honda nc700 x xa xd owners 2012 User Manual

							18
Operation Guide
Operation Guide
Parts Location
(NC700X/XA)
Rear brake fluid reservoir (P79)
Lower cowl (P67)
Front brake fluid reservoir 
(P79)
Throttle grip (P90)
Engine oil fill cap/dipstick 
(P71)
Engine oil drain bolt (P73)
Engine oil filter (P73)
Coolant reserve tank (P77)
Battery (P70)
Main fuse (P117)
Front brake lever
Rear brake pedal
12 NC700X Revision-42MGS6010.book  18 ページ  ２０１１年１２月１３日　火曜日　午後４時１４分  
						

							19continued
Operation Guide
Shift lever (P37)
Side stand (P82)
Fuel fill cap (P44)
Clutch lever (P87)
Rear Seat (P43)
Drive chain (P83)
Maintenance lid (P66)
Luggage box (P45)
Fuse box (P115)
Crankcase breather (P91)
Windscreen (P93)
12 NC700X Revision-42MGS6010.book  19 ページ  ２０１１年１２月１３日　火曜日　午後４時１４分  
						

							20
Parts Location (Continued)
Operation Guide
(NC700XD)
Rear brake fluid reservoir (P79)
Lower cowl (P67)
Front brake fluid reservoir 
(P79)
Throttle grip (P90)
Engine oil fill cap/dipstick (P71)
Engine oil drain bolt (P73)
Engine oil filter (P73)
Coolant reserve tank (P77)
Battery (P70)
Main fuse (P117)
Front brake lever
Rear brake pedal Clutch oil filter 
(P75)
12 NC700X Revision-42MGS6010.book  20 ページ  ２０１１年１２月１３日　火曜日　午後４時１４分  
						

							21
Operation Guide
Side stand (P82)
Fuel fill cap (P44)
Parking brake lever 
(P81)
Rear Seat (P43)
Drive chain (P83)
Maintenance lid (P66)
Luggage box (P45)
Fuse box (P115)
Crankcase breather (P91)
Windscreen (P93)
12 NC700X Revision-42MGS6010.book  21 ページ  ２０１１年１２月１３日　火曜日　午後４時１４分  
						

							22
Operation Guide
Instruments
Display Check
When the ignition switch is turned on, all the mode and digital segments 
will show, and the tachometer segm ent progress to maximum scale and 
then disappear.
If any part of these displays does not come on when it should, have your 
dealer check for problems. B button
A button
12 NC700X Revision-42MGS6010.book  22 ページ  ２０１１年１２月１３日　火曜日　午後４時１４分  
						

							23continued
Operation Guide
Odometer [TOTAL] & Tripmeter 
[TRIP A/B]
A button switches between 
odometer & tripmeters at the 
ordinary display.
• Odometer: Total distance ridden.
• Tripmeter: Distance ridden since tripmeter was reset (press and 
hold B button to reset to 0.0 km/
mile). Tachometer
NOTICE
Do not operate the engine in the tachometer 
red zone. Excessive engine speed can 
adversely affect engine life.
Clock (12-hour display)
To set the clock: 
(P27)
Fuel gauge
Remaining fuel when only 
1st (E) segment starts flashing:
approximately 2.9 litres 
(0.77 US gal, 0.64 Imp gal)
Speedometer
If the fuel gauge indicator repeat 
flashing or turned off: 
(P101)
Tachometer red zone
(excessive engine rpm range)
(NC700X/XA)
12 NC700X Revision-42MGS6010.book  23 ページ  ２０１１年１２月１３日　火曜日　午後４時１４分  
						

							24
Instruments (Continued)
Operation GuideClock (12-hour display)
To set the clock: 
(P27)
(NC700XD)Odometer [TOTAL] & Tripmeter 
[TRIP A/B]
A button switches between 
odometer & tripmeters at the 
ordinary display.
• Odometer: Total distance ridden.
• Tripmeter: Distance ridden since  tripmeter was reset (press and 
hold B button to reset to 0.0 km/
mile). Tachometer
NOTICE
Do not operate the engine in the tachometer 
red zone. Excessive engine speed can 
adversely affect engine life.
Fuel gauge
Remaining fuel when only 
1st (E) segment starts flashing:
approximately 2.9 litres 
(0.77 US gal, 0.64 Imp gal)
Speedometer
If the fuel gauge indicator repeat 
flashing or  turned off: 
(P101)
Tachometer red zone
(excessive engine rpm range)
12 NC700X Revision-42MGS6010.book  24 ページ  ２０１１年１２月１３日　火曜日　午後４時１４分  
						

							25continued
Operation Guide
D indicator
Comes on when the D mode is selected in the AT MODE. 
(P41)
S indicator
Comes on when the S mode is selected in the AT MODE. 
(P41)
Gear position indicator
The gear position is shown in the gear position  indicator when the D, S mode or MT MODE 
are selected.
u “-” appears for a few seconds and then goes off when the engine starts.
u “-” flashes when the engine stop switch position is changed from Run   to Off   position 
with the ignition switch on.
u “-” flashes when the ignition swit ch is turned on with the engine stop switch Off   position.
The indicator may flash if:
uThe front wheel leaves the ground.
u You turn the wheel while the moto rcycle is upright on the stand.
This is normal. To operate th e system again, turn the ignition switch off, then on again.
If the “-” indicator is blinking in the gear position window while riding: (P100)
12 NC700X Revision-42MGS6010.book  25 ページ  ２０１１年１２月１３日　火曜日　午後４時１４分  
						

							26
Instruments (Continued)
Operation Guide
Display Setting
You can adjust the three settings.
• Backlight brightness adjustment
• Clock setting
• (E, III E type only) Changing of speed and 
mileage unit In addition, to move the ordinary display at 
display setting.
• The button is not pressed for about 30 
seconds
• Turn the ignition switch off and then on
Each setting will be cancelled if the A button 
is not pressed.
1 Backlight brightness adjustment:
You can adjust the brightness three levels.
! a Turn the ignition switch to ON.
! b Press and hold A button and B button until 
the minute digit displays the brightness 
level.
! c Press B button. The brightness is switched.
! d Press A button. The backlight is set, and 
then the display moves to the clock setting.
Ordinary display
Backlight bright ness adjustment
Clock setting
Changing of speed and mileage unit Press and hold A button and B button
Press A button (Except E, III E type)
Press A button (E, III E type only)
Display setting
12 NC700X Revision-42MGS6010.book  26 ページ  ２０１１年１２月１３日　火曜日　午後４時１４分  
						

							27
Operation Guide
2 To set the clock:
!a After backlight brightness adjustment, the 
hour digits start flashing.
! b Press B button until the desired hour and 
AM/PM are displayed.
uPress and hold to advance the hour fast.
! c Press A button. The minute digits start 
flashing.
! d Press B button until the desired minute is 
displayed.
uPress and hold to advance the minute 
fast.
!e
Press A button. The clock is set, and then 
the display returns  to the backlight 
brightness adjustment.
Press A button. The clock is set, and then 
the display moves to  the changing of the 
speed and mileage unit.
3  Changing the speed 
   and mileage unit:
! a After clock setting, the speed and mileage 
unit start flashing.
! b Press B button to select either “km/h” and 
“km” or “mph” and “mile”.
! c Press A button. The speed and mileage unit 
is set, and then the display returns to the 
backlight brightness adjustment.
Except E, III E type
E, III E type only
E, III E type only
12 NC700X Revision-42MGS6010.book  27 ページ  ２０１１年１２月１３日　火曜日　午後４時１４分