HP Envy 2 Owners Manual

							7.Lift up on the top edge of the display.
NOTE:Support the display panel as you are removing the screws.
8.Locate the NFC antenna connector (1), disconnect the NFC antenna cable (2), and then remove
the NFC antenna (3).
Component replacement procedures 43 
						

							9.Disconnect the tablet battery cable (1), remove the 4 screws that secure the battery (2), and
then remove the tablet battery (3).
10.Release the display panel cable support strip (1), release the display panel cable tape (2), and
then disconnect the display panel cable (3).
44 Chapter 4   Removal and replacement procedures 
						

							11.Clear the routing channel and clips (4), and then remove the display panel (5).
12.Locate the display panel cable support strip (1), release the display panel cable tape (2), and
then disconnect the display panel cable (3).
Component replacement procedures 45 
						

							13.Lift up on the right side of the screen. From the left side, locate the 2 connectors (1), and then
release the connectors (2). Remove the touch screen (3)
Reverse this procedure to install the display panel.
System board
ComponentSpare part number
System board for use only with 128–GB tablet equipped with an Intel Z2760 1.8GHz processor
(includes processor and replacement thermal material)708759–001
System board (Windows 8 Standard) for use only with 128–GB tablet equipped with an Intel Z2760
1.8GHz processor (includes processor and replacement thermal material)708759–501
System board (Windows 8 Professional) for use only with 128–GB tablet equipped with an Intel
Z2760 1.8GHz processor (includes processor and replacement thermal material)708759–601
Before removing the system board, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.Disconnect all external devices connected to the computer.
3.Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
Remove the system board:
1.Disconnect the wireless antenna cable (1), the microphone board cable (2), and then disconnect
the webcam cables (3).
46 Chapter 4   Removal and replacement procedures 
						

							2.Disconnect the webcam light board cable (4), the power button board cable (5), and then
disconnect the right speaker cable (6).
3.Disconnect the volume control button board cable (1), the micro Digital Media Card Reader
board cable (2), and then disconnect the left speaker cable (3).
Component replacement procedures 47 
						

							4.Disconnect the stabilizer module cable (4), disconnect the docking connector board cable (5),
and then disconnect the touch screen connector board cable (6).
5.Remove the five screws securing the system board (1), and then remove the system board (2).
Reverse this procedure to install the system board.
48 Chapter 4   Removal and replacement procedures 
						

							Touch screen connector board
Description Spare part number
Touch screen connector board 702351–001
Before removing the touch screen connector board, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.Disconnect all external devices connected to the computer.
3.Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
Remove the Touch screen:
1.Locate the Touch Screen connector board (1) on the system board, and then disconnect the
touch screen connector board cable (2) from the system board.
2.Remove the screw securing the touch screen connector board (3), and then remove the touch
screen connector board (4).
Display bezel
DescriptionSpare part number
Display bezel (with antenna)702350-001
Component replacement procedures 49 
						

							Before removing the display bezel, follow these steps:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.Disconnect all external devices connected to the computer.
3.Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.Remove the base enclosure (see 
Base enclosure on page 28).
5.Remove the display panel, and display panel cable (see 
Display panel assembly and Battery
on page 40).
6.Remove the NFC antenna (see 
Display panel assembly and Battery on page 40).
7.Remove the touch screen (see 
Touch screen connector board on page 49).
Remove the display bezel:
1.Turn the tablet so that it faces forward.
2.Disconnect the left wireless antenna cable (1), and then disconnect the microphone board cable
(2).
3.Disconnect the right webcam cable (3), and then disconnect the webcam LED board cable (4)
4.Disconnect the front webcam cable (5), the front webcam light cable (6), and then disconnect the
Windows button cable (7).
50 Chapter 4   Removal and replacement procedures 
						

							5.Remove the ten screws securing the display bezel.
6.Release the bezels bottom edge (1), release the left and right edges (2), release the top edge
(3), and remove the display bezel (4).
Reverse this procedure to install the display bezel.
Webcam assembly (front)
Description Spare part numbers
Webcam assembly 702358-001
Before removing the webcam assembly:
1.Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.Disconnect all external devices connected to the computer.
3.Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.Remove the display panel (see 
Display panel assembly and Battery on page 40).
Component replacement procedures 51 
						

							5.Remove the base enclosure (see Base enclosure on page 28).
6.Remove the display bezel (see 
Display bezel on page 49).
Remove the front webcam assembly:
1.Remove the 2 screws securing the webcam LED board (1) to the display bezel, and then
remove the webcam LED board (2).
52 Chapter 4   Removal and replacement procedures