Honeywell Gen 4 User Manual

--- -----
Honeywell 

ADE Gen4 
--------.----­
User Guide 
G4 ACCENTA@ 
@ 
I 
CD 00 0 0006 0®®0 0@@0 
----­
6-6 
T---,CD~0"0~0=-'------------------­0006 0®®0 6-6 0@@0 
Servicing Organisation  (Installer) name: _______________ 

Telephone  Number: 
______________________ 

Date  of Installation: 
______________________ 

AccountNumber: ______________________~ 
~-----~ -~---- -----~ ------;;----------~~-~-----:-~~-~~~.--~-~~--~-.::::------~--~-~ 
-_____ ::.--"'-___________ ~ -_______ ~ _...

Table ofContentsUser Guide 
·Contents 
 

FeaturesUser Guide I 	J 
Introduction 
This User  Guide  tells you how  to operate  your intruder  alann system. To simplify  this User  Guide  we 
have  assumed  that the alann  system  has been  installed 
by a professional  intruder alann system  installer 
(the  installer),  and that  the system  is operated  in a "typical"  way. Aspects 
ofyour  system  that are not 
"typical"  will be described 
by your  installer. 
NOTE: 	If you have  any questions  about your intruder  alann...

r-·_·_··_·_··_-_·__· .-.~-~.-.~ 
. 	How to Set  the  System User Guide 
How  to Set  the System 
When  you leave  your premises  you will  need  to set  (or tum on)  the intruder  alarm system. 

Before  setting the system  you should  ensure that the premises  have been  completely  vacated and that 

all  doors  and windows  are closed.  Ensure that pets  do not  have  access  to the  protected  areas 
as they 

can  cause  a false  alarm.  . 

NOTE:  The Accenta  Remote LED keypad  is not  shown....

--
How to Unset  the System User Guide 
How  to Unset  the System 
When  you enter  your premises  you need  to unset  (tum off) the system. 
LCD  Keypad: 
Sunday 01-JanEnter  the premises  by the  agreed  entry route.  The system 
produces  an entry  tone. The 
rJ LED  is on  and  the Iil LED  is 14:10 Ioff, indicating  that the system  is set. [ 4-digit code] 
Enter  your 4-digit  code (0 123  default). I 
** The  system  unsets with a double  beep. The Iil LED comes 
on,  indicating  that the system...

How to Part Set User Guide 
How  to Part  Set the System 
Ifyour  installer  has programmed  your system  for part set operation  you can set certain  zones of the 

system  while others  remain  unset. Part set operation  is often  used at night  time, and it permits  you to 

freely  walk around  the bedrooms  while the living  area and outside  doors are protected.  Your system 

may  have  2 part-set  programs  called Program  2 and  Program  3. 

Before  part-setting  the system  you should  ensure...

How to Silence an Alarm··~User Guide 
LED Keypad: 

The til LED should  be on. 

Enter  your code  [0][1][2][3].  The exit beep  starts. 
Press  the CD  key.  The exit tone  stops  and the zone  LEDs 
lto 3 
come  on. 
Select  part-set  program  [2] 
or [3]. The  system  sets after  a 
short  time.  The 
til LED goes out. 
NOTE: 	 There are no exit  beeps 
ifSilent  Timed  exit mode  has been 
programmed. 
©sos ©.-"I @1iI 
(6)~~(~~~ O'@::. 
[0][1][2][3]  then CD 
I 
I [2 or 3] 
I 
12345678...

How to Omit Zones 	User Guide 
LED Keypad: 
Enter your code  [0][1][2][3]. 
The 
alann stops,  and the Zone, -? or sos LEDs  come on to show  the 
[0][1][2][3] 
cause 
ofthe  alann. 
NOTE: 	 When 
2 or more LEDs  are on,  the flashing  indicator  shows the first 
alann,  and the steady  indicators  show the second  and subsequent 
alanns. 
@ill
I Press® . 	® 
If the  Zone, -? or®  LEDs  go out and the 00 LED comes 

on,  the system  has been  reset. 

If any ofthe LEDs  continue to flash  then the...

How to Quick  Set User Guide 
LED Keypad: 
Enter  your [4-digit  code] to start  the exit  procedure  (for 
more  information  see How  to 
Set  the  System). 
Press  8 and  the exit  beep  tone stops,  and all LEOs  for used 
zones  that can be omitted  come on. 
Press  the zone  [number]  to be  omitted.  The LED  now flashes  to 
show  the zone  as omitted. 
If a flat  reject  tone is heard,  then the 
zone  cannot  be omitted. 
Press 
Q) or  allow  the system  to set. 
How  to Quick  Set the  System...

O@ ©sos ©.... @Iil 
How to Set  Up Chime  Mode User Guide 
How to Set  Up Chime  Mode 
Chime is a low  security  facility for use  when  the system  is unset. It is  particularly  useful in a shop  to 
warn 
of customers  presence, or in a house  to warn  when  a back  door has been  opened. When  a Chime 
zone  detects  movement  the system  produces  a 
brief tw(}-tone  sound, and the Zone  LED comes  on. 
To set any  zone  to Chime. 
LCD  Keypad: 
The lil LED  is on,  indicating  that the system  is...