Honeywell 1900ghd-2 User Manual

13 - 13
Granit 1980i/1981i Scanner Guaranteed Performance (200 lux)
FocusFull Range (FR)
SymbologyNear DistanceFar Distance
7.5 mil Code 39in.3.962.4
cm
10.0158.6
10 mil Code 39in.
3.982.1
cm
10.0208.6
20 mil Code 39in.
6.2165.8
cm
15.8421.2
40 mil Code 39in.
15371.7
cm
38.1944.1
55 mil Code 39in.
22.2461.2
cm
56.51171.4
100 mil Code 39in.
47.5more than 629.9
cm
120.7more than 1600.0
100% UPCin.
5.085.3
cm
12.7216.7
7.5 mil Data Matrixin.
3.926.9
cm
10.068.3
10 mil Data Matrixin.
3.935.8
cm
10.090.8
55...

13 - 14
Standard Connector Pinouts
Note: The following pin assignments are not compatible with Honeywell legacy products.  Use of a cable with improper pin 
assignments may lead to damage to the unit.  Use of any cables not provided by the manufacturer may result in damage 
not covered by your warranty. 
Keyboard Wedge
10 Pin RJ41 Modular Plug - connects to the base
Serial Output
10 Pin RJ41 Modular Plug - connects to the base 
RS485 Output
10 Pin RJ41 Modular Plug - connects to the base
Note: RS485...

13 - 15
USB
10 Pin Modular Plug - connects to the base
Required Safety Labels
1 Cable shield
2 Cable select
3 Supply ground
4
5
6
7 +5V power
8
9Data +
10 Data -
Xenon 1900/1910/1902/1912 Scanner
Compliance 
Label 
location Part 
Number, Serial 
Number and 
Revision 
Information
location
Illumination output
LASER LIGHT- DO NOT STARE INTO BEAM  CLASS 2 LASER PRODUCT. REGARDER DANS LE FAISCEAU.  APPAREIL À LASER DE CLASSE 2. MAX. 1mW:
630-680 nm 
except for deviations pursuant to Laser Notice No. 50, dated...

13 - 16
CCB01-010BT Base
Part Number,
Serial
Number and 
Revision 
Information 
location
Compliance 
Label 
locations 

13 - 17
Granit 1910i/1911i/1980i/1981i Scanner
Laser Label location
Illumination 
output
Part Number, Serial 
Number and Revision 
Information locationCompliance 
label location
LASER LIGHT- DO NOT STARE INTO BEAM  CLASS 2 LASER PRODUCT. REGARDER DANS LE FAISCEAU.  APPAREIL À LASER DE CLASSE 2. MAX. 1mW:
630-680 nm 
except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007.  IEC 60825-1:2007. Complies with 21 CFR 1040.10 and 1040.11 
èfÂ.“#Øè]Z%ŽIƒ\%fÂ.“#Ø9îMØO©fÂ.“G±PèRAYONNEMENT...

13 - 18
CCB02-100BT/CCB05-100BT Base
Compliance 
Label 
locations 

14 - 1
14
Maintenance and Troubleshooting
Repairs
Repairs and/or upgrades are not to be performed on this product.  These services are to be performed only by an authorized 
service center (see Customer Support on page 15-1).
Maintenance
Your device provides reliable and efficient operation with a minimum of care.  Although specific maintenance is not required, the 
following periodic checks ensure dependable operation:
Cleaning the Scanner
The scanner or base’s housing may be cleaned with a soft cloth...

14 - 2
Inspecting Cords and Connectors
Inspect the interface cable and connector for wear or other signs of damage.  A badly worn cable or damaged connector 
may interfere with scanner operation.  Contact your distributor for information about cable replacement.  Cable replacement 
instructions are on page 14-2.
Replacing Cables in Corded Scanners
The standard interface cable is attached to the scanner with an 10-pin modular connector.  When properly seated, the connec-
tor is held in the scanner’s...

14 - 3
4. Pull the connector out while maintaining pressure on the connector release clip.
5. Replace with the new cable.  
Insert the connector into the opening and press firmly.  The connector is keyed to go in only one way, and will click into 
place.
Changing a Xenon Scanner Battery
1. Use a Phillips head screwdriver to remove the screw from the end cap.
2. Remove the end cap and remove the battery from the handle.
3. Insert replacement battery.
4. Replace end cap and screw.
Changing a Granit Scanner...

14 - 4
Is the scanner having trouble reading your symbols?
If the scanner isn’t reading symbols well, check that the symbols:
 Aren’t smeared, rough, scratched, or exhibiting voids.
 Aren’t coated with frost or water droplets on the surface.
 Are enabled in the scanner or in the decoder to which the scanner connects.
Is the bar code displayed but not entered?
The bar code is displayed on the host device correctly, but you still have to press a key to enter it (the Enter/Return key or 
the Tab key, for...