Honeywell Gen 4 User Manual

							
How to Change  User Codes User  Guide 
Changing  Codes Using User 1 
You should  change  your code  regularly  to prevent  potential  intruders from knowing  your code.  All 
codes  are 4-digits. 
The factory  set code is [0][1][2][3].  User code  I can  only be changed by user 1. 
To change  user code: 

LCD Keypad: o then  [0][1][2][3] 

Press 
0 and  then  enter  your code  [0][1][2][3]. The iil I 

LED goes off to indicate  that you  are in Programming lo>walk Test 

mode.  The first  menu Walk Test appears  on the  screen. 

Press 
[8] on  the  keypad  to enter  User Set-Up. 
8>Set Up 

User [Number]Press [1] or [2] on the  keypad  to edit  the required  user. 
[1] or [2] 
Enter  the new  [ 4-digit  code]. 
Ifthe code  is accepted  the 

system  produces  a double  beep. 
Ifit is  rejected  the code 

may already be in use  and  the system  produce  a long  tone. 

You  must  choose  a different  4-digit code. 

[
4-digit code] I 
Upon the last  keypress  the code is saved. ICode Saved 
I Press ® twice  to exit  Programming  mode. The iil ® 
LED comes on and  the screen  displays  the date and time. 
I Sunday 01-Jan 
14:10I. 
LED Keypad: o then  [0][1][2][3] 

Press  0 and  then  enter  your code  [0][1][2][3]. The./ 

LED  comes  on and  the iil LED  goes off to indicate  that you 

are  in Programming  mode. 12345678 ©©©©©©©© --"'~--©sos (J @ 

@..... I ©IilPress [8] on the keypad.  LEDs 1 and  2 are on to indicate 
[y]
that  you have  two options,  user I and  user  2. 
12345678 @@©©©©©© (J @--'_--@$O$Press  [1] or [2] on the  keypad  to edit  the required  user. @..... LEDs 1-4 are on. ©Iil 
Enter  the new [4-digit  code]. Ifthe code  is accepted  the 
system  produces  a double  beep. 
If it is rejected  the code 
may  already 
be in use and the  system  produces  a long  tone. 
You 
must choose  a different  4-digit code. 
Upon  the last  keypress  the code  is saved.  LEDs 1-4 are off. 
Press 
® twice  to exit  Programming  mode. Theiil LED 
comes  on 
and the ./ goes off. 10 
[1] or [2] then [4-digit  code] 
I  
						

							
c-------------­How to Change  User Codes  (contd) i User Guide 
Changing  Codes using User 2 
Your alann system  can have  a second  user code.  You may  find it useful  to set  up user  code  2 for  use  by 
a  neighbour  for use  when  you are on holiday.  User code  2 operates  like user  code 
1, but it cannot  be 
used  to change 
or delete  user code 1. 
To change  user code  2: 
LCD Keypad: 
Press  CD and  then  enter  user 2 [4-digit  code]. The 
III LED goes offto indicate  that you are in Programming 
mode.  The first  menu  Walk Test appears  on the  screen. 
Press  [8] to edit  user  2. 
Enter  the 
new [4-digit  code]. If the code  is accepted  the 
system  produces  a double  beep. 
If it is  rejected  the code 
may  already  be in use  and  the system  produces  a long 
tone.  You must  choose  a different  4-digit code. 
Upon  the last  keypress  the code  is saved. 
Press  CD twice  to exit  Programming  mode. The 
III 
LED comes  on and  the screen  shows the date  and time. 
LED Keypad: 
Press  CD and then enter  user 2 [4-digit  code]. The ".".. 
LED comes  on and  the III LED  goes offto indicate  that you 
are in Programming  mode. 
Press  the [8] 
to edit  user  2. LEDs  1-4 are on. 
Enter  the new  [4-digit  code]. 
Ifthe code is accepted  the 
system  produces  a double  beep. 
Ifit is  rejected  the code 
may  already  be in use  and  the system  will produce  a flat  tone. 
You  must  choose  a different  4-digit code. 
Upon  the last  keypress  the code  is saved.  LEDs 1-4 are off. 
Press  CD twice  to exit  Programming  mode. The 
III LED 
comes  on and  the""'"  goes off. 
11 
CD then  [4-digit  code] 
I 
I.o>walk Test 
I~~~ Code 
I [4-digit code] I
ICode Saved 
I CD I Ol-JanISunday 
14:10 
CD then  [4-digit  code] 

