Honeywell 1250g2 Manual

2 - 29
data transmission stops.  To resume transmission, the host sends the XON 
character (DC1, hex 11).  Data transmission continues where it left off 
when XOFF was sent.  Default = XON/XOFF Off.
ACK/NAK
After transmitting data, the scanner waits for an ACK character (hex 06) or 
a NAK character (hex 15) response from the host. If ACK is received, the 
communications cycle is completed and the scanner looks for more bar 
codes.  If NAK is received, the last set of bar code data is retransmitted and...

2 - 30
number of retries (from 0-255) by scanning digits from the 
Programming Chart, then scanning Save. (5 is the recommended set-
ting.)  Default = 0.
Communication Timeout Beeper
This selection programs the scanner to issue an error beep when a 
communication timeout has occurred.  The error beep sound is pro-
grammed using Number of Beeps – Error (page 3-4).  Default = On. 
NAK Retries
This selection limits the number of NAK retries that can occur in ACK/NAK 
mode.  Scan the bar code below, then set...

2 - 31
Support BEL/CAN in ACK/NAK
This protocol responds to  and  commands when in ACK/
NAK mode.  The scanner sounds an error tone when a  command is 
sent from the host.   terminates the transmission.  Default = BEL/
CAN Off.
RS232 Defaults
If you want the custom RS232 default settings restored to your scanner, 
scan the RS232 Defaults bar code below.  This resets the scanner to the 
custom default settings (see Setting Custom Defaults on page 1-5).  If 
there are no custom defaults, it will reset the...

2 - 32
Block Check Character
When this selection is set to Tr a n s m i t, the NCR Block Check Character 
(BCC) is expected with incoming messages and transmitted with outgoing 
messages.  Default = Transmit.
NCR Prefix
This selection allows you to program an NCR-specific prefix.  Refer to the 
ASCII Conversion Chart (Code Page 1252)on page A-3 to find the hex 
equivalent for the characters you want for the NCR prefix (typically, 02 for 
STX).  Scan the bar code below, then set the hex number (from 0-FF)...

2 - 33
NCR Prefix/Suffix
When set to Transmit, both the NCR prefix and suffix are transmitted with 
bar codes.  Usually, prefixes and suffixes are programmed using the Data 
Editing selections (see Data Editingbeginning on page 4-1), however, the 
following commands override any other prefix/suffix settings.  Default = 
Don’t Transmit.
NCR NOF (Not-on-File) Error
A scanner receives an NOF (Not on File) command from the POS when-
ever it cannot cross-reference the bar code to a price parameter.  When set...

2 - 34
Scanner-Bioptic Packet Mode
Packet Mode On must be scanned to set the scanner’s format so it is com-
patible with a bioptic scanner.  Default = Packet Mode Off.
ACK/NAK
After transmitting data, the scanner waits for an ACK character (hex 06) or 
a NAK character (hex 15) response from the host. If ACK is received, the 
communications cycle is completed and the scanner looks for more bar 
codes.  If NAK is received, the last set of bar code data is retransmitted and 
the scanner waits for ACK/NAK...

3 - 1
3
Input/Output Settings
Power Up Beeper
The scanner can be programmed to beep when it’s powered up.  Scan the Off 
bar code(s) if you don’t want a power up beep.  Default = Power Up Beeper On 
- Scanner.
Beep on BEL Character
You may wish to force the scanner to beep upon a command sent from the host.  
If you scan the Beep on BEL On bar code below, the scanner will beep every 
time a BEL character is received from the host.  Default = Beep on BEL Off.
Power Up Beeper Off - 
Scanner
* Power Up...

3 - 2
Good Read and Error Indicators
Beeper – Good Read
The beeper may be programmed On or Off in response to a good read.  
Turning this option off, only turns off the beeper response to a good read 
indication.  All error and menu beeps are still audible.  Default = Beeper - 
Good Read On.
Beeper Volume – Good Read
The beeper volume codes modify the volume of the beep the scanner 
emits on a good read.  Default = High.
* Beeper - Good Read On  Beeper - Good Read Off
* HighMedium
Off  Low 

3 - 3
Beeper Pitch – Good Read
The beeper pitch codes modify the pitch (frequency) of the beep the scan-
ner emits on a good read.  Default = Medium.
Beeper - Transmit Order
The beeper transmit order determines when the good read beep occurs.  
The scanner can be set to emit the good read beep either before or after 
data transmission.  Default = Before Transmission.
Beeper Pitch – Error
The beeper pitch codes modify the pitch (frequency) of the sound the scan-
ner emits when there is a bad read or...

3 - 4
Beeper Duration – Good Read
The beeper duration codes modify the length of the beep the scanner emits 
on a good read.  Default = Normal.
Number of Beeps – Good Read
The number of beeps of a good read can be programmed from 1 - 9.  The 
same number of beeps will be applied to the beeper and LED in response 
to a good read.  For example, if you program this option to have five beeps, 
there will be five beeps and five LED flashes in response to a good read.  
The beeps and LED flashes are in sync...