Home > Honeywell > Control panel > Honeywell control panel OMNI 400600624848 User Manual

Honeywell control panel OMNI 400600624848 User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Honeywell control panel OMNI 400600624848 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 178 Honeywell manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							- 21 - 
     
    Miscellaneous Commands (cont) 
    OMNI-LCD or OMNI-LCD-US: Press and hold down the INSTANT /  and 
    CODE /  keys at the same time for about two seconds. Press the 1 
    key to toggle the display between: 
    Backlight 120s time out …. and …. Backlight Always On 
    Press the [✱] key to exit this Backlight menu. 
    KEYPAD SOUNDER 
    The sounder (or loudspeaker) housed inside the keypad emits (annunciates) sounds 
    according to the condition of the security system. If you are using an OMNI-KP, 
    OMNI-KP-US, OMNI-LCD, or OMNI-LCD-US keypad, the sounds from the keypad 
    sounder can be controlled. 
    To change the keypad sounder: 
    OMNI-KP or OMNI-KP-US: Press the 
    BYPASS /  and CODE /  keys 
    at the same time and hold down for two seconds until you hear a beep. Press any 
    key (except the 
    T key) to toggle the sounder on or off. 
    0 = Sounder off      1 = Sounder on 
    Press the [✱] key to exit the sounder menu. 
    OMNI-LCD or OMNI-LCD-US: There are four modes available in the Sounder Menu.  
    They are as follows: 
    •  On – Normal Sounder Keys (all sounds on) 
    •  Key – Only Key Clicks 
    •  Fire – Only Fire Sounder (temporal sounder – not supported by all systems) 
    •  Off – No Sounds at all 
    To use the OMNI-LCD or OMNI-LCD-US sounder menu: 
    1. Press the 
    BYPASS /  and CODE /  keys at the same time and 
    hold down for two seconds. This accesses the Sounder Menu. 
    2. Press the 
    1 key to toggle through the four modes listed above (stop at 
    desired mode). 
    3. Press the 
    2 key to toggle through the sounder volume choices (high or low 
    appears on the display). 
    4. Press the 
    3 key to adjust the sound of the key acknowledge (Ack H or L 
    appears on the display). 
    5. Press the 
    T key to exit the Sounder Menu.  
    						
    							- 22 - 
     
    Using a Pager  
    If so programmed, the system can send messages to a pager. The messages are 
    displayed as follows: 
    ACCT E XXX where: 
    ACCT =  the 4-digit central station No. 1 account number set by your system 
    installer. We suggest that you obtain the number from your system 
    installer and record it here.
     ACCT = 
     E =  the event code. There are 4 event types: alarms, troubles, openings, and 
    closings. These event codes are as follows: 
    Openings = 0, Closings = 1, Alarm or Trouble = 9 
      XXX =  the zone* or user* designation, depending on the event. 
    * Possible Zone numbers are: 001–008 (OMNI400), 001–012 (OMNI600), 
    001–024 (OMNI624), 001–048 (OMNI848) 
    Possible User numbers are: 001–015 (OMNI400 and OMNI600), 001–032 
    (OMNI624), 001–064 (OMNI848) 
    Note that the following actions not requiring a user code are reported as: 
    •  Soft keys *&#, 1&3, and 7&9 send event number 9 and zone number of 124. 
    •  If the system is programmed by your installer for Stay Arms Stay, when the 
    system is armed by pressing the [STAY/
    ] key it will be reported to the pager as 
    user 001. 
    •  If the system is programmed by your installer for Instant Arms Away, when the 
    system is armed by pressing the [INSTANT/ 
    ] key it will be reported to the 
    pager as user 001. 
    •  If the system is armed with a keyswitch, programmable digits that were set up by 
    your installer will be sent to the pager as the user number. 
    •  When the system auto arms, it will be reported to the pager as user number 126. 
     If multiple events occur, only the signal for the highest-priority event is sent. Events ranked from 
    highest to lowest priority are alarm, trouble, open, and close. 
    CHANGING THE PAGER PHONE NUMBER (FOLLOW-ME) 
    You can change your pager follow-me phone number as follows if your installer 
    enabled this feature: 
    1.  Access pager number programming by pressing the following keys in sequence: 
    #, 5, and 8.  
    An acknowledgement tone sounds to indicate pager number programming has 
    been accessed.  
    						
