HP Designjet T620 610 mm User Manual

3.Select  Paper load .
4.Select  Load roll .
5.Select your paper category and type.
TIP: If you have loaded a paper type whose name does not appear in the paper list, see The
paper type is not in the driver on page 114.
6. Continue with step five of the easy loading process, skipping steps eight and nine.
TIP: When prints fall into the basket, they can be torn or get ink marks from other prints. To avoid this,
catch your prints as they are cut from the roll and do not stack prints in the basket. You can...

Unload a roll
Before unloading a roll, check whether there is paper on the roll or if the roll is out of paper, and follow
the appropriate procedure as described below.
Unload paper key procedure with paper on the roll
If there is paper on the roll, use the following procedure.
1.Press the  Unload paper  key 
 on the front panel.
2. When prompted by the front-panel display, lift the blue lever on the left.
3. When prompted by the front-panel display, lightly rewind the paper from the end of the spindle...

Paper menu procedure with paper on the roll
If there is paper on the roll, you can also start the process from the paper menu in the front panels main
menu.
1.Press the  Menu key to return to the main menu, select the Paper menu icon 
.
2. Select  Unload paper .
3.Continue from step two of the  Unload paper key process.
Roll out of paper procedure
If the end of the paper is no longer attached to the roll use the following procedure.
1.If you have already started the unload process, press the  Cancel key...

Easy loading procedure
1.Standing in front of the printer, open the sheet tray.
2.Insert the sheet into the feeder. Load your sheet aligned with the load line and insert until the paper
will not continue, with thicker sheets you feel resistance. The printer detects the sheet in three
seconds. A countdown begins on the front-panel display.
WARNING! Do not push your fingers inside the printers paper path.
3.After the countdown, the paper feeds into the printer. Guide the sheet into the printer; this is...

6.The printer checks the alignment and measures the sheet.
NOTE: Depending on the length of the sheet, it feeds out the front of the printer.
7.If the paper has been loaded successfully, the front panel displays the  Ready message and the
printer ready to print. If the paper is not straight, follow the instructions on the front-panel display.
NOTE: When correctly loaded, the sheet is in the back of the printer.
NOTE:If you have an unexpected problem at any stage of the paper loading process, see The...

5.Select your paper category and type.
TIP: If you have loaded a paper type whose name does not appear in the paper list, see The
paper type is not in the driver on page 114.
6. Continue with step two of the easy loading procedure, skipping steps four and five.
Unload a single sheet
To unload a single sheet after printing, you can simply pull the sheet free from the front of the printer.
To unload a sheet without printing, use the  Unload paper key 
 or the paper menu procedure.
Unload paper key...

The following information is displayed on the front panel:
●Roll or sheet status
● Paper type you have selected
● Width of the paper in millimeters (estimated)
● Length of the sheet in millimeters (estimated)
● Color calibration status
● Paper advance calibration status
If no paper is loaded, the message Out of paper  is displayed.
The same information is displayed in the HP Printer Utility for Windows, on the Supplies page.
NOTE: Photo and coated paper requires careful handling, see The print is scuffed...

Maintain paper
To maintain paper quality, follow the recommendations below.
●Store rolls covered by another piece of paper or cloth
● Store cut sheets covered and clean or brush them before loading them in the printer
● Clean input and output platens and cut sheet tray
● Always keep the window of your printer closed
NOTE:
Photo and coated paper requires careful handling, see The print is scuffed or scratched
on page 128.
Change the drying time
You may wish to change the drying time setting to suit...

NOTE:The printer may not cut the paper directly after pressing the  Form feed and cut key , as
each time a print is printed the printheads are serviced and the paper cannot be cut until the process
completes.
Remove the cut piece from the output tray.
CAUTION: If strips or short prints are left in  the output tray the printer could jam.
NOTE:Photo and coated paper requires careful handling, see The print is scuffed or scratched
on page 128.
ENWW Feed and cut the paper 43
Paper handling
 

44 Chapter 5   Paper handlingENWW
Paper handling