HP Designjet Z6200 1524 mm Photo User Manual

Table 4-1  Supported paper types (continued)
Paper type Paper name Front panel name
Backlit Material HP Premium Vivid Color Backlit Film HP Prem Vivid Colr Bklit
Backlit material Backlit material
Backlit material (more ink) Backlit material (more ink)
Banner and Sign Material HP  Opaque Scrim HP Opaque Scrim
HP Durable Banner with DuPont  TyvekHP Durable Banner-Tyvek®
Indoor Banner Indoor Banner
Technical Paper HP Natural Tracing Paper HP Natural Tracing Paper
HP Translucent Bond Paper HP Translucent...

3.Remove the first end of the spindle from the righ
t-hand side of the printer, and then move the
spindle to the right in order to extract the other  end. Do not insert your fingers into the spindle
supports during th e removal process.
The spindle has a hub at each end to keep the roll  in position. Remove the blue hub at the left end
to mount a new roll. The hub slides along the  spindle to hold rolls of different widths.
4. Slide the lever-lock on the blue hub to the unlock
ed position and remove the...

6.Slide the spindle into the roll. Make sure that no
 space exists between the roll and the fixed hub at
the right end of the spindle.
Make sure that the paper will wind off the roll in  the correct direction. If it does not, remove the
spindle from the roll, turn the roll 180° and rest  it on the loading table. Then slide the spindle into
the roll.
NOTE: A label on the spindle also show s the correct winding direction.
7.Put the blue hub on to the uppe
r end of the spindle, and push it towards the end...

If you regularly use different paper types, you can change rolls more quickly if you pre-load rolls of
different paper types on different spindles. Extra spindles are available for purchase.
Load a roll into the printer
NOTE: To start this procedure, you need to  have a roll loaded on the spindle. See Load a roll onto
the spindle on page 33.
1.
At the printers front panel, select the  icon, and then select  Paper load > Load roll .
Alternatively, you can start loading paper withou t using the front...

6.If you have a take-up reel (a standard feature 
on the 1.5m printer and an optional accessory on
the 1.1m printer), a message will appear on the fr ont panel asking if you want to load paper onto
the take-up reel. If you select  No (or if you do not have a take-up reel) the front panel displays the
Ready  message and the printer is ready to print. If you select  Yes, a message will appear on the
front panel asking if you wa nt to load the take-up reel now or during printing.
●
If you want to load the...

The take-up reel is operated from the front panel.
Follow these guidelines when taping rolls to the take-up reel spindle core:
● Make sure that the paper is straight when it is 
attached to the spindle core. Otherwise it skews as
it winds onto the core.
● The spindle core on the take-up reel must be 
the same width as the paper that you are using.
● Check that neither side of the spindle core ha
s end caps, and make sure the spindle core is
pushed firmly into both spindle guides.
● If you are using a...

4.Unlock the take-up reel spindle by pushing 
the spindle lever to its uppermost position.
5.Remove the take-up reel spindle.
6.The front-panel display guides yo
u through the process of loading the take-up reel spindle core
onto the take-up reel spin dle. When that task is complete, lo ad the take-up reel spindle into the
printer by pushing firmly on both ends of the spindle.
ENWW Use the take-up reel
39
Handle the paper
 

7.Press the 
OK key on the front panel, and then select a winding direction.
The printer advances the paper. Make sure that th e paper passes in front of the loading table, as
shown.
8. Pull the paper taut to the position 
shown in the following figure. Do  not attempt to pull more paper
out of the printer. Use tape to  secure the paper to the spindle  core. You might need to use more
tape than is shown in the following image. The  paper should be secure enough to support the
weight of the loop-shaping...

9.Press the 
OK key on the front panel. The printer advances the paper.
NOTE: Make sure that you insert  the loop-shaping core. The ta ke-up reel will not function
correctly without it. The loop-shaping core must  have end caps. Make sure that the end caps
extend over the edges of the paper.
10. Assemble a loop-shaping core by
 matching the shape-coded and color-coded lengths of plastic
tubing. The loop-shaping  core must be the same width as the  paper that you are using. Make sure
that both end caps...

12.Carefully insert the loop-shaping core.
NOTE:
Make sure that you insert  the loop-shaping core. The ta ke-up reel will not function
correctly without it. The loop-shaping core must  have end caps. Make sure that the end caps
extend over the edges of the paper.
13. Use the wind-direction switch on the take-up reel  motor to select the winding direction. Setting 1
winds the paper so that the printed image faces in. Setting  2 winds the paper so that the printed
image faces out.
The front panel shows you...