2
Product modelPrinting4Ready3, 5Off
HP LaserJet 1018250 W2 W0 W
1Values are subject to change without notice. See http://www.hp.com/support/lj1018/ for
current information.
2Power reported is the highest value measured  for monochrome printing using all standard
voltages.
3The default time from Ready mode to PowerSave mode and the recovery time from
PowerSave mode to the start of printing is  negligible (less than 10 seconds) because of the
instant-on fusing.
4HP LaserJet 1018 speed is 12 ppm for A4  media and 12 ppm for letter media.5The heat dissipation in Ready mode is 20 BTU/hour.
78 Appendix A Printer specifications ENWW
 
						

							
Physical specifications
Dimensions●Width: 370 mm (14.6 inches)
● Depth: 242 mm (9.5 inches)
● Height: 209 mm (8.2 inches)
Weight (2,000-page cartridge installed)5.8 kg (12.8 lb)
NOTEValues are current as of April 1, 2004. Values are subject to change without notice. See
http://www.hp.com/support/lj1018/  for current information.
ENWW Physical specifications79
 
						

							
Printer capacities and ratings
Print speed●12 ppm for A4 media and 12 ppm for letter
media
● First page out in as low as 10 seconds
Main input tray capacity150 sheets of regular weight 75 g/m2 (20 lb) paper
Priority feed slot capacity1 sheet of media up to 163 g/m2 (43 lb)
Top (face down) output bin capacity100 sheets of regular weight 75 g/m2 (20 lb) paper
Minimum paper size76 x 127 mm (3 x 5 inches)
Maximum paper size216 x 356 mm (8.5 x 14 inches)
Media weightOutput bin: 60 to 105 g/m2 (16 to 28 lbs)
Base memory2 MB of RAM
Print resolution●600 x 600 dpi with HP Resolution
Enhancement technology (REt)
● 1200 dpi effective output quality
(600 x 600 x 2 dpi with HP Resolution
Enhancement technology [REt])
Duty cycle●3,000 single-sided pages per month
(maximum)
● 1,000 single-sided pages per month
(average)
80 Appendix A Printer specifications ENWW
 
						

							
Memory specifications
Base memory2 MB RAM
ENWWMemory specifications81
 
						

							82Appendix A Printer specifications ENWW