    							- 23 - 
     
    Using a Pager (cont) 
     The [#], [5], [8] command is accessible only while the system is disarmed and the dialer, dialer 
    delay, and bell are not active. 
    In pager phone number programming mode, only the LCD keypad provides visual display of the 
    numbers already programmed or numbers that are being changed.  The LED and fixed-word 
    style keypads provide no visual keypad display of these numbers. 
    2.  Enter your new pager phone number.  Your new pager phone number may 
    consist of up to 16 characters (1-9, 0).  It may be necessary to add time to allow 
    the pager to answer before dialing your pager number.  To enter a 2-second 
    pause, press the 
    CODE / key.  (Entering a 2-second pause is optional 
    and is not required to enter your pager phone number.)  If the CODE/
     key 
    was pressed, it counts as one character.  The keypad will emit a single 
    acknowledgement chirp as each number is pressed. 
    3. Press the 
    # key after you have made your pager phone number changes. 
    Pressing the [#] key saves your new pager number and nulls out the remaining 
    locations.  An acknowledgement tone sounds. 
    To exit without saving changes, press the 
    T key to exit pager phone number 
    programming.  An acknowledgement tone sounds to indicate pager number 
    programming has been exited. 
     If you press the [✴] key without first pressing the [#] key to save your new pager phone number, 
    the system exits the pager phone number programming mode without saving the changes. 
    If no key is pressed within 10 seconds, the pager phone number programming mode times out 
    and exits automatically without saving any information entered. 
    TURN PAGER REPORTING ON/OFF FOR THE PARTITION (OMNI624 and 848 ONLY) 
    You can turn on/off the open-close reporting feature for a partition by pressing 
    #, 8.  The display prompts you to toggle the feature on/off with the 
    # key.  To exit, press the T key.  
    TURN PAGER REPORTING ON/OFF FOR A USER 
    You can turn on/off the open-close reporting feature for a user by entering the 
    following : 
    #, 7, [master code] [user number] [4] 
    NOTE:  The [#], [7] command is also used to assign a user to a different partition for 
    the OMNI624 and 848 only (see ASSIGNING PARTITIONS TO USERS on page 15).   
    						
    							- 24 - 
     
    Testing the System 
    SYSTEM TEST 
    It is recommended that you test your system once a week using the 
    following procedure: 
    NOTE:  If your system is monitored, contact your central station before you perform 
    this test. 
    1.   Arm your security system. 
    2.   Wait until your exit time is over.  Then activate the system by opening a protected 
    zone (for example:  a window or door). 
    3.  Confirm that the alarm sounding device (bell or siren) sounds.  If your system is 
    connected to a central station, the keypad will sound the ringback tone to confirm 
    that the signal was received. 
    4.   Disarm the security system. 
    5.  Call the central station to tell them you are finished testing. 
     
    BATTERY TEST 
    It is recommended that you test your battery once a month.  In order to test your 
    backup/standby battery, the following procedure should be followed: 
    1.  Disconnect AC Power from the system. 
    2.   Observe that the AC indicator light on the keypad goes off. 
    3.  Activate your alarm by performing the above SYSTEM TEST.  Remember to 
    contact your central station if your system is monitored. 
    4.   Reconnect AC Power to the system. 
    IMPORTANT: Use only batteries recommended by your installer as a replacement. 
    The National Fire Protection Association publishes a standard for fire warning 
    equipment (NFPA publication #72).  Further information can be obtained by 
    contacting: NFPA Public Affairs Dept., Batterymarch Park, Quincy, MA  02269. 
    If you have any further questions about the operation of your system, please contact 
    your alarm company.  
    						
    							- 25 - 
     
    Recommendations On Smoke Detectors 
    With regard to the number and placement of smoke/heat detectors, we subscribe to 
    the recommendations contained in the National Fire Protection Association’s (NFPA) 
    Standard #72 noted below. 
     
    Early warning fire detection is best achieved by the installation of fire detection 
    equipment in all rooms and areas of the household as follows:  A smoke detector 
    installed outside of each separate sleeping area, in the immediate vicinity of the 
    bedrooms and on each additional story of the family living unit, including basements 
    and excluding crawl spaces and unfinished attics. 
     
    In addition, the NFPA recommends that you install heat or smoke detectors in the 
    living room, dining room, bedroom(s), kitchen, hallway(s), attic, furnace room, utility 
    and storage rooms, basements, and attached garages. 
     
