Hitachi Projector CP-X8150 User Manual

							51
INPUT menu
ItemDescription
RESOLUTION The resolution for the COMPUTER IN1 and COMPUTER IN2 input 
signals can be set on this projector.
(1)   In the INPUT menu select the RESOLUTION using the ▲/▼ 
buttons and press the ► button. 
The RESOLUTION menu will be   
displayed.
(2)   In the RESOLUTION menu select the 
resolution you wish to display using 
the ▲/▼ buttons.   
Selecting AUTO will set a resolution 
appropriate to the input signal.
(3)   Pressing the ► or ENTER button when 
selecting a STANDARD resolution will 
automatically adjust the horizontal and 
vertical positions, clock phase and 
horizontal size.
The INPUT_INFORMATION dialog will be 
displayed.
(4)    To set a custom resolution use the ▲/▼ buttons to select 
the CUSTOM and the RESOLUTION_CUSTOM box will be 
displayed. 
Set the horizontal (HORZ) and 
vertical (VERT) resolutions using 
the ▲/▼/◄/► buttons.  
This function may not support all 
resolutions.
(5)   Move the cursor to OK on screen and press the ► or ENTER 
button. The message "ARE YOU SURE YOU WISH TO 
CHANGE RESOLUTION?" appears. To save the setting, press 
the ► button.   
The horizontal and vertical positions, clock phase and horizontal 
size will be automatically adjusted.
The INPUT_INFORMATION dialog 
will be displayed.
(6)    To revert back to the previous resolution without saving changes, 
move the cursor to CANCEL on screen and press the ◄ or 
ENTER button. 
The screen will then return to the RESOLUTION menu 
displaying the previous resolution.
• For some pictures, this function may not work well.
STANDARD   ↓
CUSTOM  ↓ 
						

							52
SETUP menu
ItemDescription
AUTO KEYSTONE Selecting this item performs the Automatic keystone distortion 
correction. Projector automatically corrects vertical keystone 
distortion due to the (forward/backward) setup angle by itself.
This function will be executed only once when selected in the menu. 
When the slant of the projector is changed, execute this function again.
• The adjustable range of this function will vary among inputs. For 
some input, this function may not work well.
• When the projector is in one of the following conditions, the 
automatic vertical keystone correction feature may not work 
correctly or at all.
-  
REAR / CEILING or FRONT / CEILING is selected for the 
INSTALLATION item in the SETUP menu, and the projector screen 
is slanted or tilted downwards.
-    The ZOOM adjustment is not set to the full WIDE (wide-angle 
focus).
-    The projector is nearly horizontal (about ±4°).
-   
The projector is inclined at about ±35 degrees or over.
• This function is unavailable when the TRANSITION DETECTOR 
(
 88) is ON or the screen is adjusted by PERFECT FIT (33, 34).
 KEYSTONE Using the ◄/► buttons corrects the vertical keystone distortion.
Shrink the bottom of the image  ó Shrink the top of the image
• The adjustable range of this function will vary among inputs. For 
some input, this function may not work well.
• When the zoom adjustment is set to the TELE (telephoto focus), 
this function may be excessive. This function should be used when 
the zoom adjustment is set to the full WIDE (wide-angle focus) 
whenever possible.
• This function is unavailable when the TRANSITION DETECTOR 
(
 88) is ON or the screen is adjusted by PERFECT FIT (33, 34).
(continued on next page)
SETUP menu
From the SETUP menu, items shown in the table 
below can be performed.
Select an item using the ▲/▼ cursor buttons, and 
press the ► cursor button or ENTER button to 
execute the item. Then perform it according to the 
following table. 
						

