Honeywell control panel LYNXREN User Manual

– 31 – 
USER FUNCTIONS 
Scheduling User Interface  
 
To access the Scheduling User Interface enter:                         + FUNCTION  +  [64] 
  Master user code or  
 Installer Code 
 The following entries will be sequentially prompted to the user. Note that all inputs are checked for 
validity upon entry and all invalid entries are rejected. Hitting a [*] will allow the entries to be 
accepted and advance to the next field. Hitting a [#] will reject the entry and back up one field. Hitting 
the [#]...

– 32 – 
USER FUNCTIONS 
Scheduling User Interface 
 NOTE:  The keypad beeps twice for invalid data entries (e.g.: an hour greater than 12), and the entry will not be 
accepted. The keypad beeps once for valid entries and four times when a schedule event is programmed 
successfully. 
[x] = the value that was last stored in the memory.   
 x n 
Schedule number 
[x] = schedule number 1 to 8 
[*] = continue 
[#] = exit schedule programming 
mode 
 
 
 
 
 
 
Enter the 1-digit schedule number to be...

– 33 – 
USER FUNCTIONS 
Scheduling User Interface 
  
 b :   xx 
Begin Time (minute) 
[xx] = begin minute 0 to 59 
[*] = continue 
[#] = return to previous prompt 
  
 
xx : bd 
Begin Day 
[xx] = begin day 01 to 17 
[*] = continue 
[#] = return to previous prompt 
 
 •  If  the value programmed in the Event Identifier is “3”, 
“4”, or “5”, and the current entry is completed, the 
system will save all field data up to this field. The 
system will beep four times and go back to the first field 
(Schedule...

– 34 – 
 
 
USER FUNCTIONS 
Scheduling User Interface  
 
Event Identifier Entries 
 
Entry Event Comment 
0 Empty  No event scheduled (or schedule is temporarily disabled) 
 
1 X-10 Device  Turn an X-10 device, either on or off at begin/end times. (will 
have a start and end time to program) (time driven) 
NOTE: SH10A siren cannot be used. 
 
2 Latch Key Report  Send a special pager report (7110000) indicating system not 
yet disarmed. (will have a start/end time to send the report) 
(window driven),...

– 35 – 
USER FUNCTIONS 
Scheduling User Interface 
 
Day of Week Entries 
 
 
Entry  
Day 
00  Invalid day entry  
01  Do event on next time match on the next Monday (will remove itself after executing)  
02  Do event on next time match on the next Tuesday (will remove itself after executing)  
03  Do event on next time match on the next Wednesday (will remove itself after executing)  
04  Do event on next time match on the next Thursday (will remove itself after executing)  
05  Do event on next time...

– 36 – 
USER FUNCTIONS 
Remote Phone Control Feature 
 
The LYNXR-Series is equipped with a remote interactive phone capability that permits access to the 
security system from any off-site touch-tone telephone using all user codes. If this feature has been 
programmed, the system will provide the appropriate voice messages and any system beeping sounds 
indicating the status of the security system over the phone line. (Refer to Summary of Audible 
Notification for further information.) The following...

– 37 – 
USER FUNCTIONS 
Remote Phone Control Feature 
 
Enter:                        (within eight seconds) 
  Your user code 
Upon entering remote phone control mode the Lynx will announce “System, enter code”. 
Remote Phone Control Commands 
 
To remotely disarm system: 
                       + [1] 
  Your user code 
To remotely arm in AWAY mode:                        + [2] 
  Your user code 
To remotely arm in STAY mode:                        + [3] 
  Your user code 
To remotely arm in AWAY or...

– 38 – 
USER FUNCTIONS 
Speaker Phone Feature 
 
If this feature has been programmed the LYNXR-EN is capable of operating as a speaker phone. 
During speaker phone operation the system will provide the following functions: 
• All function/event processing will continue to operate, but there will be no announcements. 
• The ARMED (red) and READY (green) LEDs will alternately blink. 
• “PH” will be displayed. 
NOTE:  The system will enter the Speaker phone mode even if an alarm or trouble is stored in the...

– 39 – 
USER FUNCTIONS 
Speaker Phone Feature 
 
LYNXR-EN Speaker Phone Functions 
To place a call using the Speaker Phone:  
[#] + AUX and dial the desired phone number. 
To answer a call using the Speaker Phone: 
[#] + AUX  
To flash (switch between two calls using call waiting): 
AUX  
To hang up:  
OFF   
To activate/deactivate (toggle) ringer:  
[#] +  VOLUME  +  AUX  
To return the keypad to telephone mode after disarming the system: 
[#] + AUX  
NOTES:  (1)  The speaker phone ringer can only be...

– 40 – 
FIRE ALARM SYSTE
FIRE ALARM SYSTEFIRE ALARM SYSTE FIRE ALARM SYSTEM 
M M  M (If Installed)
(If Installed)(If Installed) (If Installed) 
    
General Information 
 
U
UU U
L
LL L 
    
 LYNXR-EN is not intended for UL985 Household Fire applications unless a 24-hour backup battery 
(P/N LYNXRCHKIT-HC) is installed. 
 
General  
Your fire alarm system (if installed) is active 24 hours a day, providing continuous protection. In the 
event of an emergency, the installed smoke and heat detectors will...