     
    DININGKITCHENBEDROOM
    BEDROOM
    BEDROOM
    BEDROOM
    LIVING ROOMBEDROOMBDRM
    BDRM DINING 
    LIVING ROOM TV ROOMKITCHEN
    BEDROOM
    BEDROOM TO
    BR
    LVNG RM
    BASEMENTKTCHN.CLOSED
    DOORGARAGE
    Smoke Detectors for Minimum Protection
    Smoke Detectors for Additional Protection
    Heat-Activated Detectors
    floor_plan-V0  
    						
    							- 26 - 
     
    Emergency Evacuation 
     
    2nd FLOOR
    BACK
    FRONT
    floor_plan2-V0
    BATH CLOSET
    BEDROOM
    BEDROOM
    BEDROOM
    1st FLOOR
    BATH KITCHEN
    BEDROOMBEDROOM
    PORCH
    BACK DOOR
     Establish and regularly practice a plan of escape in the 
    event of fire. The following steps are recommended by the 
    National Fire Protection Association: 
    1.  Position your detector or your interior and/or exterior 
    sounders so that they can be heard by all occupants. 
    2.  Determine two means of escape from each room.  One 
    path of escape should lead to the door that permits 
    normal exit from the building.  The other is an 
    alternative route, such as through a window, should your 
    normal escape path be unpassable.  Station an escape 
    ladder at such windows if there is a long drop to the 
    ground. 
    3.  Sketch a floor plan of the building.  Show windows, 
    doors, stairs, and rooftops that can be used to escape.  
    Indicate escape routes for each room.  Keep these routes 
    free from obstruction and post copies of the escape routes 
    in every room. 
    4.  Assure that all bedroom doors are shut while you are 
    asleep.  This will prevent deadly smoke from entering 
    while you escape. 
    5.  Try the door.  If the door is hot, check your alternate 
    escape route.  If the door is cool, open it cautiously.  Be 
    prepared to slam the door shut if smoke or heat rushes 
    in. 
    6.  When smoke is present, crawl on the ground.  Do not 
    walk upright, since smoke rises and may overcome you. 
    Clearer air is near the floor. 
    7.  Escape quickly; don’t panic. 
    8.  Establish a common meeting place outdoors, away from 
    your house, where everyone can meet and then take 
    steps to contact the authorities and account for those 
    missing.  Choose someone to assure that nobody returns 
    to the house — many die going back.  
       
    						
    							- 27 - 
     
    Glossary 
    AC/:  Small green power on-off light between the center buttons on the keypad.  When lit, the 
    system is running on primary power; when not lit, the system is running off the backup battery. 
    ALARM:  Sound from keypad or other horn/siren indicates a burglar alarm, fire alarm, or other 
    condition you should be alerted to. 
    ARMED/DISARMED:  These terms refer to the burglary portion of your security system. There are 
    several levels of operation that allow you to protect part of your premises while you remain inside. 
    Fire sensors and other emergency and environmental features are always active and ready (armed); 
    they are not affected in any way by arming or disarming the burglary portion of your security 
    system. See ARMED-INSTANT, ARMED-STAY, and STAY. 
    ARM-STAY:   A system setting that turns on the perimeter protection of the building but allows 
    movement throughout the interior.  
    ARMED INDICATOR:  Red light in the upper portion of the keypad labeled Armed/
    .  When lit, some 
    part of the burglar alarm system is armed; when not lit, the burglary portion of the system is 
    disarmed. 
    AWAY:  A system setting that protects the premises while it is unoccupied.  All burglary sensors are 
    active. 
    BURGLARY/FIRE:  The two major functions of a security system.  Fire protection is always armed and 
    cannot be disarmed.  The burglary sensors protect against unauthorized entry into your premises.  
    The burglary protection can be armed and disarmed, and programmed for special levels of access 
    and notification. 
    BYPASS FEATURE:  The Bypass feature allows you to exclude a selected zone or zones from the 
    burglar alarm protection.  
    BYPASS/
     BUTTON:  A button on the keypad used to activate the Bypass feature. 
    CENTRAL STATION:  The signal monitoring center contacted by your security system over the 
    telephone and/or other communication channels when alarms are activated, if your system is 
    programmed to communicate alarms off site.  The central station will follow their procedures and 
    your instructions for contacting the proper authorities when a signal is received.  
    CHIME FEATURE:  An optional feature that causes the keypad to chime for one second when selected 
    doors are opened when the burglary protection is disarmed.  Once programmed by your installer, 
    you can turn Chime on and off with [#] [6]. 
    DISARMED:  See ARMED/DISARMED. 
    DURESS:  Duress is a system feature that you may have programmed into your system.  If someone 
    forces you to disarm your system, entering the special Duress user code disarms the system and 
    sends a silent duress emergency signal to the central station so personnel there can respond 
    appropriately.  
    ENTRY DELAY:  The period of time allowed between opening a designated entry/exit door and 
    disarming the alarm system before the system registers an alarm condition.  This is determined at 
    the time of installation.  Your system supports two entry times, allowing you to have a different 
    length of time for different doors.  
    						
