Honeywell 1250g2 Manual

3 - 5
To change the number of error beeps, scan the bar code below and then 
scan a digit (1-9) bar code and the Save bar code on the Programming 
Chart inside the back cover of this manual.  Default = 1.
Number of Error Beeps/LED Flashes 

3 - 6
LED Indicators
The green and red LEDs can be programmed to be On or Off and at different 
brightness levels to indicate various scanner states.  Use the following bar 
codes to program the LED indicators.
LED Settings
Default = Red LED Off with Laser, Green LED On with Good Scan.
Green LED Off
* Red LED Off
* Green LED On with Good Scan
Red LED On with Good Scan
Green LED On with Laser
Red LED On with Laser
Red LED On when CodeGate 
Disabled
Green LED On when CodeGate 
Disabled
Green LED On when...

3 - 7
LED Brightness
Default = Red High, Green High.
In-Stand and Out-Of-Stand Settings
The following settings program the scanner’s behavior when it is either in the 
stand, or out of the stand (hand-held).  
Red LED On with CTS
Green LED On with CTS
Green Off
Red Off
Green Low
Red Low
Green Medium
Red Medium
* Red High
* Green High 

3 - 8
Caution: When working with In-Stand and Out-of-Stand settings, enable 
the settings you want before disabling those you do not want to 
use.  If you disable settings first, you may program the scanner 
so it is unable to read bar codes.  if this happens, power cycle 
the scanner and scan the defaults bar code on page 1-6.
In-Stand and Out-of-Stand Defaults
If you want the In-Stand or Out-of-Stand default settings restored to your 
scanner, scan the appropriate Defaults bar code below.  They reset...

3 - 9
Presentation Mode with CodeGate® Out-of-Stand:  When the scanner 
is not in the stand, it automatically detects bar codes and decodes them.  
However, the data is not transmitted until you pull the trigger.  The laser 
remains on briefly after the transmission.  (If you are accustomed to a Voy-
ager 9540, this setting is the same as the 9540’s default.)    
Manual Activation Mode
In Manual Activation Mode, you must pull the trigger to scan a bar code.  
The scanner scans until a bar code is read,...

3 - 10
good read.  If you scan Do Not End Manual Activation After Good Read, 
the laser remains on after a good read, but the trigger must be pressed to 
scan the next bar code.  Default = End Manual Activation After Good Read.
Manual Activation Laser Timeout -
Trigger Settings
You can set a timeout for the length of time the laser remains on and 
attempting to decode bar codes when the trigger is held down, and after it 
is released.  Set the length (in milliseconds) for a timeout by scanning one 
of...

3 - 11
CodeGate®
When CodeGate is On, the trigger is used to allow decoded data to be 
transmitted to the host system.  The scanner remains on, scanning and 
decoding bar codes, but the bar code data is not transmitted until the trig-
ger is pressed.  When CodeGate is Off, bar code data is transmitted when 
it is decoded.  Default = CodeGate Off in-Stand, CodeGate On Out-of-
Stand.
Object Detection Mode
Object Detection Mode uses an LED to detect when an object is in the 
scanner’s field of view.  When...

3 - 12
End Object Detection After Good Read
After a bar code is successfully detected and read from the scanner, the 
laser can be programmed either to remain on and scanning, or to turn off.  
When End Object Detection After Good Readis enabled, the laser turns 
off and stops scanning after a good read.  If you scan Do Not End Object 
Detection After Good Read, the laser remains on after a good read.  
Default = End Object Detection After Good Read.
Object Detection Laser Timeout
You can set a timeout...

3 - 13
Object Detection Distance
When the scanner is in the stand and you are using Object Detection 
Mode, you can set the distance range for detecting objects.  Short sets the 
scanner to detect objects approximately 5 inches (12.7cm) away from the 
nose.  Long sets it to detect objects approximately 10 inches (25.4cm) 
away.  Default = Short In-Stand, Long Out-of-Stand.
Character Activation Mode
You may use a character sent from the host to trigger the scanner to begin 
scanning.  When the activation...

3 - 14
to read the alphanumeric combination that represents that ASCII character.  
Scan Save to finish.
End Character Activation After Good Read
After a bar code is successfully detected and read from the scanner, the 
laser can be programmed either to remain on and scanning, or to turn off.  
When End Character Activation After Good Readis enabled, the laser 
turns off and stops scanning after a good read.  If you scan Do Not End 
Character Activation After Good Read, the laser remains on after a good...