						

							
How to Delete User Code  2 User Guide 
How to Delete  User Code  2 
You can delete the second  code to prevent  it being  used. User 1 or user 2 can  delete  user code  2. 
CD  then  [0][\][2][3] 
To delete  user code  2 using  user code  1 
IO>Walk Test 
I 
LCD Keypad: 
Press CD and then  enter  your code  [0][1][2][3].  The ~ 00 LED goes offto indicate  that you  are in Programming " mode.  The first  menu Walk Test appears on the screen. s>set UpI) I.User 1 Press [8] on the keypad  to enter  User Set-Up. 
Press  [2] to edit  user  code  2. 
I~~~~ Code 
IPress G to delete  user code  2. G I
ICode DeletedThe message Code Deleted is displayed  on the  screen. 
I Press ® twice  to exit  Programming  mode. The 00 LED ® comes  on and  the screen  displays  the date  and time. I 01-JanISunday 
14:10 
CD then  [0][11[2][3] LED Keypad: 1~-:::-l___@$OSPress  CD and  then  enter  your code  [0][1][2][3].  The 00 @@@@@@:@@ c ®  : @i)~ ;LED goes offto indicate  that you are in Programming @UI ! mode. 

Press  [8] on the  keypad  to enter  User Set-Up.  LEDs I 

and  2 are  on. 
11 I.i " Press  [2] to edit  user  code  2. LEDs  1-4 are on. 

Press 
G to  delete  user code  2. 

User  code  2 is  deleted.  LEDs 1-4 are off. 

Press 
® twice  to exit  Programming  mode. The 00 LED 

comes on and the .? LED goes off. 
12  
						

							
@m 
User Guide 
To delete  user code  2 using  user code  2 
LCD Keypad: 
Press CD and  then  enter  the user  2 [4-digit  code].  CD 
then  [4jdigit code] 
The 
til LED  goes offto indicate  that you  are in 
Programming  mode. The first  menu 
Walk Test appears on /o>walk Test 
the screen. 
Press  [8] on the  keypad 
to edit  user  code  2. 

Press 
8 to  delete  user code 2. 

The message Code Deleted  is displayed  on the  screen. 

Press 
® twice  to exit  Programming  mode. The til LED 

comes 
on and  the screen  displays  the date  and time. 
LED Keypad: 
Press  CD and  then  enter  the user  2 [4-digit  code]. The 
® I Sunday Ol-Jan 
. 14 :10I 
CD then  [4-digit  code] 
til LED goes off to indicate  that you  are in Programming 
mode. 
I Press  [8] on the keypad to edit  user  code  2. LEDs  1-4 are  [8] Ion. 12345678 @@@@@@@@ !J@--L>_--@SOS @.,.... 
Press 
8 to delete  user code  2. 
User  code 2 is  deleted.  LEDs 1-4 are  off. 
Press 
® twice  to exit  Programming  mode. The ril LED 
comes  on and the.? LED  goes off. 
13  
						

							
" 
Duress Code User Guide 
Duress  Code 
Your alarm  system  can have  a duress  code. The Duress  code is used in a hold-up  situation  where there 
is  pressure  to set  or unset  the system.  The Duress  code operates  like your  normal  code but in addition  it 
silently  ·sends a signal  to the  Alarm  Receiving  Centre. The operator  at the  ARC  may request  the Police 
to  attend  your premises. 
The  duress  code can only  set up,  edited  and deleted  by the  installer  while in 
Engineer  program mode. 
14  
						

							
I 
1 
How to View  the Event i~g-J User  Guide 
How to View  the Event  Log 
LCD Keypad: 
The event  log gives  a display of all the events  that have  taken  place.  The events  are arranged by date 
and  time.  Up to 250  events  can 
be stored in the memory.  When the log reaches  250 events  and another 
event  takes place,  the oldest  event drops  out. 
To  view  the event  log: 
Press 
eD and  then  enter  your code  [0][1][2][3]. Thew LED eDthen [0][1)[2][3]
goes offto indicate  that you are in Programming  mode. 

