Honeywell touchscreen Keypad 6270 User Manual

System Overvie w (Contd) 
11 
 
Entry/Exit Delays 
Your system has preset time delays, referred to as exit delay and 
entry delay. Whenever you arm your system, exit delay gives you 
time to leave through the designated exit door without setting off an 
alarm. Exit delay begins immediately after entering any arming 
command, and applies to all modes of arming protection. If 
programmed, a slow beeping will sound throughout the exit delay 
period. 
Entry delay gives you time to disarm the system when you...

System Overvie w (contd) 
12 
 
User Codes 
Each user must be assigned a name with a corresponding 4-digit user 
code in order to gain access to various features and functions. Users 
for the system are programmed in a central user setup location that 
provides the specific questions for authorization level, partition 
assignment, and RF button assignment. 
Extended Functionality 
Extended functions are advanced functions that can be accessed 
through a standard alpha keypad or through emulation mode on...

 
13 
 
Security System Operation  
Introduction to Security System Operation 
You can arm your system in one of three arming modes: Away, Stay, 
and Night.  The following table lists the three different arming modes 
and the results of each. 
FEATURES FOR EACH ARMING MODE 
Arming 
Mode  Exit 
Delay  Entry 
Delay  Perimeter 
Armed  Interior 
Armed 
Away Yes Yes  Yes  Yes 
Stay Yes Yes  Yes  No 
Night*  Yes  Yes (set for Away or  Stay Mode) 
No (set for Instant or  Maximum Mode)  Yes   Yes (set for Away...

Security Sy stem  Operat ion (contd) 
14 
 
SCREEN ACTION 
 
       Arming (typical) 
 
       Armed (typical)  2.  On the Arming screen, press the 
selected arming button.   
o The 6270 beeps twice (Away 
and Night Maximum Modes) or 3 
times (Stay and Night Instant Modes) 
o  a 
DISARM  button appears 
o  a text message appears stating 
which zones are arming and whether 
or not there is an exit delay 
o  the screen changes to display 
the remaining exit delay time, and 
o  an open lock appears next to...

Security Sy stem  Operat ion (Contd) 
15 
 
How to Arm Multiple Partitions 
To arm multiple partitions: 
SCREEN ACTION 
 1.  From the Home screen press the 
SECURITY
 button to display the Arming 
screen. 
 
  2.  Make certain the Multi-Partitions button 
is checked. 
 
3.  Press the appropriate arming mode 
button. 
 
  4.  When prompted, enter the user code 
authorized to access other partition(s).    

Security Sy stem  Operat ion (contd) 
16 
 
SCREEN ACTION 
 If the user code is accepted, the system 
displays the partitions that the user has 
access to.   
Note:
 A user may have access to some 
(but not all) of the available partitions! 
You have two arming options: 
To arm one or more partitions, highlight 
the partition(s) to be armed by touching it 
on the screen, then press  ARM 
SELECTED . 
Press  ARM ALL  to arm all available 
partitions. 
  

Security Sy stem  Operat ion (Contd) 
17 
 
 How to Bypass Zones 
The Bypass function is used when you want to arm your system with 
one or more zones left open. Bypassed zones are unprotected and will 
not cause an alarm when violated while your system is armed.  
 
x  The system will not allow you to bypass fire or emergency zones. 
x   To bypass zones, the system must be disarmed first.
 
To bypass zones do the following: 
SCREEN ACTION  
  1.  From the Home screen, press the 
SECURITY
 button.  The...

Security Sy stem  Operat ion (contd) 
18 
 
SCREEN ACTION  
 
 3.  Press the 
SHOW ZONES  button on 
the More Choices screen. 
While the 6270 is requesting and 
receiving the zone data from the control 
panel, the screen displays  Please Wait!. 
Then the zones, along with their current 
status, are displayed. 
 
  4.  Highlight the zone(s) to be bypassed 
by touching it on the screen when the 
zones are displayed. 
 
 
5.  Press the 
BYPASS SELECTED  
button.  The User Authorization screen 
is displayed...

Security Sy stem  Operat ion (Contd) 
19 
 
SCREEN ACTION  
 6.  Enter your 4-digit user code.  The 
More Choices screen is displayed 
showing the system status as 
Ready-
Bypass   
 
 
  7. Press the 
BACK button to return to the 
“ Arming ” screen. 
  

Security Sy stem  Operat ion (contd) 
20 
 
How to Remove Bypassed Zones 
A bypassed zone will automatically be unbypassed when you disarm 
the system.  If the system is disarmed and a zone is bypassed, you 
can remove the bypass as follows: 
SCREEN ACTION  
 
 1.  View bypassed zones by pressing the 
SHOW ZONES
 button.  
While the 6270 is requesting and 
receiving the zone data from the control 
panel, the screen displays  Please Wait!. 
Then the zones, along with their current 
status, are displayed....