Honeywell control panel LYNXREN User Manual
Have a look at the manual Honeywell control panel LYNXREN User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 178 Honeywell manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
– 31 – USER FUNCTIONS Scheduling User Interface To access the Scheduling User Interface enter: + FUNCTION + [64] Master user code or Installer Code The following entries will be sequentially prompted to the user. Note that all inputs are checked for validity upon entry and all invalid entries are rejected. Hitting a [*] will allow the entries to be accepted and advance to the next field. Hitting a [#] will reject the entry and back up one field. Hitting the [#] in the “Schedule Number” screen will exit the schedule programming. NOTES: 1. During the schedule programming, if three minutes passes and no key was entered, the programming will be terminated and no values will be saved. Furthermore, if a zone is troubled while in schedule programming, the system will abort the programming mode and show the troubled zone, and any uncompleted program event will not be saved. 2. It is not possible to enter the schedule programming mode from a wireless keypad. 3. Pressing any key on a wireless (RF) keypad terminates Scheduling setup. 4. It is not possible to enter the schedule programming mode when either FC or CA is displayed on the display. Because the keypad display does not show prompt titles, you must refer to these instructions while programming the system. The prompts are indicated by a number/letter combination. The prompts for option #64 are as follows: n Schedule number------------- for selecting a schedule number (1-8) i d Event identifier--------------- for selecting a schedule action (0-5) : A b Begin time (hrs, am/pm)---- for selecting a schedule begin time (hour, am/pm) entry (00-12) b : Begin time (min)------------- for selecting a schedule begin time (minute) entry (00-59) b d Begin day--------------------- for selecting a schedule begin day (01-17) : A E End time (hrs, am/pm)------ for selecting a schedule end time (hour, am/pm) entry (00-12) E : End time (min)--------------- for selecting a schedule end time (minute) entry (00-59) E d End day------------------------ for selecting a schedule end day (01-17) d n Device number--------------- for selecting a X-10 device number (1-8)
– 32 – USER FUNCTIONS Scheduling User Interface NOTE: The keypad beeps twice for invalid data entries (e.g.: an hour greater than 12), and the entry will not be accepted. The keypad beeps once for valid entries and four times when a schedule event is programmed successfully. [x] = the value that was last stored in the memory. x n Schedule number [x] = schedule number 1 to 8 [*] = continue [#] = exit schedule programming mode Enter the 1-digit schedule number to be programmed, then press [*] to accept and advance to the next programming field: Event Identifier. • Press the [#] key in this entry will exit the schedule programming mode. The keypad will beep four times and exit. • Schedule number 7 and 8 are always random events that are meant to work only with X-10 devices. NOTE: This feature should be implemented when the user is trying to give the impression that a premises is “lived in”. The events will occur at random times (0-59 minutes) within the defined hour. x id Event Identifier [x] = event identifier 0 to 5 [*] = continue [#] = return to previous prompt 0 = Empty - no event scheduled (or schedule temporarily disabled. Keypad will beep four times and return to Schedule Number with the schedule number advanced. 1 = X-10 Device - the user is required to enter data up to and include the Device Number screen. Selection #1 is a time driven event that requires a begin and end time. 2 = Latch Key Report - the user is required to enter data up to and include the End Day screen. Selection #2 is a window driven event that requires a begin/end time. 3 = Automatic Stay Arming - the user is required to enter data up to and include the Begin Day screen. Selection #3 is a time driven event that requires a begin time to send a report. 4 = Reminder Announcements - the user is required to enter data up to and include the Begin Day screen. This is a reminder announcement. 5 = Alarm Clock - the user is required to enter the field values up to and include the Begin Day screen. This is a an alarm clock. NOTES: (1) See figure 1 for an explanation of each entry of the event identifier. (2) If “Follow me” reminder telephone number is programmed, the reminder announcement is also delivered to that number. xx : Ab Begin Time (hour) [xx] = begin hour 00 to 12 [*] = continue [#] = return to previous prompt Begin Time (am/pm) [0] = begin time, am (A) [1] = begin time, pm (P) [*] = continue [#] = return to previous prompt • The begin hour is a two-digit entry. To enter the hour 3, press “0” followed by “3”. • The begin hour “00” indicates this schedule does not have a begin time. • Press “0” to select AM or “1” to select PM. NOTE: When programming schedule number 7 and 8, do not program turn on/off to occur within the same 1-hour period. This will prevent this random feature from causing a reversal of the on/off times.
