Hitachi Projector CP-X8150 User Manual

21
Status Monitor  
  In error state 
The Status Monitor displays a warning of an error 
with larger letters. Resolve the errors referring to the 
table of the sections "Related messages " (
117) and 
"Regarding the indicator lamps " (
118, 119) when the 
warning is displayed.  
Displayed warnings are as below;
COVER: The lamp cover has not been properly fixed.  
Refer to the LAMP indicator blinking in the table  (
118).
FAN: The cooing fan is not operating.  
Refer to the TEMP...

22
When the projector is in a normal condition, 
or dislays one of the warnings of AIR FLOW, 
COLD or FILTER errors, press the FUNCTION 
button on the control panel or press the ENTER 
button on the remote control for three seconds. 
The backlight of the monitor turns on.
   To display the setup information including 
usage time
Use the ◄/►  buttons to switch display. 
     
  
Usage time: The Status Monitor displays  the lamp time (usage time of the present 
lamp), the filter time (usage time of the...

23
AC240V35°C
7FILTERERRO
1PREVIOUS
  To display error history 
Press the ▲ button to display previous error 
log. If a warning has been displayed, the 
first previous error log is the present error 
currently occurring. The Status Monitor 
displays the log number, occurred error, the 
supplied voltage and peripheral temperature 
at that time. Press the  ► button to display 
the usage time when each error occurred. 
Use the ▲/▼ buttons to switch the log. 
The display switches with the ◄/► 
buttons at...

24
1.Make sure that the power cord is firmly 
and correctly connected to the projector 
and the outlet.
Turning on the power
2.Make sure that the POWER indicator is 
lighted in steady orange (
118). Then 
remove the lens cover.
3.Press STANDBY/ON button on the projector  
or the ON button on the remote control.
The projection lamp will light up and  POWER indicator will begin blinking in 
green. When the power is completely on, the indicator will stop blinking and 
light in steady green (
118).
Power...

25
Operating
Operating
1.
Adjusting the volume
Use the VOL + / - buttons to adjust the volume. 
A dialog will appear on the screen to aid you in 
adjusting the volume. If you do not do anything, 
the dialog will automatically disappear after a few 
seconds.• 
When  is selected for current picture input port, the volume 
adjustment is disabled. Please see AUDIO SOURCE item of AUDIO menu (
 55).
• Even if the projector is in the standby mode, the volume is adjustable when 
both of the following conditions...

26
Operating
1.Press INPUT button on the projector. 
Each time you press the button, the projector 
switches its input port from the current port as 
below.
Selecting an input signal
1.Press COMPUTER 1 / 2, LAN, USB TYPE A /  B, HDMI 1 / 2, COMPONENT , 
S-VIDEO or VIDEO button on the remote control. 
The port corresponding to each button is selected as below.
Button Ports
COMPUTER 1 COMPUTER IN1
COMPUTER 2 COMPUTER IN2
LAN LAN
USB TYPE A USB TYPE A
USB TYPE B USB TYPE B
HDMI 1 HDMI 1
HDMI 2 HDMI 2...

27
Operating
Selecting an aspect ratio
  For a computer signal  
CP-X8150 , CP-X8160:   
  NORMAL   
4:3  
  
16:9  
  
16:10 
         
 
CP-WX8240 , CP-WX8255 , CP-SX8350, CP-WU8440 , CP-WU8450:   
  NORMAL   
4:3  
  
16:9  
  
16:10  
  
NATIVE 
        
   For a video signal, s-video signal or component video signal  
CP-X8150 , CP-X8160:   
  4:3  
  
16:9  
  
14:9 
   
 
CP-SX8350:   
  4:3  
  
16:9  
  
14:9  
  
NATIVE 
   
 
CP-WX8240 , CP-WX8255 , CP-WU8440 , CP-WU8450:...

28
Operating
Adjusting the projector’s elevator
When the place to put the projector is slightly uneven 
to the left or right, use the elevator feet to place the 
projector horizontally. 
Using the feet can also tilt the projector in order to 
project at a suitable angle to the screen, elevating the 
front side of the projector within 9 degrees.
This projector has 2 elevator feet and 2 elevator buttons. 
An elevator foot is adjustable while pushing the elevator 
button on the same side as it.
1. 
Holding...

29
Operating
The ZOOM or FOCUS dialog will appear when you 
press any of the buttons from ZOOM, ZOOM -, 
ZOOM + , FOCUS + and FOCUS -. 
1. Use the ZOOM  + / - buttons on the remote 
control or ZOOM  button and ◄/► cursor buttons 
on the projector to adjust the screen size.
2. Use the FOCUS + / -  buttons to focus the picture.
Adjusting the lens 
Adjusting the zoom and focus
• The projector may ignore operation by 
other buttons while the lens is moving.NOTE
Press the LENS SHIFT button. The LENS SHIFT...

30
Operating
• The projector may ignore operation by buttons while moving the lens.
• You can perform the LOAD function using  LENS MEMORY button.NOTE
Adjusting the lens (continued)
This projector is equipped with memory functions for the 
lens adjustments (LENS SHIFT and LENS TYPE). Up 
to 3 sets of adjustments can be stored.
To utilize the lens memory feature, press the 
POSITION 
or FUNCTION button while the LENS SHIFT dialog is 
displayed. Then the LENS MEMORY dialog will ap -
pear. The current lens...