    							- 28 - 
     
    Glossary (cont) 
    EXIT DELAY:  The period of time allowed between arming the system and leaving through a designated 
    exit/entry door before the system will register an alarm condition.  This is determined at the time of 
    installation. 
    INTERIOR ZONE:  An interior zone is a group of points that protect the interior of your premises.  You 
    may want to arm the perimeter portion of your system while leaving the interior zones disarmed to 
    allow you to open interior doors and pass interior motion detectors without causing an alarm. 
    KEYPAD:  A keypad is your link into your system.  It displays alarm and trouble messages, shows 
    faulted zones, and allows you to arm/disarm the system using the buttons.  Your system will have 
    one or more keypads. 
    PANIC BUTTON:  A push button that allows you to signal the central station that you need immediate 
    assistance.  Your system has programmable Keypad Send Help Alerts that can also serve as Panic 
    buttons. 
    PERIMETER ZONE:  A perimeter zone is a group of points that protect the exterior of your premises.  
    Your outside doors and windows would be programmed as a perimeter zone. 
    SENSOR:  The actual alarm sensor, detector or device installed to detect an intrusion, fire, or 
    environmental problem.  Examples include: door contacts, window contacts, motion sensors, 
    glassbreak sensors, smoke detectors, rate-of-rise heat detectors, temperature sensors, flood/water 
    sensors, and carbon monoxide gas detectors. 
    SILENT CONDITION:  Most types of alarms and troubles alert you with the keypad sounder and the 
    sirens, horns, or speakers located in your premises. The intent is to advise you of the alarm or 
    trouble and allow you to respond promptly.  The audible sounds also let an intruder know that he 
    has been detected and will hopefully scare him away.  In some circumstances, an audible alarm 
    might put your life in danger.  For that reason, those alarms are programmed as silent conditions.  
    For an example, see DURESS.  
    SYSTEM:  Your security system is composed of three main parts:  1) the control panel, which functions 
    as the system brain and the link to the monitoring agency (central station); 2) the keypad(s), which 
    provide you with system status and allow you to input commands; 3) security sensors such as door 
    and window contacts, motion sensors, smoke detectors, and other sensors as required to detect 
    intrusion, fire, and other conditions for your premises. 
    USER CODE:  A user code is a 4- or 6-digit code that is required to operate the system.  The OMNI400 
    and OMNI600 supports up to 15 separate user codes, the OMNI624 supports up to 32 separate user 
    codes, and the OMNI848 supports up to 64 separate user codes.  The system supports one master 
    user who can add/delete other user codes.  Two of the user codes may be dedicated to special 
    functions as defined by your alarm company at the time of installation.  (See the User Code 
    Assignments in this manual.) 
    ZONE:  A zone is a collection of sensors with common characteristics grouped together for your 
    operating convenience.  
    						
    							- 29 - 
     
    RADIO FREQUENCY EMISSIONS STATEMENTS 
    FEDERAL COMMUNICATIONS COMMISSION (FCC) Part 15 
    This device complies with part 15 of the FCC rules.  Operation is subject to the following two conditions:  (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 
    INDUSTRY CANADA 
    This Class B digital apparatus complies with Canadian ICES-003. 
    Cet Appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. 
     