							53
SETUP menu
ItemDescription
 KEYSTONEUsing the ◄/► buttons corrects the horizontal keystone distortion.
Shrink the right of the image  ó Shrink the left of the image
• The adjustable range of this function will vary among inputs. For 
some input, this function may not work well.
• When the horizontal lens shift is not set to the center, this function 
may not work well.
• This function is unavailable when the TRANSITION DETECTOR 
(
 88) is ON or the screen is adjusted by PERFECT FIT (33, 34).
PERFECT FIT Selecting this item displays the PERFECT FIT dialog.For details, 
see PERFECT FIT in Correcting the distortion
 (
33, 34).
• This is unavailable when the TRANSITION DETECTOR is ON 
(
 88).
AUTO ECO MODE Using the ▲/▼ buttons turns on/off the AUTO ECO MODE.
ON  ó OFF
• When ON is selected, the projector will always be set to Eco mode 
at start-up regardless of the ECO MODE (
 below) setting. An OSD 
message “AUTO ECO MODE” will be displayed for tens of seconds 
when the projector starts with this function activated.
ECO MODE Using the ▲/▼ buttons turns off/on the Eco mode.
NORMAL  ó ECO
• When the ECO is selected, acoustic noise and screen brightness 
are reduced.
• When AUTO ECO MODE  (
above) is set to ON, the projector will 
always be set to Eco mode at start-up regardless this setting.
INSTALATION Pressing the ►button displays the dialog for changing the 
INSTALLATION setting.
  FRONT / DESKTOP
    
  REAR / DESKTOP
    
  REAR / CEILING
   
  FRONT / CEILING
Use the ▲/▼ buttons to select the desired setting on the 
INSTALLATION dialog, and press the ENTER button of the remote 
control or the INPUT button of the projector to execute.
If TRANSITION DETECTOR is ON and the INSTALLATION status 
is changed, the TRANSITION DETECTOR ON alarm (
 88) will be 
displayed when the projector is restarted.
(continued on next page) 
						

							54
SETUP menu
ItemDescription
STANDBY MODE Using ▲/▼ buttons switches the standby mode setting between 
NORMAL and SAVING. 
NORMAL  ó SAVING
When SAVING is selected, the power consumption in the standby 
mode is lowered with some functional restriction as below:
• When SAVING is selected, the RS-232C communication control 
except to turn the projector on and the network function are disabled 
while the projector is in the standby mode. If the COMMUNICATION 
TYPE in the COMMUNICATION menu is set to NETWORK 
BRIDGE, all of the RS-232C commands are disabled  (
70).
• When SAVING is selected, AUDIO OUT STANDBY setting of 
AUDIO SOURCE (
 55) is invalid, and no signal is output from 
AUDIO OUT port in the standby mode.
• When SAVING is selected, STANDBY setting of MONITOR OUT 
is invalid, and no signal is output from  MONITOR OUT port in the 
standby mode.
• When SAVING is selected, the CENTERING feature while the 
projector is in the standby mode is disabled.
•  When 
SAVING is selected, the Status Monitor and its button operation are 
unavailable while the projector is in the standby mode.
MONITOR OUT While the image signal from the input port chosen in step (1) is 
projected, the image signal from the input port selected in step (2) is 
output to MONITOR OUT port.
(1) Choose a picture input port using ▲/▼ buttons.
Choose STANDBY to select the picture  
output in the standby mode. 
(2)   Select one of the COMPUTER IN ports  
using ◄/► buttons.
Select OFF to disable the MONITOR OUT  
port for the input port or standby mode   
chosen in the step (1).
• You cannot select COMPUTER IN1 in step (1) and COMPUTER IN2 
in step (2) and vice versa. 
						

							55
AUDIO menu
AUDIO menu
From the AUDIO menu, items shown in the table below 
can be performed. Select an item using the ▲/▼ cursor 
buttons, and press the ► cursor button or the ENTER 
button to execute the item. Then perform it according to 
the following table.
 
