Honeywell control panel OMNI 400600624848 User Manual

- 21 - 
 
Miscellaneous Commands (cont) 
OMNI-LCD or OMNI-LCD-US: Press and hold down the INSTANT /  and 
CODE /  keys at the same time for about two seconds. Press the 1 
key to toggle the display between: 
Backlight 120s time out …. and …. Backlight Always On 
Press the [✱] key to exit this Backlight menu. 
KEYPAD SOUNDER 
The sounder (or loudspeaker) housed inside the keypad emits (annunciates) sounds 
according to the condition of the security system. If you are using an OMNI-KP, 
OMNI-KP-US,...

- 22 - 
 
Using a Pager  
If so programmed, the system can send messages to a pager. The messages are 
displayed as follows: 
ACCT E XXX where: 
ACCT =  the 4-digit central station No. 1 account number set by your system 
installer. We suggest that you obtain the number from your system 
installer and record it here.
 ACCT = 
 E =  the event code. There are 4 event types: alarms, troubles, openings, and 
closings. These event codes are as follows: 
Openings = 0, Closings = 1, Alarm or Trouble = 9 
  XXX...

- 23 - 
 
Using a Pager (cont) 
 The [#], [5], [8] command is accessible only while the system is disarmed and the dialer, dialer 
delay, and bell are not active. 
In pager phone number programming mode, only the LCD keypad provides visual display of the 
numbers already programmed or numbers that are being changed.  The LED and fixed-word 
style keypads provide no visual keypad display of these numbers. 
2.  Enter your new pager phone number.  Your new pager phone number may 
consist of up to 16...

- 24 - 
 
Testing the System 
SYSTEM TEST 
It is recommended that you test your system once a week using the 
following procedure: 
NOTE:  If your system is monitored, contact your central station before you perform 
this test. 
1.   Arm your security system. 
2.   Wait until your exit time is over.  Then activate the system by opening a protected 
zone (for example:  a window or door). 
3.  Confirm that the alarm sounding device (bell or siren) sounds.  If your system is 
connected to a central station,...

- 25 - 
 
Recommendations On Smoke Detectors 
With regard to the number and placement of smoke/heat detectors, we subscribe to 
the recommendations contained in the National Fire Protection Association’s (NFPA) 
Standard #72 noted below. 
 
Early warning fire detection is best achieved by the installation of fire detection 
equipment in all rooms and areas of the household as follows:  A smoke detector 
installed outside of each separate sleeping area, in the immediate vicinity of the 
bedrooms and on...

- 26 - 
 
Emergency Evacuation 
 
2nd FLOOR
BACK
FRONT
floor_plan2-V0
BATH CLOSET
BEDROOM
BEDROOM
BEDROOM
1st FLOOR
BATH KITCHEN
BEDROOMBEDROOM
PORCH
BACK DOOR
 Establish and regularly practice a plan of escape in the 
event of fire. The following steps are recommended by the 
National Fire Protection Association: 
1.  Position your detector or your interior and/or exterior 
sounders so that they can be heard by all occupants. 
2.  Determine two means of escape from each room.  One 
path of escape should...

- 27 - 
 
Glossary 
AC/:  Small green power on-off light between the center buttons on the keypad.  When lit, the 
system is running on primary power; when not lit, the system is running off the backup battery. 
ALARM:  Sound from keypad or other horn/siren indicates a burglar alarm, fire alarm, or other 
condition you should be alerted to. 
ARMED/DISARMED:  These terms refer to the burglary portion of your security system. There are 
several levels of operation that allow you to protect part of your...

- 28 - 
 
Glossary (cont) 
EXIT DELAY:  The period of time allowed between arming the system and leaving through a designated 
exit/entry door before the system will register an alarm condition.  This is determined at the time of 
installation. 
INTERIOR ZONE:  An interior zone is a group of points that protect the interior of your premises.  You 
may want to arm the perimeter portion of your system while leaving the interior zones disarmed to 
allow you to open interior doors and pass interior motion...

- 29 - 
 
RADIO FREQUENCY EMISSIONS STATEMENTS 
FEDERAL COMMUNICATIONS COMMISSION (FCC) Part 15 
This device complies with part 15 of the FCC rules.  Operation is subject to the following two conditions:  (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 
INDUSTRY CANADA 
This Class B digital apparatus complies with Canadian ICES-003. 
Cet Appareil numérique de la classe B est conforme...

- 30 - 
 INDUSTRIE CANADA 
AVIS: L’étiquette d’Industrie Canada identifie le matériel homologué. Cette étiquette certifie que le matériel est conforme aux normes de protection, d’exploitation et de sécurité des réseaux de télécommunications, comme le prescrivent les documents concernant les exigences techniques relatives au matériel terminal. Le Ministère n’assure toutefois pas que le matériel fonctionnera à la satisfaction de l’utilisateur. 
Avant d’installer ce matériel, l’utilisateur doit s’assurer...