Honeywell touchscreen Keypad 6270 User Manual

Advanced System Features (Contd) 
41 
 
SCREEN ACTION 
 3.  Press the 
CONSOLE MODE  button on 
the More Choices screen.  The Keypad 
screen is displayed. 
  4.  Perform functions as you would from a 
regular alpha keypad.  

 
42 
 
Voice Messages  
Introduction to Recording and Retrieving Messages 
The 6270 provides the capability of recording voices messages for 
others on the premises. The number of messages is not limited 
however; the total time of all messages added together cannot exceed 
127 seconds. 
Note: The voice messages are stored in the memory of the 6270.  All 
messages will be lost  if the 6270 loses power or if it is reset. 
Voice messages are recorded and retrieved using the  “Message 
Center ” screen. The...

Voice Messages (Contd) 
43 
 
SCREEN ACTION 
 
  2.  Press the 
Record button and record 
your message.  As you are recording your 
message, the remaining time counter 
counts down to indicate the total 
remaining time available and a  “Recording 
New Memo …” message is displayed 
above the message list window. 
3.  Press the  Stop button when you are 
done recording the message.  The 
message indicator will be flashing and the 
message will be listed in the message list 
window. 
4.  To record...

Voice Messages (Contd) 
44 
 
SCREEN ACTION 
 
 
 
  2.  Select the message you wish to listen 
to by touching it in the message list and 
then pressing the 
Play Message button.  
As the message is being played, a  “Play 
(x): Voice Message …” message is 
displayed above the message list window. 
When the end of the message is reached, 
the playback will stop. 
3.  To listen to the next message, press 
the  Advance One Message and Play  
button. 
4.  If you wish to delete messages, press 
the  Delete...

 
45 
 
Summary of Audible Notific ation  
SOUND CAUSE  DISPLAY 
Loud, Interrupted* 
Keypad & 
External  Fire Alarm  FIRE
 is displayed; descriptor of 
zone in alarm is displayed. 
Loud, Continuous* 
Keypad & 
External  Burglary/Audible 
Emergency Alarm  
ALARM is displayed; descriptor of 
zone in alarm is also displayed. 
One Short Beep 
(not repeated) 
Keypad only a.  System disarm   
b.  System arming 
attempt with an 
open zone. 
c.  Bypass verify   a.  DISARMED/READY TO ARM is 
displayed.  
b.  The...

Summary of Audibl e Notificati on (C ontd) 
46 
 
SOUND CAUSE  DISPLAY 
Rapid Beeping  
Keypad only  a.  Trouble   
b.  AC power loss 
alert 
c.  Memory of 
alarm   a.  CHECK
 displayed.  Descriptor 
of troubled protection zone is 
displayed. 
b.  AC LOSS  displayed (may 
alternate with other displays that 
may be present). 
c.  FIRE or ALARM is displayed; 
descriptor of zone in alarm is 
displayed.  
Slow Beeping  
Keypad only  a.  Entry delay 
warning**  
b.  Exit delay 
warning (if 
programmed)  a....

 
47 
 
Summary of 6270 LED Oper ation 
6270 LED Operation 
The 6270 has three LEDs labeled - ARMED, READY and MESSAGE. 
MESSAGE LED is yellow, ARMED LED is red, and READY LED is 
green. Each LEDs on and off state has different meanings as 
described below.  
LED DESCRIPTION 
ARMED ON – Security system is armed. 
OFF  – Security system is not armed. 
READY ON  – Security system is disarmed and ready to arm. 
OFF  – Security system is armed or disarmed but not ready. If 
disarmed, faults or troubles are...

 
48 
 
6270 Setup  
How to Access 6270 Setup Options 
Setup allows you to adjust the touch screen contrast and/or adjust the 
6270 speaker volume.  You may also select the time interval that 
must pass prior to the 6270 going into screen saver mode (screen goes 
blank). Additionally, you may enter the  User Setup screen, 
Advanced Setup  screen (if enabled by your system installer), or 
Clean Screen  (maintenance mode) from the Setup screen by 
pressing the corresponding button. 
 
The  “Advanced Setup...

6270 Setup (Contd) 
49 
 
SCREEN ACTION 
 
 3.  Press the 
SETUP button on the More 
Choices screen.  The Setup screen is 
displayed. 
  

6270 Setup (cont d) 
50 
 
How to Adjust the Touch Screen Contrast 
You may adjust the touch screen contrast as follows: 
If…  Then … 
you want to increase contrast  move the slide bar above the current 
contrast setting. 
you want to decrease contrast  move the slide bar below the current contrast setting. 
another adjustment or selection is 
to be made go to the corresponding paragraph in 
this section. 
no additional adjustment or 
selection is to be made press the Back button below the 
screen to...