    TELEPHONE/MODEM INTERFACE STATEMENTS 
    FEDERAL COMMUNICATIONS COMMISSION (FCC) Part 68 
    This equipment complies with Part 68 of the FCC rules.  On the front cover of this equipment is a label that contains the FCC registration number and Ringer Equivalence Number (REN).  You must provide this information to the telephone company when requested. 
    This equipment uses the following USOC jack: RJ31X 
    This equipment may not be used on telephone-company-provided coin service.  Connection to party lines is subject to state tariffs.  This equipment is hearing-aid compatible. 
    INDUSTRY CANADA 
    NOTICE: The Industry Canada Label identifies certified equipment. This certification means that the equipment meets telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction. 
    Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations. 
    Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company to request the user to disconnect the equipment. 
    Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together, This precaution may be particularly important in rural areas. 
    Caution: Users should not attempt to make such connections themselves but should contact appropriate electric inspection authority, or electrician, as appropriate. 
    RINGER EQUIVALENCE NUMBER NOTICE 
    The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface.  The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.  
    						
    							- 30 - 
     INDUSTRIE CANADA 
    AVIS: L’étiquette d’Industrie Canada identifie le matériel homologué. Cette étiquette certifie que le matériel est conforme aux normes de protection, d’exploitation et de sécurité des réseaux de télécommunications, comme le prescrivent les documents concernant les exigences techniques relatives au matériel terminal. Le Ministère n’assure toutefois pas que le matériel fonctionnera à la satisfaction de l’utilisateur. 
    Avant d’installer ce matériel, l’utilisateur doit s’assurer qu’il est permis de le raccorder aux installations de l’enterprise locale de télécommunication. Le matériel doit également être installé en suivant une méthode acceptée da raccordement. L’abonné ne doit pas oublier qu’il est possible que la conformité aux conditions énoncées ci-dessus n’empêche pas la dégradation du service dans certaines situations. 
    Les réparations de matériel nomologué doivent être coordonnées par un représentant désigné par le fournisseur. L’entreprise de télécommunications peut demander à l’utilisateur da débrancher un appareil à la suite de réparations ou de modifications effectuées par l’utilisateur ou à cause de mauvais fonctionnement. 
    Pour sa propre protection, l’utilisateur doit s’assurer que tous les fils de mise à la terre de la source d’energie électrique, de lignes téléphoniques et des canalisations d’eau métalliques, s’il y en a, sont raccordés ensemble. Cette précaution est particulièrement importante dans les régions rurales. 
    Avertissement: L’utilisateur ne doit pas tenter de faire ces raccordements lui-même; il doit avoir racours à un service d’inspection des installations électriques, ou à un électricien, selon le cas. 
    AVIS: L’indice d’équivalence de la sonnerie (IES) assigné à chaque dispositif terminal indique le nombre maximal de terminaux qui peuvent être raccordés à une interface. La terminaison d’une interface téléphonique peut consister en une combinaison de quelques dispositifs, à la seule condition que la somme d’indices d’équivalence de la sonnerie de tous les dispositifs n’excède pas 5. 
     
    TELEPHONE OPERATIONAL PROBLEMS 
    In the event of telephone operational problems, disconnect the control by removing the plug from the RJ31X wall 
    jack. We recommend that your certified installer demonstrate disconnecting the phones on installation of the system. 
    Do not disconnect the phone connection inside the control/communicator. Doing so will result in the loss of your 
    phone lines. If the regular phone works correctly after the control/communicator has been disconnected from the 
    phone lines, the control/communicator has a problem and should be returned for repair. If upon disconnection of the 
    control/communicator, there is still a problem on the line, notify the telephone company that it has a problem and 
    request prompt repair service. The user may not under any circumstances (in or out of warranty) attempt any service 
    or repairs to the system. It must be returned to the factory or an authorized service agency for all repairs. 
    This control unit was manufactured under rigid quality standards and complies with all UL requirements for 
    its intended use. Maintenance is best performed by your installing company with trained service personnel. 
     
     0560 DECLARATION OF CONFORMITY 
    Application of Council Directives 98/482/EC, 89/336/EEC, 73/23/EEC 
    Standards to which conformity is declared: 
    ETS 300 001:1997  EN50081-1  EN 50130-4:1995  EN 60950:1998 
    Intended use:  Alarm system, analogue subscriber interface to PSTN 
    Restrictions: None  
    EMC environment:   RESIDENTIAL, COMMERCIAL AND LIGHT INDUSTRY 
    Manufacturer:  Honeywell International Inc. 
    Address:  165 Eileen Way, Syosset NY 11791, USA 
    Customer support:  Contact your local distributor   
    						
    All Honeywell manuals Comments (0)

    Related Manuals for Honeywell control panel OMNI 400600624848 User Manual