– 33 – USER FUNCTIONS Scheduling User Interface b : xx Begin Time (minute) [xx] = begin minute 0 to 59 [*] = continue [#] = return to previous prompt xx : bd Begin Day [xx] = begin day 01 to 17 [*] = continue [#] = return to previous prompt • If the value programmed in the Event Identifier is “3”, “4”, or “5”, and the current entry is completed, the system will save all field data up to this field. The system will beep four times and go back to the first field (Schedule Number) with the schedule number advanced. • If the value programmed in the Event Identifier is “1” or “2”, and the current entry is completed, the system will advanced to the next programming field - End Time (hour). NOTE: See figure 2 for the definition of begin day entries. xx : AE End Time (hour) [xx] = end hour 00 to 12 [*] = continue [#] = return to previous prompt End Time (am/pm) [0] = end time, am (A) [1] = end time, pm (P) [*] = continue [#] = return to previous prompt • The end hour is a two-digit entry. To enter the hour 3, press “0” followed by “3”. • The end hour “00” indicates this schedule does not have a end time. • Press “0” to select AM or “1” to select PM. E : xx End Time (minute) [xx] = end minute 0 to 59 [*] = continue [#] = return to previous prompt xx : Ed End Day [xx] = end day 01 to 17 [*] = continue [#] = return to previous prompt NOTE: See figure 2 for the definition of end day entries. • If the event identifier is set to “2” upon completion of this field, the current schedule data will be saved and the system will go back to the next schedule number. x : dn Device Number [xx] = device number 1 to 8 [*] = continue [#] = return to previous prompt [*] will accept and save the entire schedule event. The system will beep four times and go back to the beginning of the programming field (Schedule Number) with the schedule number advanced. If the current schedule number is 8, the system will wrap around and set the schedule number to 1. NOTE: For X-10 devices.
– 34 – USER FUNCTIONS Scheduling User Interface Event Identifier Entries Entry Event Comment 0 Empty No event scheduled (or schedule is temporarily disabled) 1 X-10 Device Turn an X-10 device, either on or off at begin/end times. (will have a start and end time to program) (time driven) NOTE: SH10A siren cannot be used. 2 Latch Key Report Send a special pager report (7110000) indicating system not yet disarmed. (will have a start/end time to send the report) (window driven), (reports only to pager) NOTE: Option *49 must be programmed to be 6 or higher. Make sure unit is armed prior to start of window time. In addition a secondary phone number must be programmed in Option *42. 3 Automatic Stay Arming Will arm the system automatically, and bypass any open zones, at a given time. It will send a report to the pager and central station, indicating system has been auto armed stay, plus all bypass reports. (will have only a start time to send the report) (time driven) NOTES: (1) Prior executing auto stay arming, force bypass will be executed - if option *23 was enabled. (2) If pager report is required, Option *49 must be programmed to be 6 or higher. 4 Reminder Announcements Will announce the message recorded by your installer. This will be repeated every minute until a key is depressed, or a button type zone does an arm or disarm. † NOTE: Make sure installer programmed the message at the time of installation. 5 Alarm Clock Will start a trouble tone (beep) on the speaker, which will continue until a key is depressed. † Figure 1.
– 35 – USER FUNCTIONS Scheduling User Interface Day of Week Entries Entry Day 00 Invalid day entry 01 Do event on next time match on the next Monday (will remove itself after executing) 02 Do event on next time match on the next Tuesday (will remove itself after executing) 03 Do event on next time match on the next Wednesday (will remove itself after executing) 04 Do event on next time match on the next Thursday (will remove itself after executing) 05 Do event on next time match on the next Friday (will remove itself after executing) 06 Do event on next time match on the next Saturday (will remove itself after executing) 07 Do event on next time match on the next Sunday (will remove itself after executing) 08 Do event on next time match every day (will run continuously, remains in schedule after executing) 09 Do event on next time match every weekday (will run continuously, remains in schedule after executing) 10 Do event on next time match every day of the weekend (will run continuously, remains in schedule after executing) 11 Do event on next time match on the next Monday (will run continuously, remains in schedule after executing) 12 Do event on next time match on the next Tuesday (will run continuously, remains in schedule after executing) 13 Do event on next time match on the next Wednesday (will run continuously, remains in schedule after executing) 14 Do event on next time match on the next Thursday (will run continuously, remains in schedule after executing) 15 Do event on next time match on the next Friday (will run continuously, remains in schedule after executing) 16 Do event on next time match on the next Saturday (will run continuously, remains in schedule after executing) 17 Do event on next time match on the next Sunday (will run continuously, remains in schedule after executing) Figure 2.