ItemDescription
VOLUME Using the ◄/► buttons adjusts the volume.
Low  ó High
SPEAKER Using the ▲/▼ buttons turns on/off the built-in speaker.
ON  ó OFF
When OFF is selected, the built-in speaker does not work.
AUDIO SOURCE While the image signal from the input port chosen in step (1) is 
projected, the audio signal from the input port selected in step 
(2) is output to both the AUDIO OUT port and built-in speaker of 
this projector. However, the built-in speaker does not work when 
SPEAKER is set to OFF.
(1)  
Choose a picture input port using the   
▲/▼ buttons.
Choose AUDIO OUT STANDBY to  
select the sound output in the standby   
mode. 
(2)   Select an audio input port or the mute 
icon using the ◄/► buttons.
The icons indicate the following;
No.1: AUDIO IN1 port  No.2: AUDIO IN2 port
No.3: AUDIO IN3 ports  No.4: LAN port
No.5: USB TYPE A ports  No.6: USB TYPE B port
No.7: HDMI 1 port  No.8: HDMI 2 port
 
 : mutes the sound
•  Audio input from port nos.4 to 8 can only be selected by each of 
the picture input ports.
• C.C. (Closed Caption) is automatically activated when 
  is selected 
and an input signal containing C.C. is received. This function is 
available only when the signal is NTSC for VIDEO or S-VIDEO, or 
480i@60 for COMPONENT, COMPUTER IN1 or COMPUTER IN2, 
and when AUTO is selected for DISPLAY in the C.C. menu under the 
SCREEN menu (
 62). 
(continued on next page) 
						

							56
AUDIO menu
ItemDescription
HDMI AUDIO The mode of HDMI
TM audio from the HDMI 1 and 2 ports can be set.
(1)   Use the ▲/▼ buttons to select the 
HDMI port to be set.
(2)   Use the ◄/►buttons to select the 
mode of HDMI
TM audio.
Check each of the two modes provided and select the suitable 
one for your HDMI
TM audio device. 
						

							57
SCREEN menu
SCREEN menu
From the SCREEN menu, items shown in the table 
below can be performed.
Select an item using the ▲/▼ cursor buttons, and 
press the ► cursor button or ENTER button to 
execute the item. Then perform it according to the 
following table.
ItemDescription
LANGUAGE Using the ▲/▼/◄/► buttons switches the OSD (On Screen 
Display) language.
ENGLISH  ó FRANÇAIS 
ó DEUTSCH 
ó  ESPAÑOL
       
   (shown in the LANGUAGE dialog)   
Press the ENTER or INPUT button to save the language setting.
MENU POSITION Using the ▲/▼/◄/► buttons adjusts the menu position.
To quit the operation, press the 
MENU button on the remote control 
or keep no operation for about 10 seconds.
BLANK
Using the ▲/▼ buttons switches the BLANK screen.
The BLANK screen is displayed for the AV MUTE function (
 25). It 
is displayed by pressing the  AV MUTE button on the remote control.
MyScreen  ó ORIGINAL 
ó BLUE 
ó WHITE 
ó BLACK
       
MyScreen :  Screen can be registered by the MyScreen item ( 58).
ORIGINAL
 :  Screen preset as the standard screen.
BLUE, WHITE, BLACK :   Plain screens in each color.
• To avoid remaining as an afterimage, the MyScreen or ORIGINAL 
screen will change to the plain black screen after several minutes.
START UP
Using the ▲/▼ buttons switches the mode for the start-up screen.
The start-up screen is a screen displayed when no signal or an 
unsuitable signal is detected. MyScreen  ó ORIGINAL 
ó OFF
       
MyScreen :  Screen can be registered by the MyScreen item ( 58).
ORIGINAL
 :  Screen preset as the standard screen.
OFF  :  Plain black screen.
• To avoid remaining as an afterimage, the MyScreen or ORIGINAL 
screen will change to the BLANK screen  (
above) after several 
minutes. If also the BLANK screen is the MyScreen or ORIGINAL, 
the plain black screen is instead used.
• When the ON is selected to the MyScreen PASSWORD item in 
the SECURITY menu (
 86), the START UP is fixed to MyScreen.
(continued on next page) 
						