The first menu  Walk Test appears  on the  screen. I 

lo>walk Test 
Press  CD. I CD 
Choose  [1] for  Event Log in LCD  screen. I  . 
Event Log ~ 
1 LCD,  2 LED?____ ~.The last event  (250) appears  on LCD screen. 
To  go forward  through the event  log in sequence,  press 
G  . [ ] 

To go back  through the event  log in sequence,  press 00 . 

Press 
® twice  to leave the menu. 
Togo to a specific  event: 
PresseD. 
Key in the  Event  Number  you want  to see  (e.g.  150). 
Press 
Q) . The event  appears  on the  LCD  screen. 
Press 
Q) again  to see  further  details ofthe event. 
luser 4 Press ® twice to leave the menu  option. 
~ 
Cf 
!C>View 
Event Log ~ 
15 
2S0>ENG ACCESS 
08:44:03 17-Ma  
						

							
12345678 @@@@@@@@ (I @--_--@sos @ .... @1iJ 
User  Guide How to Test the Alarm System 
2 = LED Keypad: 
The LED  keypad  is limited  to show  the last  eight  set periods  with the eighth  being the oldest.  Zone, 
sos and../' LEOs are on, to show  zone in alann  . A flashing  LED indicates  the first  zone  in alann. 
00 indicates  the status ofthe  panel  at the  time of the alann. 
Press  CD and  then  enter  your code  [0][1][2][3].  The 
00 LED goes CD then [Q][I][2][3] offand the../' LED comes  on to indicate  that you  are in I Programming  mode. 

Press 
® to  enter  into Event  Log menu.  LEOs 1 and  2 are  on. 

Press 
[2] for  LED  keypad.  The first  zone  to activate  is indicated cr 

by  a flashing  LED. 

I 
Press [1 to 8] for the  desired  event or ® to go  through 

events 
in sequence. 

Press  CD twice  to leave 
the menu. 
How  to Test  Your  Alarm  system 
You should  check that your  alann  system  still works  correctly  by periodically  carrying out the alann 
system  tests described  here. 
How to Test  the Bell,  Strobe  and Internal  Sounder 
This function  tests the alann  function ofthe Bell,  Strobe  or Internal  Sounder.  Pressing the appropriate 

key. 

[1-3] toggle  the function  ON or OFF. Using  the ® also selects  the appropriate  alann function. 

Pressing  [0] turns  all alann  outputs  to OFF. 

Pressing 
(l) toggles  the selected alann output. 

Pressing  CD turns 
off all outputs  and leaves  the function. 

The  outputs  are: 

1 = Bell, 2 = Strobe,  3 = Sounder 

NOTE: To test  the Low  volume  sounder  enable option  3 only.  To test  for a high  volume  sounder 
enable  both options  2 and  3 together. 
16  
						

							
r-;::------------~-lI ~esting the Alarm System (contd) User Guide 
LCD Keypad: 
Press (P) and  then  enter  your code  [0][1][2][3].  The IilLED 
goes off to indicate  that you  are in Programming  mode. The 
first  menu, 
Walk Test appears  on the  screen. 
Press 
Gi0 for  menu Alarm Test. 
Press  [1] 
or (P) to enter into first  function ON or OFF. 
Press  the 
Gi0 or number  [2] or [3] for  the  other  functions. 
Press 
® to leave  the menu. 
LED keypad 
Press (P) and  then  enter  your code  [0][1][2][3]. The IilLED 
goes off and the .r LED  comes on to indicate  that you 
are  in Programming  mode. 
Press  II} for  menu 
Alarm Test. 
Press  [1] or 0  to toggle  first function 
ON or OFF. 
Press  number  [2] and  [3] for the  other  functions. 
Press 
® twice  to exit  Programming  mode. The Iil LED 
comes  on and  the .r LED goes  off. 
17 
(P) then [0][1)[2][3] I  . 
lo>walk Test 
Gi0 I 
11>Alarm Test 
I 
I 
[1] or0 I 
01:Bell 

