Honeywell control panel OMNI 408408EU User Manual

 
– 11 – 
System Operation (cont’d) 
When the System is Not Ready 
If the system is not ready to be armed, the READY LED is off and the 
display indicates which zone or zones are not ready.  
Determine which zone or zones are not ready, resolve the problem, 
and arm the system normally.  If the problem cannot be resolved, you 
may bypass the zone that is not ready.  Bypassing should only be done 
if the problem on the zone cannot be resolved, OR if you intentionally 
wish to leave the zone disarmed.  For...

– 12 – 
System Operation (cont’d) 
To Arm the System In Instant Mode and Stay Inside 
In INSTANT STAY mode, the perimeter portion of your burglar 
alarm system is armed, but the time delays are eliminated from your 
normal entry/exit door(s).  All interior protection is disarmed, so you 
are free to move around inside. 
Check to make sure the system is READY.  When it is ready, press: 
INSTANT followed by  
 
 STAY followed by your User Code. 
When the system has been armed successfully, the ARMED LED is...

 
– 13 – 
System Operation (cont’d) 
To Arm the System In Instant Mode 
In INSTANT mode, all alarm sensors, including doors that normally 
have a delay to allow you to disarm the system, will immediately 
report an alarm if activated.  Check to make sure the system is ready. 
When it is ready, press: 
 INSTANT followed by your User Code. 
When the system has been armed successfully, the ARMED LED is 
on, and the following is displayed: 
 
LCD Keypad: 
ON: INSTANT 
  
Fixed-Word Keypad: 
INSTANT 
 
 
To...

– 14 – 
System Operation (cont’d) 
NOTE: Bypassed zones are NOT protected when the system is armed.  
After the bypass command has been accepted, the keypad sounds one 
long beep, and the following is displayed: 
 
LCD Keypad: 
BYPASSED:    ZN1 
FRONT DOOR  
Fixed-Word Keypad: 
BYPASS 
zone number displayed 
 
To Unbypass a Zone 
Pressing the BYPASS button returns a bypassed zone to normal 
operation.  To unbypass a zone(s), repeat the bypass function as 
follows: 
BYPASS followed by your User Code† and...

 
– 15 – 
System Operation (cont’d) 
If no alarms have taken place, the ARMED LED goes off, and the 
display shows: 
LCD Keypad: 
SYSTEM READY 
  
Fixed-Word Keypad: 
READY LED lit 
 
 
If alarms occurred while the system was armed, or if a trouble 
condition exists, the display shows: 
 
LCD Keypad: 
ALM MEM  ZN1 
FRONT DOOR  
Fixed-Word Keypad: 
ARMED LED off 
READY LED blinks 
 
The keypad scrolls through the zone or zones that were in alarm. 
Burglary alarms sound a steady tone at the keypad(s), and...

– 16 – 
User Codes 
Adding/Changing a User Code 
Users can be added or changed directly at the keypad. Your system 
can have up to 6 different User Codes. 
To add or change a User Code, press the following: 
 Master User Code  User ID (1-6)   New User Code 
CODE        
NOTES: 
• User number 1 is a master user and can create or modify other 
users.
 
• 
User number 6 can be a duress code that will transmit a special 
duress code to the central station.
 
 
Deleting a User Code 
To delete a user, press...

 
– 17 – 
Paging Feature 
Your installer may have programmed your system to send messages 
with certain system conditions to your pager.  An explanation of those 
messages is provided below. 
Follow-Me Displays 
The display shown on your pager is ACCTEXXX where: 
ACCT is the 4-digit central station no. 2 account number. 
E is the event code. There are 4 event types: alarms, troubles, 
openings, and closings. These event codes are as follows: 
Openings = 0, Closings = 1, Alarm or Trouble = 9 
 
If...

– 18 – 
Paging Feature (cont’d) 
1.  Access pager number programming by pressing in sequence the 
[#], [5], and [8] keys.  An acknowledgement tone sounds to indicate 
pager number programming has been accessed. 
 
 
The [#], [5], [8] command is accessible only while the system is disarmed and the 
dialer, dialer delay, and bell are not active. 
LCD keypads will display the existing pager phone number.
 
 
2.  Enter your new pager phone number.  Your new pager phone 
number may consist of up to 16...

 
– 19 – 
Miscellaneous Commands 
Arm System (Maid Code) 
If you choose to have a code that cannot disarm the system, but can 
arm the system, have your installer program this feature.  If 
programmed, User Code No. 5 has system arming capability only, and 
you can issue this code to a temporary user so they can secure the 
premises when they leave. 
Send Help Conditions 
Your system can be programmed for three separate Send Help Alerts 
that send an emergency signal to your central station.  These three...

– 20 – 
Miscellaneous Commands (cont’d) 
Quick Forced Arm Yes  No  
If programmed by your installer, Quick Forced Arm allows you to arm 
the burglar portion of your alarm system in the Away mode, bypassing 
all zones that are not ready.  To enable Quick Force Arm: 
Press [#], [2]. 
 A valid User Code is still required to disarm the system. 
 
U
L The Quick Forced Arm feature is disabled on UL installations. 
Quick Exit        Yes        No   
If enabled, this feature allows the user to exit without...