Honeywell 4 Channel Manual

Configuration
Rev 3.03 63 Document 900.0315
02/07
The factory default Port settings are:
NoteThe system restarts automatically after changing the port 
settings.
NoteDo NOT use the same port number for two different programs, 
otherwise, the DVR cannot be connected with a PC running RAS.
CautionWhen changing the port settings, you must change the port 
settings on the PC running RAS as well. Refer to the Remote 
Administration System (RAS) User Guide for details.
To save your changes and return to the...

Configuration
Rev 3.03 64 Document 900.0315
02/07
Figure 3-51 LAN (DHCP) Setup Screen
LAN — ADSL (PPPoE)
Select ADSL (PPPoE) from the Type box on the LAN Setup screen to set up the ADSL 
network.
NoteADSL and modem cannot be configured at the same time. If the 
DVR is networked via modem, the ADSL (PPPoE) will not be 
selected.
Figure 3-52 LAN (ADSL) Setup Screen
1. Highlight the box beside ID and then press to display a virtual keyboard. Enter 
the ID for an ADSL connection.
2. Highlight the box beside...

Configuration
Rev 3.03 65 Document 900.0315
02/07
NoteEntering the ID and Password and highlighting OK reads the 
current IP Address of the DVR configured by the ADSL network.
NoteIf the DVR is configured for DHCP or an ADSL network, the IP 
Address of the DVR might change whenever the unit is turned 
on.
Modem Setup
Use the Modem Setup screen to configure your modem.
Figure 3-53 Modem Setup Screen
The Use field displays the available modem type: External Modem.
1. Highlight the box beside Baud Rate of...

Configuration
Rev 3.03 66 Document 900.0315
02/07
DVRNS (DVR Name Service) Setup Screen
DVRNS allows the DVR to use dynamic IP addresses for remote connection. Use the 
DVRNS Setup screen to configure the DVRNS server and register the DVR to use DVR 
name service.
Figure 3-54 DVRNS Setup Screen
1. Highlight the box beside Use DVR Name Service and then press   to toggle 
between On and Off,
2. Highlight the box beside DVRNS Server and enter the IP address or domain 
name of the DVRNS server
NoteObtain...

Configuration
Rev 3.03 67 Document 900.0315
02/07
NoteWhen using the NAT device, refer to the NAT manufacturer’s 
instructions for the appropriate network settings.
5. Highlight the box beside DVR Name and then press   to name the DVR to be 
registered on the DVRNS server. A virtual keyboard allows you to enter the DVR 
name.
6. Selecting Check allows you to check whether or not the name you entered can be 
used.
NoteThe DVR name you entered should be checked by selecting 
Name Check; otherwise, the...

Configuration
Rev 3.03 68 Document 900.0315
02/07
Callback Center Setup by LAN Connections 
Highlight Callback Center (MENU ➤ Network ➤ Callback Center) and then press 
 . The Callback Center Setup screen displays.
Figure 3-55 Callback Center Setup Screen
1. Highlight the box beside IP Address and enter the IP address of the computer 
you want contacted during an event.
2. Highlight the box beside Retry and enter the number of times you would like the 
DVR to try contacting the computer. You can select...

Configuration
Rev 3.03 69 Document 900.0315
02/07
NoteAuthentication should be turned On and ID and Password 
should be entered when using the SMTP server requiring user 
authentication.
Callback Center Setup by Modem Connections 
Figure 3-56 Callback Center (Modem) Setup Screen
1. Highlight the box beside Pager Number and enter the telephone number of the 
pager. Enter the number as it must be dialed from your telephone system; for 
example, if you must dial 9 for an outside line, enter 9 before the...

Configuration
Rev 3.03 70 Document 900.0315
02/07
Password Setup Screen
An Administrator password is required to:
 Turn the system off
 Enter the setup screen
 Load default setups
 Clear all data
 Change system date and time 
 Change the Administrator password
A User password is required to:
 Enter playback, fast forward playback and fast backward playback modes from 
Live Monitoring mode.
 Enter the search menu screen in Live Monitoring mode.
Highlight Password in the Main Menu (MENU 
➤ Password) and...

Configuration
Rev 3.03 71 Document 900.0315
02/07
To change the password, highlight the box below Password, and then press  . A 
window displays asking you to enter the current password. If you enter the correct 
password, another window displays asking you to enter a new password using 
the camera buttons. After you press  , another screen displays asking you to 
confirm the new password.
NoteThe Admin and User passwords are composed of up to eight 
digits using the camera buttons. The default User...

Configuration
Rev 3.03 72 Document 900.0315
02/07
Figure 3-58 Config Menu 
Clip Copy
Use the Clip Copy screen to copy video to an internal CD-RW drive, or external USB 
hard disk drive, or USB flash drive. The copied clip images can be viewed on computers 
running Microsoft Windows 98, ME, 2000 or XP. Refer to Appendix A, USB Hard Disk 
Drive Preparation for information on preparing the external drive for back up.
Highlight Clip Copy (MENU 
➤ Config ➤ Clip Copy) and then press  . The Clip Copy 
screen...