							58
SCREEN menu
ItemDescription
MyScreen This item allows you to capture an image for use as a MyScreen 
image which can be used as the BLANK screen and START UP 
screen. Display the image you want to capture before executing the 
following procedure.
(1)  
Selecting this item displays a dialog 
titled “MyScreen”. It will ask you if 
you start capturing an image from 
the current screen.
Please wait for the target image to be displayed, and press 
the ENTER or INPUT button when the image is displayed. The 
image will freeze and the frame for capturing will appear. 
To stop performing, press the RESET button on the remote 
control. 
(2)   Using the ▲/▼/◄/► buttons adjusts 
the frame position.  
Please move the frame to the position 
of the image which you want to use. 
The frame may not be able to be 
moved for some input signals.  
To start registration, press the ENTER 
or INPUT button on the remote control.
To restore the screen and return to the previous dialog, press the 
RESET button on the remote control. 
Registration may take several minutes.  
When the registration is completed, the registered screen and 
the following message is displayed for several seconds:
“MyScreen registration is finished.”
If the registration failed, the following message is displayed: “A capturing error has occurred. Please try again.” 
• This function cannot be selected when the ON is selected to the 
MyScreen Lock item (
 59).
• This function cannot be selected when the ON is selected to the 
MyScreen PASSWORD item in SECURITY menu (
 86).
• This function is unavailable for a signal from the  LAN, USB TYPE 
A / B or HDMI 1 / 2 port.
•  Drawing with Drawing function cannot be captured  (
102).
(continued on next page) 
						

							59
SCREEN menu
ItemDescription
MyScreen Lock Using the ▲/▼ buttons turns on/off the MyScreen lock function.
ON  ó OFF
When the ON is selected, the item MyScreen is locked. Use this 
function for protecting the current MyScreen.
• This function cannot be selected when the ON is selected to the 
MyScreen PASSWORD item in SECURITY menu (
 86).
MESSAGE Using the ▲/▼ buttons turns on/off the message function.
ON  ó OFF
When the ON is selected, the following message function works. “AUTO IN PROGRESS” while automatically adjusting
“NO INPUT IS DETECTED”
“SYNC IS OUT OF RANGE”
“INVALID SCAN FREQ.”
“NOT AVAILABLE”
“+++ FOCUS +++”
“Searching….” while searching for the input
“Detecting….” while an input signal is detected
“AUTO ECO MODE” while starting up with AUTO ECO MODE 
The indication of the input signal displayed by changing 
The indication of the aspect ratio displayed by changing
The indication of the PICTURE MODE displayed by changing
The indication of the ACTIVE IRIS displayed by changing
The indication of the MY MEMORY displayed by changing
The indication of “FREEZE” and “II” while freezing the screen by 
pressing the  FREEZE button.
The indication of the TEMPLATE displayed by changing.
The indication of the ECO MODE displayed by changing.
• When the OFF is selected, please remember if the picture is 
frozen. Do not mistake freezing for a malfunction  (
36).
(continued on next page) 
						

							60
SCREEN menu
ItemDescription
SOURCE NAME Each input port for this projector can have a name applied to it.
(1)  
Use the ▲/▼ buttons on the SCREEN menu to select SOURCE 
NAME and press the ► or ENTER button.  
The SOURCE NAME menu will be displayed.
(2)   Use the ▲/▼ buttons on the SOURCE 
NAME menu to select the port to be 
named and press the ► button. The 
SOURCE NAME dialog will be displayed.  
Right side of the menu is blank until a 
name is specified.
(3)   Select an icon you would like to assign to 
the port in the SOURCE NAME dialog.   
The name assigned to the port will also 
be automatically switched according to 
your icon selection. Press  the ENTER 
or INPUT button to determine your icon 
selection.
(4)   Select a number you would like to assign 
to the port along with the icon. You can 
select the number either from blank (no 
number assigned), 1, 2, 3, or 4.  
Then press the ENTER or INPUT button.
(5)   If you would like to modify the name assigned 
to the port, select CUSTOM NAME and press 
the ENTER or INPUT button. 
(continued on next page)