HP Color LaserJet CM4730f User Manual

Menu itemSub-menu itemSub-menu itemValues and Description
  LAN HW TestCAUTIONRunning this embedded test will
erase your TCP/IP configuration.
This test performs an internal loopback test. An internal
loopback test will send and receive packets only on the
internal network hardware. There are no external
transmissions on your network.
Select Yes to choose this test, or No to not choose it.
  HTTP TestThis test checks operation of HTTP by retrieving
predefined pages from the device, and tests the
embedded...

Menu itemSub-menu itemSub-menu itemValues and Description
 Ping Test This test is used to check network communications.
This test sends link-level packets to a remote network
host, then waits for an appropriate response. To run a
ping test, set the following items:
Dest TypeSpecify whether the target device is an IPv4 or IPv6
node.
Dest IP4IPV4: Type the IPv4 address.
Dest IP6IPV6: Type the IPv6 address.
Packet SizeSpecify the size of each packet, in bytes, to be sent to
the remote host. The minimum is...

Menu itemSub-menu itemSub-menu itemValues and Description
 Ping Results Use this item to view the ping test status and results
using the control panel display. You can select the
following items:
Packets SentShows the number of packets (0 - 65535) sent to the
remote host since the most recent test was initiated or
completed.
Packets ReceivedShows the number of packets (0 - 65535) received from
the remote host since the most recent test was initiated
or completed.
Percent LostShows the percent of ping...

Menu itemSub-menu itemSub-menu itemValues and Description
100TX Auto: Limits auto-negotiation to a maximum link
speed of 100 Mbps.
1000TX Full: 1000 Mbps, full-duplex operation.
Print Protocols    Use this item to print a page that lists the configuration
of the following protocols: IPX/SPX, Novell NetWare,
AppleTalk, DLC/LLC.
Table 2-11  Jetdirect menus (continued)
38 Chapter 2   Control panelENWW
 

Fax Setup
Administration > Initial Setup > Fax Setup
Table 2-12  Fax Setup menu
Menu itemSub-menu itemSub-menu itemValuesDescription
Required SettingsCountry/Region (Countries/regions
listed)Configure the settings that are legally
required for outgoing faxes.
Date/Time  
Fax Header
InformationPhone Number
Company Name 
PC Fax Send  Disabled
Enabled (default)Use this feature to enable or disable PC Fax
Send. PC Fax Send enables users to send
faxes through the device from their
computers if they have the...

Menu itemSub-menu itemSub-menu itemValuesDescription
Fax Send Settings Fax Dial Volume Off
Low (default)
HighUse this feature to set the volume of the tones
that you hear while the device dials the fax
number.
Error Correction
Mode Enabled (default)
DisabledWhen Error Correction Mode is enabled and
an error occurs during fax transmission, the
device sends or receives the error portion
again.
JBIG Compression Enabled (default)
DisabledJBIG compression reduces fax-transmission
time, which can result in...

Menu itemSub-menu itemSub-menu itemValuesDescription
 Redial Interval The range is between
1 and 5 minutes. The
factory default is 5
minutes.Use this feature to specify the number of
minutes between dialing attempts if the
recipient number is busy or not answering.
Detect Dial Tone Enabled
Disabled (default)Use this feature to specify whether the device
should check for a dial tone before sending a
fax.
Dialing Prefix Off (default)
CustomUse this feature to specify a prefix number
that must be dialed...

E-mail Setup
Administration > Initial Setup > E-mail Setup
Use this menu to enable the e-mail feature and to configure basic e-mail settings.
NOTETo configure advanced e-mail settings, use the embedded Web server. For more
information, see 
Embedded Web server.
Table 2-13  E-mail Setup menu
Menu itemValuesDescription
Address ValidationOn (default)
OffThis option enables the device to check e-mail syntax when you type
an e-mail address. Valid e-mail addresses require the @ sign and
a ..
Find Send Gateways...

Device Behavior menu
Administration > Device Behavior
Table 2-15  Device Behavior menu
Menu itemSub-menu itemSub-menu itemValuesDescription
Language  Select the language
from the list.Select a different language for control-panel
messages. When you select a new language,
the keyboard layout might also change.
Key Press Sound  On (default)
OffUse this feature to specify whether you hear
a sound when you touch the screen or press
buttons on the control panel.
Inactivity Timeout  Type a value
between 10 and...

Menu itemSub-menu itemSub-menu itemValuesDescription
Tray BehaviorUse Requested Tray Exclusively (default)
FirstControl how the device handles jobs that
have specified a specific input tray.
Manually Feed
Prompt Always (default)
Unless LoadedSpecify how a prompt should appear when
the type or size for a job does not match the
specified tray and the device pulls from the
multipurpose tray instead.
PS Defer Media Enabled (default)
DisabledSelect either the PostScript (PS) or HP paper-
handling model.
Use...