– 36 – USER FUNCTIONS Remote Phone Control Feature The LYNXR-Series is equipped with a remote interactive phone capability that permits access to the security system from any off-site touch-tone telephone using all user codes. If this feature has been programmed, the system will provide the appropriate voice messages and any system beeping sounds indicating the status of the security system over the phone line. (Refer to Summary of Audible Notification for further information.) The following functions can be performed from any remote touch- tone telephone: • Disarm the system. • Arm the system in STAY or AWAY mode. • Activate or deactivate X-10 devices. • Bypass zones. • Check system status. The remote access session will be aborted if: • A report must be sent. • Any local or wireless key entry (e.g. 5827), except [*], is made. • User Code is not entered within eight (8) seconds of call pickup (during the “system…..system announcement). • No keys are depressed for a period of 15 seconds and while no announcement has been made by the system. Any remote key entry will, however extend this timeout back to 15 seconds. It will not be possible to begin a remote access session if: • A report must be sent • The system is in any Test mode. • During real time clock setting. • During scheduling setup. • Panel is in shutdown mode (programmed by your installer). • Panel is in Macro learning mode. • Remote phone control feature has not been enabled by your installer. NOTE: If a remote phone session is not granted by the system, for any of the reasons identified above, a modem tone will be generated before the end of the session. Using Remote Phone Control Feature Dial the controls’s phone number. If no answering machine is present, the control will pick up between 1 and 14 rings, depending on the number programmed by your installer and will periodically announce “SYSTEM”. During a remote phone control session “PC” will be displayed on the control. Enter: (within eight seconds) Your user code The system status will be announced. Enter phone control commands as described on the next page: If an answering machine is on the premises, you need to dial the premises and hang up on the first ring. Wait at least five (5) seconds (but no more than 22 seconds) and dial the premises phone number again. The control will pick up and periodically announce “SYSTEM”. NOTE (1) All voice announcements on the phone line will also be announced on the local speaker, unless the system has been placed in the mute mode. (2) Entry/Exit beeps will be terminated if you enter the remote phone access mode.
– 37 – USER FUNCTIONS Remote Phone Control Feature Enter: (within eight seconds) Your user code Upon entering remote phone control mode the Lynx will announce “System, enter code”. Remote Phone Control Commands To remotely disarm system: + [1] Your user code To remotely arm in AWAY mode: + [2] Your user code To remotely arm in STAY mode: + [3] Your user code To remotely arm in AWAY or STAY mode with no delay: + [2] or [3] + [0] Your user code To remotely activate X-10 devices 1-6: [#] + [4] + device no. To remotely activate X-10 devices 7 & 8: + [#] + [4] + device no. Your user code To remotely deactivate X-10 devices 1-6: [#] + [7] + device no. To remotely deactivate X-10 devices 7 & 8: + [#] + [7] + device no. Your user code To remotely Bypass zones: + [6] + zone no. Your user code To remotely activate Forced Bypass: + [6] + [#] Your user code To remotely check system status: [✻] To end remote phone session: Hang Up or + [9] Your user code NOTES: (1) Check with your installer to see if the Forced Bypass mode has been enabled. (2) When bypassing zones, make sure a confirmation beep sounds for each zone that has been bypassed.