OFF 

I Gi0 or I[Number] 
~trobe. 
I 
cp
!l>Alarm Test 
(P) then  [0][1)[2][3] 
_.__.---L.I~__-, 2345678 @@@~@@@lct!iG=-~~~I~ ~:i' 
[1] 
I  
						

							
How to do a Walk  Test User Guide 
How  to do  a Walk  Test 
Walk around  your property,  and in tum cause  each detector  to go  into  alann.  Also, open and close 
all  door  and windows  that are protected  by the  system.  For each  detector  (including  door or window 
sensor)  that is activated  the system  produces  a series 
of beeps,  and the associated  zone is indicated  on 
the  keypad. 
NOTE: 	Do not  test  any Personal  Attack, Fire or Tamper keys during  the Walk  Test since  these  are 
still  active  and will  cause  a full  alarm. 
If any ofthe tests  fail, or you  are unsure ofthe  correct  procedure,  contact your installer 
CD  then  [0][11[2][3] 
LCD  Keypad: 
Press CD and then  enter  your code  [0][l][2][3].  The 00 
LED goes off to indicate  that you  are in Programming  mode. 
The  first  menu 
Walk  Test appears  on the  screen. 
00r[0] 
Press  0 or [0]. Zones  1-8 have  a zero  (0) 
below  each TPnumber. 00 
IWhen a zone  is successfully  tested, number  1 replaces  the O. ® Zones are added to the  list as each  one is activated. I l0>wal.k Test 
Press ® to leave  the menu or 0  to restart  the Walk  Test. 
LED keypad 
Press CD and then  enter  your code  [0][1][2][3].  The 00 LED  CD 
then [0][1][2][3] 
goes off and the./' LED  comes  on to indicate  that you are 
in  Programming  mode, 
Walk Test. 12345678 @@@@@@@@ o@ --"~--@SO$ @.... Press 0 or [0].  Zones  1-8 are off. I @Ol 
o 
When  a zone  is sucsessfully  tested, the LED  is on. 

Zones  are added  to list  as each  one is activated. 

Press 
® to  leave  the menu or 0  to restart  the Walk  Test. 
18  
						

							
! How to Set Up tbe  Time & Date J User  Guide 
How to Set  up the  Time  and Date 
LCD Keypad: 
Press  CD and  then  enter  your code  [0][1][2][3].  The Iil 
LED goes off, indicating  that you are in Programming 
mode. 
The  first  menu 
Walk Test  appears  on the  screen. 
Press  [4] and  the 
Time and Date Screen  appears. 
The 
Time can  be modified in hours,  minutes  and seconds 
in the format  HH:MM:SS.  The number  keys on the 
keypad  0-9 are used  for this  function.  As each  digit 
is 
modified  the cursor  moves  to the  next  one.  When  the time 
is correct  press Q) to accept  the change  and move to the 
next  screen 
or to cancel  the change  press ® twice. 
The 
Date can  be changed in day, month,  year format 
DD-MM-
YY. The  number  keys on the  keypad  0-9 are used 
for  this function. 
As  each  digit 
is modified  the cursor  moves  to the  next  one. 
When  the date  is correct  press 
Q) to accept  the change  or to 
cancel  the change  press 
® twice. 
LED Keypad: 
CD then [0][1)[2)[3] 
I 
lo>walk Test 
I [4] 
Time and Date 

Time? 13:46:17 

I 
Q) 

Time and Date 

Date? 17-05-06 

Q) 
I 
14>set Up 
'rime and Date 
Ifrequired,  the time  and date  can be entered  as per  the  procedure  for the  LCD  keypad.  However  no 
information  will be indicated  on the  LED  keypad.  The only  indication  on the  LED  keypad  that you are 
in  menu  4, 
Set up Time and Date, is that LEDs 1 to 6 on  the  LED  Keypad  will be ON. 
19