Hitachi Projector CP-WX5500 User Manual

41
Operating
Using the EDGE BLENDING features
1. MODE (MANUAL)
OFF: Disables the Blending function.
MANUAL: Allows you to adjust Blending Region or Blending Level by using menu.
• IMAGE OPTIMIZER is not selectable when Blending is set to other than OFF .
• ECO MODE is not selectable when Blending is set to other than OFF.
2.  BLENDING LEVEL
Select BLENDING LEVEL with ▲/▼ buttons.
[1-25] can be selected with 
◄/► buttons.
Adjust the brightness of Blending Region according to the settings.
3. BLENDING...

42
Operating
(continued on next page) 
4.1 Displaying Cropping Menu
 
Select CROPPING with ▲/▼ buttons and press 
►, 
ENTER or 
 button to display Cropping Menu.  
 
4.2 Setting Cropping  
Select MODE with ▲/▼ buttons and select ON with 
◄/► buttons. 
Input image is automatically cut out according to the 
settings of Blending Region.
4.   CROPPING 
When inputting the same image to each projector, Cropping function enables 
projector to cut out a part of input image and display one image on a large...

43
Operating
 4.3 Adjusting Cropping Area
Adjust Cropping Area when cutting out a part of input image.
Select SETUP with ▲/▼ buttons and press 
►, ENTER or  button.
*  MODE is set to [OFF] temporarily and the guide of Cropping Area  is displayed.
Select [LT]/[WH] with ▲/▼ buttons and press  ENTER or 
 button.
Move the guide display with ▲/▼/
◄/► buttons to select the region of the 
screen to be cut out.
Press ENTER or 
 button and then press ◄ button to select SETUP, and 
MODE switches to ON...

44
Operating
5.  DIMMING LEVEL  
Adjusts the brightness of the projectors which are using Blending.  
Using the ◄/► buttons to adjust the dimming level.
6.   WHITE BALANCE 
Adjusts the white balance of the whole screen.
6.1   OFFSET  
OFFSET adjustments change the color intensity on the whole tones.
6.2   GAIN 
GAIN adjustments mainly affect color intensity on the brighter tones.
• The positional deviation of the screen may occur after installing 
the projector over time. In that case, perform the screen...

45
Operating
1.
Using the magnify feature
2.
3.
4.
Press the MAGNIFY ON button on the remote 
control.  
The picture will be magnified, and the MAGNIFY 
dialog will appear on the screen. When the 
MAGNIFY ON button is pressed for the first time 
after the projector is turned on, the picture will be 
zoomed by 1.5 times. On the dialog, triangle marks 
to show each direction will be displayed.
The display magnification of the projector switches in order 
with every press of the MAGNIFY ON button.
  For...

46
Operating
Press the FREEZE button on the remote control.  
The “FREEZE” indication will appear on the screen 
(however, the indication will not appear when 
SILENT is selected for the OSD MESSAGE item 
in the SETUP (
73)), and the projector will go into the 
FREEZE mode, which the picture is frozen.
To exit the FREEZE mode and restore the screen to  
normal, press the FREEZE button again. 
Temporarily freezing the screen
• The projector automatically exits from the FREEZE mode when some 
control...

47
Operating
The PbyP / PinP is a function for displaying two different picture signals on a 
screen that is separated into main and sub areas for each signal. 
PbyP (Picture by Picture) / PinP (Picture in Picture)
• If the LAN port is selected when the  PbyP button is pressed, input 
from other port is displayed on the main area.
• When in the PbyP / PinP mode, use the MENU button on the remote control 
or ▲/▼ buttons on the control panel to display the OSD menu.
• 
There are  certain functions that...

48
Operating
PbyP (Picture by Picture) / PinP (Picture in Picture) (continued)
The position of the main area can be toggled with the ◄/► buttons when the 
setting information is displayed on the screen. The frame and the audio mark will 
move together with it.   Changing the main area
main 
area sub 
areamain  area
sub 
area
The setting information will be appeared for several seconds when the PbyP  / 
PinP function is started. Displays the input information for each area. A frame 
around the main area...

49
Operating
Press any button to select an input port on the remote control or press the 
INPUT button on the control panel. A dialog box to select the input signal for 
the main area will be displayed. Choose a signal using the ▲/▼ buttons. To 
change the signal in the sub area, switch temporarily across to the main area 
with the ◄/► buttons. 
Displaying the same signal on the both areas is not allowed. Refer to the table 
for details on available input signal combinations. Any combinations marked...

50
Operating
Using ▲/▼ buttons on the remote control changes the size of main area in 
PbyP mode.
  
Changing the size of main area in PbyP mode
1. Select INPUT MENU > PbyP / PinP SETUP > PinP POSITION (
67). 
2. Using ▲/▼ buttons on the remote control changes the position of sub area    
    in PinP mode.
  
Changing the position of sub area in PinP mode
main area
sub area main area
sub area
PbyP (Picture by Picture) / PinP (Picture in Picture) (continued)
• For some signals, it may not be displayed...