– 38 – USER FUNCTIONS Speaker Phone Feature If this feature has been programmed the LYNXR-EN is capable of operating as a speaker phone. During speaker phone operation the system will provide the following functions: • All function/event processing will continue to operate, but there will be no announcements. • The ARMED (red) and READY (green) LEDs will alternately blink. • “PH” will be displayed. NOTE: The system will enter the Speaker phone mode even if an alarm or trouble is stored in the system memory. Although “PH” may not appear, the LEDs will alternately blink indicating you are currently in the Speaker Phone mode. ! !! ! Do not use the speaker phone as the only telephone in your home since in some special cases the speaker phone is not functional. The system will not enter speaker phone mode and LYNXR-EN will not ring if: • The feature has not been programmed. • A report is being sent. • An audible alarm is present. • An announcement is being made or a recorded message is being played back. • A message is being recorded. • If the system is in test or sniffer mode. • AC power is not present The speaker phone will be aborted if: • A report must be sent. • An audible alarm or trouble has ocurred. • AC power is lost. Using the Speaker Phone Feature When the LYNXR-EN is operating in the speaker phone mode the system keypad functions as a telephone keypad and the only security keypad functions that will remain enabled are the panic keys and the speaker volume control. (refer to Volume Adjustment section) You may adjust the volume before entering speaker phone mode or after dialing the desired number. In the speaker phone mode, if a zone is violated and has triggered an entry/exit delay, the system will automatically change the keypad from telephone to security mode. This allows the user to disarm the system or take other appropriate actions in the security mode without interrupting the telephone session. To regain telephone keypad control (i.e.: to enter an account number or menu selection) you will need to reactivate the telephone keypad.
– 39 – USER FUNCTIONS Speaker Phone Feature LYNXR-EN Speaker Phone Functions To place a call using the Speaker Phone: [#] + AUX and dial the desired phone number. To answer a call using the Speaker Phone: [#] + AUX To flash (switch between two calls using call waiting): AUX To hang up: OFF To activate/deactivate (toggle) ringer: [#] + VOLUME + AUX To return the keypad to telephone mode after disarming the system: [#] + AUX NOTES: (1) The speaker phone ringer can only be enabled/disabled when the speaker phone mode is not active. The system will ring once to confirm the ringer is enabled. Entering [#] +VOLUME +AUX a second time will disable the ringer. No ring will confirm that the ringer is disabled. (2) The speaker phone ringer will not ring when an alarm, trouble or entry/exit delay are sounding. (3) The LYNXR-EN speaker phone does not provide a “hold” feature. NOTE If you are using pulse (rotary) dialing, make sure that LYNXR- EN has finished dialing the last digit you dialed, (listen to pulses) before dialing the next digit.
– 40 – FIRE ALARM SYSTE FIRE ALARM SYSTEFIRE ALARM SYSTE FIRE ALARM SYSTEM M M M (If Installed) (If Installed)(If Installed) (If Installed) General Information U UU U L LL L LYNXR-EN is not intended for UL985 Household Fire applications unless a 24-hour backup battery (P/N LYNXRCHKIT-HC) is installed. General Your fire alarm system (if installed) is active 24 hours a day, providing continuous protection. In the event of an emergency, the installed smoke and heat detectors will automatically activate your security system, triggering a loud, intermittent sound from the keypad. An intermittent sound will also be produced by optional exterior sounders, and interlaced with the voice descriptor, sounding every 15 seconds. A “FIRE” message will appear at your keypad and remain on until you silence and clear the alarm display. In Case of Fire 1. Should you become aware of a fire emergency before your detectors sense the problem, go to your nearest keypad and press the single panic key (or panic key pair) assigned as FIRE emergency (if programmed by the installer) and hold down for at least 2 seconds. The alarm will sound. 2. Evacuate all occupants from the premises. 3. If flames and/or smoke are present, leave the premises and notify your local Fire Department immediately. 4. If no flames or smoke are apparent, investigate the cause of the alarm. The zone number of the zone(s) in an alarm condition will appear at the keypad. Silencing a Fire Alarm 1. Silence the alarm by entering: + OFF key. Your user code To clear the alarm display, enter: + OFF key again. Your user code 2. If the keypad indicates a trouble condition after the second OFF sequence, check that smoke detectors are not responding to smoke- or heat-producing objects in their vicinity. Should this be the case, eliminate the source of heat or smoke. 3. If this does not remedy the problem, there may still be smoke in the detector. Clear it by fanning the detector for about 30 seconds. 4. When the problem has been corrected, clear the display by entering: + OFF key. Your user code