HP Color LaserJet 4700dn User Manual

5.Insert the tray into the printer. The printer will display the tray’s media type and size. If the
configuration is not correct, press the 
 key when the printer prompts you to configure the tray for
type and size. (For more information see 
Configuring a tray when loading paper .)
6.If the configuration is correct, press  to clear the message.
Loading undetectable standard-sized media into Tray 2 and optional
trays
CAUTION If paper is loaded in Trays 3 through 6 when the printer is in sleep mode, the...

2.Adjust the rear media-length guide by squeezing the guide adjustment latch and sliding the back
of the tray to the length of the media being used.
3.Slide the media-width guides open to the size for the media you are using.
4.Load media into the tray face up.
NOTE For best performance, load the tray completely full without splitting or fanning the
ream of paper. Splitting or fanning the ream might cause a multi-feed problem, which could
result in a paper jam. The capacity of the paper tray can vary....

5.Insert the tray into the printer. The printer will display the tray’s media type and size. If the
configuration is not correct, press the 
 key when the printer prompts you to configure the tray for
type and size. (For more information, see 
Configuring a tray when loading paper .)
6.If the configuration is correct, press  to clear the message.
Loading custom-sized media in to Tray 2 and optional trays
To use custom media, you must change the size setting on the control panel to  CUSTOM and set the...

3.Load media into the tray face up.
NOTE For best performance, load the tray completely full without splitting or fanning the
ream of paper. Splitting or fanning the ream might cause a multi-feed problem, which could
result in a paper jam. The capacity of the paper tray can vary. For example, if you are using
75 g/m
2 (20 lb) paper, the tray holds a full ream of 500 sheets. If the media is heavier than
75 g/m2 (20 lb), the tray will not hold a full ream, and you must reduce the number of sheets...

Printing on special media
Use these guidelines when printing on special types of media.
NOTESpecial media such as envelopes, transparencies, custom-size paper, or heavy media
greater than 120 g/m2 is used in Tray 1.
To print on any special media, use the following procedure:
1. Load the media in the paper tray.
2. When the printer prompts you for the paper type, select the correct media type for the paper loaded
in the tray. For example, select  GLOSSY when loading HP Color Laser Glossy Photo Paper.
3....

Colored paper
●Colored paper should be of the same high quality as white xerographic paper.
● Pigments used in colored media must be able to withstand the printer’s fusing temperature of 190°
C (374°F) for 0.1 second without deterioration.
● The printer creates colors by printing patterns of dots, overlaying and varying their spacing to
produce various colors. Varying the shade or color of the paper will affect the shades of the printed
colors.
Envelopes
NOTE
Envelopes can be printed only from Tray 1....

Paper typePaper weight
Heavy and extra-heavy stock105-163 g/m2
28-43 lb
Cardstock164-220 g/m2
43-58 lb
Intermediate90-105 g/m2
24-28 lb
HP Tough paper5 mil
When printing on heavy paper types, use the following guidelines:
●Use Tray 1 for paper that is heavier than 120 g/m
2 (32 lb).
● For optimum results when printing on heavy paper, use the printer control panel to set the media
type for the tray to 
HEAVY.
● In either the software application or the driver, select 
Heavy as the media type, or print...

●Forms and letterhead should be sealed in a moisture-proof wrapping to prevent changes during
storage.
● Before loading preprinted paper such as forms and letterhead, verify that the ink on the paper is
dry. During the fusing process, wet ink can come off of preprinted paper.
● To load pre-printed forms and letterhead into Tray 1, load them face down with the top edge of the
page facing toward you.
● To load pre-printed forms and letterhead into Tray 2 or an optional tray, load them face up with the
top...

Using features in the printer driver
When you print from a software program, many of the product features are available from the printer
driver. For complete information about the features that are available in the printer driver, see the printer-
driver Help. The following features are described in this section:
●
Creating and using quick sets
●
Creating and using watermarks
●
Resizing documents
●
Setting a custom paper size from the printer driver
●
Using different paper/covers
●
Printing a blank...

To use quick sets
1.Open the printer driver (see 
Gaining access to the printer drivers ).
2. Select the quick set that you want to use from the  Print Task Quick Sets drop-down list.
3. Click  OK. The product is now set to print according to the saved settings in the quick set.
NOTE To restore printer-driver default settings, select  Default Print Settings from the Print
Task Quick Sets  drop-down list.
Creating and using watermarks
A watermark is a notice, such as Confidential, that is printed in the...