Honeywell Vx9 Manual

4 - 9
Connect Cables
There are many cables available for the Thor VX9. This section deals with those cables that are a part of the installation pro-
cess, such as:
Various data and communication cables are available for the Thor VX9.
Connect Keyboard
The Thor VX9 has PS/2 connectors for the keyboard and mouse.
Connect the adapter cable to the PS/2 connectors on the Thor VX9.
Connect the Honeywell keyboard to the adapter cable.
The Thor VX9 has a D9 connector for the keyboard and mouse.
Connect the...

4 - 10
60 key Keyboard
Shown with adapter cable.
1. To adapter cable
2. To 95-key keyboard cable
3. To VX9 keyboard connector 

4 - 11
Connect Antenna
Several antenna configurations are available for the Thor VX9. Options include:
 single 802.11 external antenna
 dual 802.11 external antennas
802.11 Remote Mount Antenna (page 4-11)
WAN Remote Mount Antenna (page 4-13)
 external Bluetooth antenna
The VX8 has up to four antenna connectors.
 Generally, the two top antenna connectors are used for the 802.11 antennas.
 The two bottom connectors are used for the Bluetooth antenna and the remote WAN antenna.
The VX9 has up to three...

4 - 12
Components and Mounting Diagram
Typical Installation
Mounting Instruction
1. Attach and secure the mounting plate or bracket to the highest point on the safety cage, following these pre-
cautions:
 The mounting plate or bracket must be mounted so the antenna is not damaged while the vehicle or any of 
its parts are moving.
 The antenna mounting portion of the plate or bracket must be parallel to the floor. 
 If the Thor VX9 requires two antennas, they must be mounted at least 12 inches (304.8mm)...

4 - 13
2. Attach the female connector of the coaxial cable to the antenna connector on the vehicle mounted Thor VX9. 
3. Secure the antenna to the mounting bracket or plate. 
4. Connect the antenna cable to the whip antenna. 
5. Use cable ties to secure the coaxial cable to the vehicle as necessary. Make sure the cable is routed so it is 
not damaged by any moving parts of the vehicle. 
6. If the Thor VX9 is using dual 802.11 antennas (diversity option), repeat these steps for the second antenna.
WAN...

4 - 14
Connect Vehicle Power
The DC/ DC power supply is used to power the Thor VX9. A DC/DC power supply must be used with the Thor VX9 regard-
less of vehicle voltage.
Determining Power Supply Type
Three different types of power supplies have been used with the Thor VX9. Use the table below to determine the type 
of power supply and follow the relevant instructions for that power supply.
 
 Model Numbers Identifying Features
 9000311PWRSPLY, 9-60VDC, 60W
 9000313PWRSPLY, 50-150VDC, 60W
Shown With Lid...

4 - 15
DC/DC Power Supply (Lid with Screws on Side)
The instructions in this section are for the DC/DC power supply models with input and output connection blocks located 
under a removable lid which is secured by screws through the top of the lid:
 VX89311PWRSPLY – Power Supply, DC to DC, 9 to 60V, 60W
 VX89313PWRSPLY– Power Supply, DC to DC, 50 to 150V, 60W
For other styles of DC/DC power supplies, refer to Determining Power Supply Type (page 4-14) for information and 
installation instructions....

4 - 16
2. If the Thor VX9 is on, perform a shut down.
3. Connect the power cable to the Thor VX9.
4. Route the cable from the Thor VX9 to the DC/DC power supply.  Route the power cable the shortest way pos-
sible.  The cable is rated for a maximum temperature of 105°C (221°F).  When routing this cable, it should be 
protected from physical damage and from surfaces that might exceed this temperature.  Do not expose the 
cable to chemicals or oil that may cause the wiring insulation to deteriorate.  Always...

4 - 17
17.  If used, connect the wiring from the vehicle to the screen blanking box.
18. Use proper electrical and mechanical fastening means for terminating the cable.  Properly sized “crimp” type 
electrical terminals are an accepted method of termination.  Select electrical connectors sized for use with 
18AWG (1mm
2) conductors.
19. Provide mechanical support for the cable by securing it to the vehicle structure at approximately one foot inter-
vals, taking care not to over tighten and pinch...

4 - 18
With Screen Blanking Box
It is assumed that the motion sensing circuitry in the illustration below is powered by internal vehicle circuitry 
and is any 12-60/72VDC signal triggered by vehicle motion (see blanking box label for allowable range).
ThorVX8
Vehicle
Mounted
Computer
Circular
Power
Connector -Vi
-Vo +Vo5
6
1
3
-Vi-Vo
+Vo
+ViGND
10A slowfuse
Close to power
source
Cable Shield Existing Circuitry onVehicle
Forklift Battery
Main Switch
Green
Yellow
Brown
White
DC/DC
Power
Supply
MOTION...